======================================================================
-Changes since U-Boot 1.0.0:
+Changes for U-Boot 1.0.2:
======================================================================
+* Patch by Pavel Bartusek, 21 Mar 2004
+ Add Reiserfs support
+
+* Patch by Hinko Kocevar, 20 Mar 2004
+ - Add auto-release for SMSC LAN91c111 driver
+ - Add save/restore of PTR and PNR regs as suggested in datasheet
+
+* Patch by Stephen Williams, 19 March 2004
+ Increase speed of sector reads from SystemACE,
+ shorten poll timeout and remove a useless reset
+
+* Patch by Tolunay Orkun, 19 Mar 2004:
+ Make GigE PHY 1000Mbps Speed/Duplex detection conditional
+ (CONFIG_PHY_GIGE)
+
+* Patch by Brad Kemp, 18 Mar 2004:
+ prevent machine checks during a PCI scan
+
+* Patch by Pierre Aubert, 18 Mar 2004:
+ Fix string cleaning in IDE identification
+
+* Patch by Pierre Aubert, 18 Mar 2004:
+ - Unify video mode handling for Chips & Technologies 69000 Video
+ chip and Silicon Motion SMI 712/710/810 Video chip
+ - Add selection of the video output (CRT or LCD) via 'videoout'
+ environment variable for the Silicon Motion
+ - README update
+
+* Patch by Pierre Aubert, 18 Mar 2004:
+ include/common.h typo fix
+
+* Patches by Tolunay Orkun, 17 Mar 2004:
+ - Add support for bd->bi_iic_fast[] initialization via environment
+ variable "i2cfast" (CONFIG_I2CFAST)
+ - Add "i2cfast" u-boot environment variable support for csb272
+
+* Patch by Carl Riechers, 17 Mar 2004:
+ Ignore '\0' characters in console input for use with telnet and
+ telco pads.
+
+* Patch by Leon Kukovec, 17 Mar 2004:
+ typo fix for strswab prototype #ifdef
+
+* Patches by Thomas Viehweger, 16 Mar 2004:
+ - show PCI clock frequency on MPC8260 systems
+ - add FCC_PSMR_RMII flag for HiP7 processors
+ - in do_jffs2_fsload(), take load address from load_addr if not set
+ explicit, update load_addr otherwise
+ - replaced printf by putc/puts when no formatting is needed
+ (smaller code size, faster execution)
+
+* Patch by Phillippe Robin, 16 Mar 2004:
+ avoid dereferencing NULL pointer in lib_arm/armlinux.c
+
+* Patch by Stephen Williams, 15 Mar 2004:
+ Fix CONFIG_SERIAL_SOFTWARE_FIFO documentation
+
+* Patch by Tolunay Orkun, 15 Mar 2004:
+ Initialize bi_opbfreq to real OPB frequency via get_OPB_freq()
+
+* Patch by Travis Sawyer, 15 Mar 2004:
+ Update CREDITS & MAINTAINERS files for PPC440GX & Ocotea port
+
+* Add start-up delay to make sure power has stabilized before
+ attempting to switch on USB on SX1 board.
+
+* Patch by Josef Wagner, 18 Mar 2004:
+ - Add support for MicroSys XM250 board (PXA255)
+ - Add support for MicroSys PM828 board (MPC8280)
+ - Add support for 32 MB Flash on PM825/826
+ - new SDRAM refresh rate for PM825/PM826
+ - added support for MicroSys PM520 (MPC5200)
+ - replaced Query by Identify command in CPU86/flash.c
+ to support 28F160F3B
+
+* Fix wrap around problem with udelay() on ARM920T
+
+* Add support for Macronix flash on TRAB board
+
+* Patch by Pierre Aubert, 15 Mar 2004:
+ Fix buffer overflow in IDE identification
+
+* Fix power-off of LCD for out-of-band temperatures on LWMON board
+
+* Remove redundand #define in IceCube.h
+
+* Patch by Steven Scholz, 27 Feb 2004:
+ - Adding get_ticks() and get_tbclk() for AT91RM9200
+ - Many white space fixes in cpu/at91rm9200/interrupts.c
+
+* Patches by Steven Scholz, 20 Feb 2004:
+ some cleanup in AT91RM9200 related code
+
+* Patches by Travis Sawyer, 12 Mar 2004:
+ - Fix Gigabit Ethernet support for 440GX
+ - Add Gigabit Ethernet Support to MII PHY utilities
+
+* Patch by Brad Kemp, 12 Mar 2004:
+ Fixes for drivers/cfi_flash.c:
+ - Better support for x8/x16 implementations
+ - Added failure for AMD chips attempting to use CFG_FLASH_USE_BUFFER_WRITE
+ - Added defines for AMD command and address constants
+
+* Patch by Leon Kukovec, 12 Mar 2004:
+ Fix get_dentfromdir() to correctly handle deleted dentries
+
+* Patch by George G. Davis, 11 Mar 2004:
+ Remove hard coded network settings in TI OMAP1610 H2
+ default board config
+
+* Patch by George G. Davis, 11 Mar 2004:
+ add support for ADS GraphicsClient+ board.
