serial: Use the default CONFIG_SYS_BAUDRATE_TABLE in more platforms

[J-u-boot.git] / configs / ls1046aqds_nand_defconfig

diff --git a/configs/ls1046aqds_nand_defconfig b/configs/ls1046aqds_nand_defconfig
index c406d866bd0c905413d8cf43c16256411b43ffc1..597938139db4e9f2b7a8cf9d84315f426261f0af 100644 (file)
--- a/configs/ls1046aqds_nand_defconfig
+++ b/configs/ls1046aqds_nand_defconfig
@@ -6,18 +6,25 @@ CONFIG_SYS_MEMTEST_START=0x80000000
 CONFIG_SYS_MEMTEST_END=0x9fffffff
 CONFIG_ENV_SIZE=0x2000
 CONFIG_ENV_OFFSET=0x300000
+CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_SYS_I2C_MXC_I2C2=y
+CONFIG_SYS_I2C_MXC_I2C3=y
+CONFIG_SYS_I2C_MXC_I2C4=y
+CONFIG_SYS_MALLOC_LEN=0x102000
 CONFIG_DM_GPIO=y
 CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart"
 CONFIG_SPL_TEXT_BASE=0x10000000
 CONFIG_FSL_USE_PCA9547_MUX=y
 CONFIG_FSL_LS_PPA=y
-CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_SERIAL=y
 CONFIG_SPL=y
 CONFIG_AHCI=y
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL"
+CONFIG_RAMBOOT_PBL=y
+CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1046aqds/ls1046aqds_pbi.cfg"
+CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg"
 CONFIG_NAND_BOOT=y
 CONFIG_BOOTDELAY=10
 CONFIG_USE_BOOTARGS=y
@@ -28,9 +35,11 @@ CONFIG_SPL_FSL_PBL=y
 CONFIG_SPL_BOARD_INIT=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x110
+CONFIG_SPL_MPC8XXX_INIT_DDR=y
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_IMLS=y
 CONFIG_CMD_GREPENV=y
+CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
 CONFIG_CMD_MEMINFO=y
 CONFIG_CMD_MEMTEST=y
 CONFIG_CMD_GPIO=y
@@ -50,7 +59,12 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_DM=y
 CONFIG_SATA_CEVA=y
 CONFIG_FSL_CAAM=y
+CONFIG_DYNAMIC_DDR_CLK_FREQ=y
+CONFIG_DDR_ECC=y
+CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
 CONFIG_DM_I2C=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_SYS_I2C_EEPROM_ADDR=0x57
 CONFIG_FSL_ESDHC=y
 CONFIG_MTD=y
 CONFIG_MTD_NOR_FLASH=y