bool "MMC/SD/SDIO card support"
default ARM || PPC || SANDBOX
select HAVE_BLOCK_DEVICE
+ select DM_MMC if DM
help
This selects MultiMediaCard, Secure Digital and Secure
Digital I/O support.
help
Enable write access to MMC and SD Cards
+config MMC_PWRSEQ
+ bool "HW reset support for eMMC"
+ depends on PWRSEQ
+ help
+ Ths select Hardware reset support aka pwrseq-emmc for eMMC
+ devices.
+
config MMC_BROKEN_CD
bool "Poll for broken card detection case"
help
config DM_MMC
bool "Enable MMC controllers using Driver Model"
depends on DM
+ select BLK
help
This enables the MultiMediaCard (MMC) uclass which supports MMC and
Secure Digital I/O (SDIO) cards. Both removable (SD, micro-SD, etc.)
if MMC
+config MMC_SDHCI_ADMA_HELPERS
+ bool
+
config MMC_SPI
bool "Support for SPI-based MMC controller"
depends on DM_MMC && DM_SPI
This selects support for Synopsys DesignWare Memory Card Interface driver
extensions used in various Synopsys ARC devboards.
+config NEXELL_DWMMC
+ bool "Nexell SD/MMC controller support"
+ depends on ARCH_NEXELL
+ depends on MMC_DW
+ depends on DM_MMC
+ depends on PINCTRL_NEXELL
+ default y
+
config MMC_MESON_GX
bool "Meson GX EMMC controller support"
depends on DM_MMC && BLK && ARCH_MESON
config MMC_PCI
bool "Support for MMC controllers on PCI"
+ depends on MMC_SDHCI
help
This selects PCI-based MMC controllers.
If you have an MMC controller on a PCI bus, say Y here.
+config MMC_OCTEONTX
+ bool "Marvell Octeon Multimedia Card Interface support"
+ depends on (ARCH_OCTEON || ARCH_OCTEONTX || ARCH_OCTEONTX2)
+ depends on DM_MMC
+ help
+ This selects the Octeon Multimedia card Interface.
+ If you have an OcteonTX/TX2 or MIPS Octeon board with a
+ Multimedia Card slot, say Y here.
+
+ If unsure, say N.
+
+config MVEBU_MMC
+ bool "Kirkwood MMC controller support"
+ depends on DM_MMC && BLK && ARCH_KIRKWOOD
+ help
+ Support for MMC host controller on Kirkwood SoCs.
+ If you are on a Kirkwood architecture, say Y here.
+
+ If unsure, say N.
+
+config PXA_MMC_GENERIC
+ bool "Support for MMC controllers on PXA"
+ help
+ This selects MMC controllers on PXA.
+ If you are on a PXA architecture, say Y here.
+
If unsure, say N.
config MMC_OMAP_HS
config MMC_SDHCI_ADMA
bool "Support SDHCI ADMA2"
depends on MMC_SDHCI
+ select MMC_SDHCI_ADMA_HELPERS
help
This enables support for the ADMA (Advanced DMA) defined
in the SD Host Controller Standard Specification Version 3.00
config SPL_MMC_SDHCI_ADMA
bool "Support SDHCI ADMA2 in SPL"
depends on MMC_SDHCI
+ select MMC_SDHCI_ADMA_HELPERS
help
This enables support for the ADMA (Advanced DMA) defined
in the SD Host Controller Standard Specification Version 3.00 in SPL.
depends on MMC_SDHCI
depends on DM_MMC && OF_CONTROL && BLK
depends on REGMAP
+ select MMC_SDHCI_IO_ACCESSORS
help
Support for Secure Digital Host Controller Interface (SDHCI)
controllers present on TI's AM654 SOCs.
If unsure, say N.
+config MMC_SDHCI_F_SDH30
+ bool "SDHCI support for Fujitsu Semiconductor F_SDH30"
+ depends on BLK && DM_MMC
+ depends on MMC_SDHCI
+ help
+ This selects the Secure Digital Host Controller Interface (SDHCI)
+ Needed by some Fujitsu SoC for MMC / SD / SDIO support.
+ If you have a controller with this interface, say Y or M here.
+ If unsure, say N.
+
config MMC_SDHCI_KONA
bool "SDHCI support on Broadcom KONA platform"
depends on MMC_SDHCI
config MMC_SDHCI_ZYNQ
bool "Arasan SDHCI controller support"
- depends on ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL
depends on DM_MMC && OF_CONTROL && BLK
depends on MMC_SDHCI
help
bool
depends on MMC_SUNXI
+config MMC_PITON
+ bool "MMC support for OpenPiton SoC"
+ depends on DM_MMC && BLK
+ help
+ This selects support for the SD host controller on OpenPiton SoC.
+ Note that this SD controller directly exposes the contents of the
+ SD card as memory mapped, so there is no manual configuration
+ required
+
config GENERIC_ATMEL_MCI
bool "Atmel Multimedia Card Interface support"
depends on DM_MMC && BLK && ARCH_AT91
This selects support for the eSDHC (Enhanced Secure Digital Host
Controller) found on numerous Freescale/NXP SoCs.
+config FSL_ESDHC_SUPPORT_ADMA2
+ bool "enable ADMA2 support"
+ depends on FSL_ESDHC
+ select MMC_SDHCI_ADMA_HELPERS
+ help
+ This enables support for the ADMA2 transfer mode. If supported by the
+ eSDHC it will allow 64bit DMA addresses.
+
config FSL_ESDHC_33V_IO_RELIABILITY_WORKAROUND
bool "enable eSDHC workaround for 3.3v IO reliability issue"
depends on FSL_ESDHC && DM_MMC
This option assumes no hotplug, and u-boot has to make all the way to
to linux to use 1.8v UHS-I speed mode if has card.
+config FSL_ESDHC_VS33_NOT_SUPPORT
+ bool "3.3V power supply not supported"
+ depends on FSL_ESDHC
+ help
+ For eSDHC, power supply is through peripheral circuit. 3.3V support is
+ common. Select this if 3.3V power supply not supported.
+
config FSL_ESDHC_IMX
bool "Freescale/NXP i.MX eSDHC controller support"
help
config FSL_USDHC
bool "Freescale/NXP i.MX uSDHC controller support"
- depends on MX6 || MX7 ||ARCH_MX7ULP || IMX8 || IMX8M || IMXRT || TARGET_S32V234EVB
+ depends on MX6 || MX7 ||ARCH_MX7ULP || IMX8 || IMX8M || IMX8ULP || IMXRT
select FSL_ESDHC_IMX
help
This enables the Ultra Secured Digital Host Controller enhancements
config SYS_FSL_ERRATUM_ESDHC_A001
bool
+
+config SYS_FSL_ERRATUM_A011334
+ bool
+
+config SYS_FSL_ESDHC_UNRELIABLE_PULSE_DETECTION_WORKAROUND
+ bool
projects / J-u-boot.git / blobdiff