+
+* Patch by Pierre Aubert, 11 Mar 2004:
+ - add bitmap command and splash screen support in cfb console
+ - add [optional] origin in the bitmap display command
+
+* Patch by Travis Sawyer, 11 Mar 2004:
+ Fix ocotea board early init interrupt setup.
+
+* Patch by Thomas Viehweger, 11 Mar 2004:
+ Remove redundand code; add PCI-specific bits to include/mpc8260.h
+
+* Patch by Stephan Linz, 09 Mar 2004
+ - Add support for the SSV ADNP/ESC1 (Nios Softcore)
+
+* Patch by George G. Davis, 9 Mar 2004:
+ fix recent build failure for SA1100 target
+
+* Patch by Travis Sawyer, 09 Mar 2004:
+ Support native interrupt mode for the IBM440GX.
+ Previously it was running in 440GP compatibility mode.
+
+* Patch by Philippe Robin, 09 Mar 2004:
+ Added ARM Integrator AP, CP and Versatile PB926EJ-S Reference
+ Platform support.
+
+* Patch by Masami Komiya, 08 Mar 2004:
+ Don't overwrite server IP address or boot file name
+ when the boot server does not return values
+
+* Patch by Tolunay Orkun, 5 Mar 2004:
+ Removed compile time restriction on CFG_I2C_SPEED for DS1338 RTC
+
+* Patch by Tolunay Orkun, 5 Mar 2004:
+ Fix early board initialization for Cogent CSB272 board
+
+* Patch by Ed Okerson, 3 Mar 2004:
+ fix CFI flash writes for little endian systems
+
+* Patch by Reinhard Meyer, 01 Mar 2004:
+ generalize USB and IDE support for MPC5200 with according
+ changes to IceCube.h and TOP5200.h
+ add Am29LV256 256 MBit FLASH support for TOP5200 boards
+ add info about USB and IDE to README
+
+* Patch by Yuli Barcohen, 4 Mar 2004:
+ Fix problems with GCC 3.3.x which changed handling of global
+ variables explicitly initialized to zero (now in .bss instead of
+ .data as before).
+
+* Patch by Leon Kukovec, 02 Mar 2004:
+ add strswab() to fix IDE LBA capacity, firmware and model numbers
+ on little endian machines
+
+* Patch by Masami Komiya, 02 Mar 2004:
+ - Remove get_ticks() from NFS code
+ - Add verification of RPC transaction ID
+
+* Patch by Pierre Aubert, 02 Mar 2004:
+ cleanup for IDE and USB drivers for MPC5200
+
+* Patch by Travis Sawyer, 01 Mar 2004:
+ Ocotea:
+ - Add IBM PPC440GX Ref Platform support (Ocotea)
+ Adapted to U-Boot and 440GX port
+ 440gx_enet.c:
+ - Add gracious handling of all Ethernet Pin Selections for 440GX
+ - Add RGMII selection for Cicada CIS8201 Gigabit PHY
+ ppc440.h:
+ - Add needed bit definitions
+ - Fix formatting
+
+* Patch by Carl Riechers, 1 Mar 2004:
+ Add PPC440GX prbdv0 divider to fix memory clock calculation.
+
+* Patch by Stephan Linz, 27 Feb 2004
+ - avoid problems for targets without NFS download support
+
+* Patch by Rune Torgersen, 27 Feb 2004:
+ - Added LBA48 support (CONFIG_LBA48 & CFG_64BIT_LBA)
+ - Added support for 64bit printing in vsprintf (CFG_64BIT_VSPRINTF)
+ - Added support for 64bit strtoul (CFG_64BIT_STRTOUL)
+
+* Patch by Masami Komiya, 27 Feb 2004:
+ Fix rarpboot: add autoload by NFS
+
+* Patch by Dan Eisenhut, 26 Feb 2004:
+ fix flash_write return value in saveenv
+
+* Patch by Stephan Linz, 11 Dec 2003
+ expand config.mk to avoid trigraph warnings on NIOS
+
+* Rename "BMS2003" board into "HMI10"
+
+* SX1 patches: use "serial#" for USB serial #; use redundand environment
+ storage; auto-set console on USB port (using preboot command)
+
+* Add support for SX1 mobile phone; add support for USB-based console
+ (enable with "setenv stdout usbtty; setenv stdin usbtty")
+
+* Fix LOWBOOT configuration for MPC5200 with DDR memory
+
+* Fix SDRAM timings for LITE5200 / IceCube board
+
+* Handle Auti-MDIX / connection status for INCA-IP
+
+* Fix USB problems when attempting to read 0 bytes
+
+* Patch by Travis Sawyer, 26 Feb 2004:
+ Fix broken compile for XPEDITE1K target.
+
+* Patch by Stephan Linz, 26 Feb 2004:
+ Bug fix for NFS code on NIOS targets
+
+* Patch by Stephen Williams, 26 Feb 2004:
+ Break up SystemACE reads of large block counts
+
+* Patch by Pierre Aubert, 26 Feb 2004
+ add IDE support for MPC5200
+
+* Patch by Masami Komiya, 26 Feb 2004:
+ add autoload via NFS
+
+* Patch by Stephen Williams
+ Use of CONFIG_SERIAL_SOFTWARE_FIFO in board.c consistent with uses
+ elsewhere in the source.
+
+* Patch by Steven Scholz, 25 Feb 2004:
+ - Timeouts in FPGA code should be based on CFG_HZ
+ - Minor cleanup in code for Altera FPGA ACEX1K
+
+* Patch by Steven Scholz, 25 Feb 2004:
+ Changed "Directory Hierarchy" section in README
+
+* Patch by Masami Komiya, 25 Feb 2004:
+ Reduce copy count in nfs_read_reply() of NFS code
+
+* Patch by Markus Pietrek, 24 Feb 2004:
+ NS9750 DevBoard added
+
+* Patch by Pierre Aubert, 24 Feb 2004
+ add USB support for MPC5200
+
+* Patch by Steven Scholz, 24 Feb 2004:
+ - fix MII commands to use values from last command
+
+* Patch by Torsten Demke, 24 Feb 2004:
+ Add support for the eXalion platform (SPSW-8240, F-30, F-300)
+
+* Patch by Rahul Shanbhag, 19 Feb 2004:
+ Fixes for for OMAP1610 board:
+ - shift some IRQ specific code to platform.S file
+ - remove duplicatewatchdog reset code from start.S
+
+* Make Auto-MDIX Support configurable on INCA-IP board
+
+* Fix license for mkimage tool
+
+* Patch by Masami Komiya, 24 Feb 2004:
+ Update NetBootFileXferSize in NFS code
+
+* Patch by Scott McNutt, 24 Feb 2004:
+ fix packet length in NFS code
+
+* Patch by Masami Komiy, 22 Feb 2004:
+ Add support for NFS for file download
+
+* Patch by Andrea Scian, 17 Feb 2004:
+ Add support for S3C44B0 processor and DAVE B2 board
+
+* Patch by Steven Scholz, 20 Feb 2004:
+ - Add support for MII commands on AT91RM9200 boards
+ - some cleanup in AT91RM9200 ethernet code
+
+* Patch by Peter Ryser, 20 Feb 2004:
+ Add support for the Xilinx ML300 platform
+
+* Patch by Stephan Linz, 17 Feb 2004:
+ Fix watchdog support for NIOS
+
+* Patch by Josh Fryman, 16 Feb 2004:
+ Fix byte-swapping for cfi_flash.c for different bus widths
+
+* Patch by Jon Diekema, 14 Jeb 2004:
+ Remove duplicate "FPGA Support" notes from the README file
+
+* Patches by Reinhard Meyer, 14 Feb 2004:
+ - update board/emk tree; use common flash driver
+ - Corrected tested bits in machine check exception in cpu/mpc5xxx/traps.c
+ [adapted for other PPC CPUs -- wd]
+ - Added support for the M48T08 on the EVAL5200 board in rtc/mk48t59.c
+
+* Patch by Jon Diekema, 13 Feb 2004:
+ Call show_boot_progress() whenever POST "FAILED" is printed.
+
+* Patch by Nishant Kamat, 13 Feb 2004:
+ Add support for TI OMAP1610 H2 Board
+ Fixes for cpu/arm926ejs/interrupt.c
+ (based on Richard Woodruff's patch for arm925, 16 Oct 03)
+ Fix for a timer bug in OMAP1610 Innovator
+ Add support for CS0 (ROM)/CS3 (Flash) boot in OMAP1610 Innovator and H2
+
+* Patches by Stephan Linz, 12 Feb 2004:
+ - add support for NIOS timer with variable period preload counter value
+ - prepare POST framework support for NIOS targets
+
+* Patch by Denis Peter, 11 Feb 2004:
+ add POST support for the MIP405 board
+
+* Patch by Laurent Mohin, 10 Feb 2004:
+ Fix buffer overflow in common/usb.c
+
+* Patch by Tolunay Orkun, 10 Feb 2004:
+ Add support for Cogent CSB272 board
+
+* Patch by Thomas Elste, 10 Feb 2004:
+ Add support for NET+50 CPU and ModNET50 board
+
+* Patch by Sam Song, 10 Feb 2004:
+ Fix typos in cfi_flash.c
+
+* Patch by Leon Kukovec, 10 Feb 2004
+ Fixed long dir entry slot id calculation in get_vfatname
+
+* Patch by Robin Gilks, 10 Feb 2004:
+ add "itest" command (operators: -eq, -ne, -lt, -gt, -le, -ge, ==,
+ !=, <>, <, >, <=, >=)
+
+* Fix problem with side effects in macros in include/usb.h
+
+* Patch by David Benson, 13 Nov 2003:
+ bug 841358 - fix TFTP download size limit
+
+* Fixing bug 850768:
+ improper flush_cache() in load_serial()
+
+* Fixing bug 834943:
+ MPC8540 - missing volatile declarations
+
+* Patch by Stephen Williams, 09 Feb 2004:
+ Add support for Xilinx SystemACE chip:
+ - New files common/cmd_ace.c and include/systemace.h
+ - Hook systemace support into cmd_fat and the partition manager
+
+* Patch by Travis Sawyer, 09 Feb 2004:
+ Add bi_opbfreq & bi_iic_fast to 440GX bd_info as needed for Linux
+
+* Patch by Travis Sawyer, 09 Feb 2004:
+ o 440GX:
+ - Fix PCI Indirect access for type 1 config cycles with ppc440.
+ - Add phymode for 440 enet
+ - fix pci pre init
+ o XPedite1K:
+ - Change board_pre_init to board_early_init_f
+ - Add user flash to bus controller setup
+ - Fix pci pre init
+ - Fix is_pci_host to check GPIO for monarch bit
+ - Force xpedite1k to pci conventional mode (via #define option)
+
+* Patch by Brad Kemp, 4 Feb 2004:
+ - handle the machine check that is generated during the PCI scans
+ on 82xx processors.
+ - define the registers used in the IMMR by the PCI subsystem.
+
+* Patch by Pierre Aubert, 03 Feb 2004:
+ cpu/mpc5xxx/start.S: copy MBAR into SPR311
+
+* Patch by Jeff Angielski, 03 Feb 2004:
+ Fix copy & paste error in cpu/mpc8260/pci.c
+
+* Patch by Reinhard Meyer, 24 Jan 2004:
+ Fix typo in cpu/mpc5xxx/pci_mpc5200.c
+
+* Add Auto-MDIX support for INCA-IP
+
+* Some code cleanup
+
+* Patch by Josef Baumgartner, 10 Feb 2004:
+ Fixes for Coldfire port
+
+* Patch by Brad Kemp, 11 Feb 2004:
+ Fix CFI flash driver problems
+
+* Make sure to use a bus clock divider of 2 only when running TQM8xxM
+ modules at CPU clock frequencies above 66 MHz.
+
+* Optimize flash programming speed for LWMON (by another 100% :-)
+
+* Patch by Jian Zhang, 3 Feb 2004:
+ - Changed the incorrect FAT12BUFSIZE
+ - data_begin in fsdata can be negative. Changed it to be short.
+
+* Patches by Stephan Linz, 30 Jan 2004:
+ 1: - board/altera/common/flash.c:flash_erase():
+ o allow interrupts befor get_timer() call
+ o check-up each erased sector and avoid unexpected timeouts
+ - board/altera/dk1c20/dk1s10.c:board_early_init_f():
+ o enclose sevenseg_set() in cpp condition
+ - remove the ASMI configuration for DK1S10_standard_32 (never present)
+ - fix some typed in mistakes in the NIOS documentation
+ 2: - split DK1C20 configuration into several header files:
+ o two new files for each NIOS CPU description
+ o U-Boot related part is remaining in DK1C20.h
+ 3: - split DK1S10 configuration into several header files:
+ o two new files for each NIOS CPU description
+ o U-Boot related part is remaining in DK1S10.h
+ 4: - Add support for the Microtronix Linux Development Kit
+ NIOS CPU configuration at the Altera Nios Development Kit,
+ Stratix Edition (DK-1S10)
+ 5: - Add documentation for the Altera Nios Development Kit,
+ Stratix Edition (DK-1S10)
+ 6: - Add support for the Nios Serial Peripharel Interface (SPI)
+ (master only)
+ 7: - Add support for the common U-Boot SPI framework at
+ RTC driver DS1306
+
+* Patch by Rahul Shanbhag, 28 Jan 2004:
+ Fix flash protection/locking handling for OMAP1610 innovator board.
+
+* Patch by Rolf Peukert, 28 Jan 2004:
+ fix flash write problems on CSB226 board (write with 32 bit bus width)
+
+* Patches by Mark Jonas, 16 Jan 2004:
+ - fix rounding error when calculating baudrates for MPC5200 PSCs
+ - make sure CFG_RAMBOOT and CFG_LOWBOOT are not enabled at the same
+ time which is not supported
+
+* Patch by Yuli Barcohen, 26 Jan 2004:
+ Allow bzip2 compression for small memory footprint boards
+
+* Patch by Brad Kemp, 21 Jan 2004:
+ Add support for CFI flash driver for both the Intel and the AMD
+ command sets.
+
+* Patch by Travis Sawyer, 20 Jan 2004:
+ Fix pci bridge auto enumeration of sibling p2p bridges.
+
+* Patch by Tolunay Orkun, 12 Jan 2004:
+ Add some delays as needed for Intel LXT971A PHY support
+
+* Patches by Stephan Linz, 09 Jan 2004:
+ - avoid warning: unused variable `piop' in board/altera/common/sevenseg.c
+ - make DK1C20 board configuration related to ASMI conform to
+ documentation
+
+* Patch by Anders Larsen, 09 Jan 2004:
+
+ ARM memory layout fixes: the abort-stack is now set up in the
+ correct RAM area, and the BSS is zeroed out as it should be.
+
+ Furthermore, the magic variables 'armboot_end' and 'armboot_end_data'
+ of the linker scripts are replaced by '__bss_start' and '_end',
+ resp., which is a further step to eliminate unnecessary differences
+ between the implementation of the CPU architectures.
+
+* Patch by liang a lei, 9 Jan 2004:
+ Fix Intel 28F128J3 ID in include/flash.h
+
+* Patch by Masami Komiya, 09 Jan 2004:
+ add support for TB0229 board (NEC VR4131 MIPS processor)
+
+* Patch by Leon Kukovec, 12 Dec 2003:
+ changed extern __inline__ into static __inline__ in
+ include/linux/byteorder/swab.h
+
+* Patch by Travis Sawyer, 30 Dec 2003:
+ Add support for IBM PPC440GX. Multiple EMAC Ethernet devices,
+ select MDI port based on enabled EMAC device.
+ Add support for XES Inc <http://www.xes-inc.com> XPedite1000 440GX
+ base PrPMC board.
+
+* Patch by Wolter Kamphuis, 15 Dec 2003:
+ made CONFIG_SILENT_CONSOLE usable on all architectures
+
+* Disable date command on TQM866M - there is no RTC on MPC866
+
+* Fix variable CPU clock for MPC859/866 systems for low CPU clocks
+
+* Implement adaptive SDRAM timing configuration based on actual CPU
+ clock frequency for INCA-IP; fix problem with board hanging when
+ switching from 150MHz to 100MHz
+
+* Add PCMCIA CS support for BMS2003 board
+
+* Add variable CPU clock for MPC859/866 systems (so far only TQM866M):
+ see doc/README.MPC866 for details;
+ implement workaround for "SIU4" and "SIU9" silicon bugs on MPC866;
+ calculate CPU clock frequency from PLL register values.
+
+* Add support for 128 MB RAM on TQM8xxL/M modules
+
+* Fix PS/2 keyboard problem caused by statically initialized variable
+ pointing to a location in flash
+
+* Fix INCA-IP clock calculation: 400/3 = 133.3 MHz, not 130.
+
+* The PS/2 mux on the BMS2003 board needs 450 ms after power on
+ before we can access it; add delay in case we are faster (with no
+ CF card inserted)
+
+* Cleanup of some init functions
+
+* Make sure SCC Ethernet is always stopped by the time we boot Linux
+ to avoid Linux crashes by early packets coming in.
+
+* Accelerate flash accesses on LWMON board by using buffered writes
+
+* Fix typo in Makefile;
+ fix problem with PARTNUM detection
+
+* Patch by Reinhard Meyer, 09 Jan 2004:
+ - add RTC support for MPC5200 based boards (requires RTC_XTAL)
+
+* Add support for IDE LED on BMS2003 board
+ (exclusive with status LED!)
+
+* Add support for PS/2 keyboard (used with PS/2 multiplexor on
+ BMS2003 board)
+
+* Patches by Reinhard Meyer, 4 Jan 2004 + 7 Jan 2004:
+ Add common files for "emk" boards
+
+* Add a common get_ram_size() function and modify the the
+ board-specific files to invoke that common implementation.
+
+======================================================================
+Changes for U-Boot 1.0.1:
+======================================================================
+
+* Set default clock for INCA-IP to 150 MHz
+
+* Make BMS2003 use a separate config file to avoid #ifdef mess;
+ add I2C support; add support for DS1337 RTC
+
+* Add CompactFlash support for BMS2003 board
+
+* Add support for status LED on BMS2003 board
+
+* Patch by Scott McNutt, 02 Jan 2004:
+ Add support for the Nios Active Serial Memory Interface (ASMI)
+ on Cyclone devices
+
+* Patch by Andrea Marson, 16 Dec 2003:
+ Add support for the PPChameleon ME and HI modules
+
+* Patch by Yuli Barcohen, 22 Dec 2003:
+ Add support for Motorola DUET ADS board (MPC87x/88x)
+
+* Patch by Robert Schwebel, 15 Dec 2003:
+ add support for cramfs (uses JFFS2 command interface)
+
+* Patches by Stephan Linz, 11 Dec 2003:
+ - more documentation for NIOS port
+ - new struct nios_pio_t, struct nios_spi_t
+ - Reconfiguration for NIOS Development Kit DK1C20:
+ o move board related code from board/dk1c20
+ to board/altera/dk1c20
+ o create a new common source path board/altera/common
+ and move generic flash access stuff into it
+ o change/expand configuration file DK1C20.h
+ - Add support for NIOS Development Kit DK1S10
+ - Add status LED support for NIOS systems
+ - Add dual 7-segment LED support for Altera NIOS DevKits
+
+* Patch by Ronen Shitrit, 10 Dec 2003:
+ Add support for the Marvell DB64360 / DB64460 development boards
+
+* Patch by Detlev Zundel, 10 Dec 2003:
+ fix dependency problem in examples/Makefile
+
+* Patch by Denis Peter, 8 Dec 2003
+ - add support for the PATI board (MPC555)
+ - add SPI support for the MPC5xx
+
+* Patch by Anders Larsen, 08 Dec 2003:
+ add configuration options CONFIG_SERIAL_TAG and CONFIG_REVISION_TAG
+ to pass ATAG_SERIAL and ATAG_REVISION, resp., to the ARM target;
+ cleanup some redundand #defines
+
+* Patch by André Schwarz, 8 Dec 2003:
+ fixes for Davicom DM9102A Ethernet Chip (#define CONFIG_TULIP_FIX_DAVICOM):
+ - TX and RX deskriptors must be quad-word aligned
+ - does not work with only one TX deskriptor
+ - standard reset method does not work
+
+* Patch by Masami Komiya, 08 Dec 2003:
+ add RTL8139 ethernet driver
+
+* Patches by Ed Okerson, 07 Dec 2003:
+ - fix ethernet for the AU1x00 processors in little-endian mode.
+ - extend memsetup.S for the AU1x00 processors in BE and LE modes
+
+* Minor code cleanup (coding style)
+
+* Patch by Reinhard Meyer, 30 Dec 2003:
+ - cpu/mpc5xxx/fec.c: added CONFIG_PHY_ADDR, added CONFIG_PHY_TYPE,
+ - added CONFIG_PHY_ADDR to include/configs/IceCube.h,
+ - turned debug print of PHY registers into a function (called in two places)
+ - added support for EMK MPC5200 based modules
+
+* Fix MPC8xx PLPRCR_MFD_SHIFT typo
+
+* Add support for TQM866M modules
+
+* Fixes for TQM855M with 4 MB flash (Am29DL163 = _no_ mirror bit flash)
+
+* Fix a few compiler warnings
+
+* Patch by Reinhard Meyer, 28 Dec 2003:
+ Add initial support for TOP5200 board
+
+* Make CPU clock on ICA-IP board controllable by a "cpuclk"
+ environment variable which can set to "100", "133", or "150". The
+ CPU clock will be configured accordingly upon next reboot. Other
+ values are ignored. In case of an invalid or undefined "cpuclk"
+ value, the compile-time default CPU clock speed will be used.
+
+* Enable Quad-UART on BMS2003 board (initialize the PCMCIA memory
+ window that is used to access the UART registers by the Linux driver)
+
+* Patch by Reinhard Meyer, 20 Dec 2003:
+ Fix clock calculation for the MPC5200 for higher clock frequencies
+ (above 2**32 / 10 = 429.5 MHz).
+
+* Fix CONFIG_PLL_PCI_TO_MEM_MULTIPLIER divider error in SP8240 configuration
+
+* Fix IceCube CLKIN configuration (it's 33.000000MHz)
+
+* Add new configuration for IceCube board with DDR memory
+
+* Update TRAB memory configurations
+
+* Add JFFS2 support for INCA-IP board
+
+* Patch by Bill Hargen, 09 Dec 2003:
+ - BUBINGA405EP: changed flash driver to protect top sector containing
+ first instruction.
+ - BUBINGA405EP: configured "eeprom" command to access boot config EEPROM.
+ - BUBINGA405EP: fixed PLL init (init chip selects before FPGA/NVRAM access).
+ - 405EP: fixed SPD-based SDRAM init (only use banks 0 and 1).
+ - 405EP: added/fixed support for "reginfo" command.
+ - 4xx: removed spurious MII error messages on "mii info" command.
+
+* Patch by Bernhard Kuhn, 28 Nov 2003:
+ add support for Coldfire CPU
+ add support for Motorola M5272C3 and M5282EVB boards
+
+* Patch by Pierre Aubert, 24 Nov 2003:
+ - add a return value for the fpga command
+ - add ide_preinit() function called in ide_init if CONFIG_IDE_PREINIT
+ is defined. If ide_preinit fails, ide_init is aborted.
+ - fix an endianess problem in fat.h
+
+* Patch by Wolter Kamphuis, 05 Dec 2003:
+ Add support for SNMC's QS850/QS823/QS860T boards
+
+* Patch by Yuli Barcohen, 3 Dec 2003:
+ "revive" U-Boot support for old Motorola MPC860ADS board
+
+* Patch by Cam(ilo?), 03 Dec 2003:
+ make examples build even with broken Montavista objcopy
+
+* Patch by Pavel Bartusek, 27 Nov 2003:
+ fix conversion problem with "bootretry" evironment variable
+
+* Patch by Andre Schwarz, 24 Nov 2003:
+ add support for mvblue (mvBlueLYNX and mvBlueBOX) boards
+
+* Patch by Pavel Bartusek, 21 Nov 2003:
+ set ZMII bridge speed on 440
+
+* Patch by Anders Larsen, 17 Nov 2003:
+ Fix mismatched #ifdef / #endif in include/asm-arm/arch-pxa/hardware.h
+
+* Patches by David Müller, 14 Nov 2003:
+ - board/mpl/common/common_util.c
+ * implement support for BZIP2 compressed images
+ * various cleanups (printf -> puts, ...)
+ - board/mpl/common/flash.c
+ * report correct errors to upper layers
+ * check the erase fail and VPP low bits in status reg
+ - board/mpl/vcma9/cmd_vcma9.c
+ - board/mpl/vcma9/flash.c
+ * various cleanups (printf -> puts, ...)
+ - common/cmd_usb.c
+ * fix typo in comment
+ - cpu/arm920t/usb_ohci.c
+ * support for S3C2410 is missing in #if line
+ - drivers/cs8900.c
+ * reinit some registers in case of error (cable missing, ...)
+ - fs/fat/fat.c
+ * support for USB/MMC devices is missing in #if line
+ - include/configs/MIP405.h
+ - include/configs/PIP405.h
+ * enable BZIP2 support
+ * enlarge malloc space to 1MiB because of BZIP2 support
+ - include/configs/VCMA9.h
+ * enable BZIP2 support
+ * enlarge malloc space to 1MiB because of BZIP2 support
+ * enable USB support
+ - lib_arm/armlinux.c
+ * change calling convention of ARM Linux kernel as
+ described on http://www.arm.linux.org.uk/developer/booting.php
+
+* Patch by Thomas Lange, 14 Nov 2003:
+ Split dbau1x00 into dbau1000, dbau1100 and dbau1500 configs to
+ support all these AMD boards.
+
+* Patch by Thomas Lange, 14 Nov 2003:
+ Workaround for mips au1x00 physical memory accesses (the au1x00
+ uses a 36 bit bus internally and cannot access physical memory
+ directly. Use the uncached SDRAM address instead of the physical
+ one.)
+
+* Patch by Xue Ligong (Joe), 13 Nov 2003:
+ add Realtek 8019 ethernet driver
+
+* Patch by Yuli Barcohen, 13 Nov 2003:
+ MPC826xADS/PQ2FADS cleanup
+
+* Patch by Anders Larsen, 12 Nov 2003:
+ Update README to mark the PORTIO commands non-standard
+
+* Patch by Nicolas Lacressonnière, 12 Nov 2003:
+ update for for Atmel AT91RM9200DK development kit:
+ - support for environment variables in DataFlash
+ - Atmel DataFlash AT45DB1282 support
+
+* Patch by Jeff Carr, 11 Nov 2003:
+ add support for new version of 8270 processors
+
+* Patches by George G. Davis, 05 Nov 2003:
+ - only pass the ARM linux initrd tag to the kernel when an initrd
+ is actually present
+ - update omap1510inn configuration file
+
+* Patches by Stephan Linz, 3 Nov 2003:
+ - more endianess fixes for LAN91C111 driver
+ - CFG_HZ configuration patch for NIOS Cyclone board
+
+* Patch by Stephan Linz, 28 Oct 2003:
+ fix PHY_INT_REG vs. PHY_MASK_REG bug in drivers/smc91111.c
+
+* Patch by Steven Scholz, 20 Oct 2003:
+ - make "mii info <addr>" show infor for PHY at "addr" only
+ - Endian fix for miiphy_info()
+
+* Patch by Gleb Natapov, 19 Sep 2003:
+ Move most of the timer interrupt related PPC code to ppc_lib/interrupts.c
+
+* Patch by Anders Larsen, 17 Sep 2003:
+ Bring ARM memory layout in sync with the documentation:
+ stack and malloc-heap are now located _below_ the U-Boot code
+
+* Accelerate booting on TRAB board: read and check autoupdate image
+ headers first instead of always reading the whole images.
+
* Fix type in MPC5XXX code (pointed out by Victor Wren)
* Enabled password check on RMU board
projects / J-u-boot.git / blobdiff