+// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2011 - 2013 CompuLab, Ltd. <www.compulab.co.il>
*
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
+#include <env.h>
+#include <init.h>
#include <status_led.h>
#include <netdev.h>
#include <net.h>
#include <i2c.h>
#include <usb.h>
#include <mmc.h>
-#include <nand.h>
+#include <splash.h>
#include <twl4030.h>
-#include <bmp_layout.h>
#include <linux/compiler.h>
#include <asm/io.h>
+#include <linux/errno.h>
#include <asm/arch/mem.h>
#include <asm/arch/mux.h>
#include <asm/arch/mmc_host_def.h>
"NAND",
};
-static u32 gpmc_net_config[GPMC_MAX_REG] = {
- NET_GPMC_CONFIG1,
- NET_GPMC_CONFIG2,
- NET_GPMC_CONFIG3,
- NET_GPMC_CONFIG4,
- NET_GPMC_CONFIG5,
- NET_GPMC_CONFIG6,
- 0
-};
-
-#ifdef CONFIG_LCD
-#ifdef CONFIG_CMD_NAND
-static int splash_load_from_nand(u32 bmp_load_addr)
-{
- struct bmp_header *bmp_hdr;
- int res, splash_screen_nand_offset = 0x100000;
- size_t bmp_size, bmp_header_size = sizeof(struct bmp_header);
-
- if (bmp_load_addr + bmp_header_size >= gd->start_addr_sp)
- goto splash_address_too_high;
-
- res = nand_read_skip_bad(&nand_info[nand_curr_device],
- splash_screen_nand_offset, &bmp_header_size,
- NULL, nand_info[nand_curr_device].size,
- (u_char *)bmp_load_addr);
- if (res < 0)
- return res;
-
- bmp_hdr = (struct bmp_header *)bmp_load_addr;
- bmp_size = le32_to_cpu(bmp_hdr->file_size);
-
- if (bmp_load_addr + bmp_size >= gd->start_addr_sp)
- goto splash_address_too_high;
-
- return nand_read_skip_bad(&nand_info[nand_curr_device],
- splash_screen_nand_offset, &bmp_size,
- NULL, nand_info[nand_curr_device].size,
- (u_char *)bmp_load_addr);
-
-splash_address_too_high:
- printf("Error: splashimage address too high. Data overwrites U-Boot "
- "and/or placed beyond DRAM boundaries.\n");
-
- return -1;
-}
-#else
-static inline int splash_load_from_nand(void)
-{
- return -1;
-}
-#endif /* CONFIG_CMD_NAND */
-
#ifdef CONFIG_SPL_BUILD
/*
* Routine: get_board_mem_timings
}
#endif
+struct splash_location splash_locations[] = {
+ {
+ .name = "nand",
+ .storage = SPLASH_STORAGE_NAND,
+ .flags = SPLASH_STORAGE_RAW,
+ .offset = 0x100000,
+ },
+};
+
int splash_screen_prepare(void)
{
- char *env_splashimage_value;
- u32 bmp_load_addr;
-
- env_splashimage_value = getenv("splashimage");
- if (env_splashimage_value == NULL)
- return -1;
-
- bmp_load_addr = simple_strtoul(env_splashimage_value, 0, 16);
- if (bmp_load_addr == 0) {
- printf("Error: bad splashimage address specified\n");
- return -1;
- }
-
- return splash_load_from_nand(bmp_load_addr);
+ return splash_source_load(splash_locations,
+ ARRAY_SIZE(splash_locations));
}
-#endif /* CONFIG_LCD */
/*
* Routine: board_init
/* boot param addr */
gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
- status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
+#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
+ status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON);
#endif
return 0;
*/
u32 get_board_rev(void)
{
- return cl_eeprom_get_board_rev();
+ return cl_eeprom_get_board_rev(CONFIG_SYS_I2C_EEPROM_BUS);
};
int misc_init_r(void)
{
cl_print_pcb_info();
- dieid_num_r();
+ omap_die_id_display();
return 0;
}
cm_t3730_set_muxconf();
}
-#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_MMC)
#define SB_T35_WP_GPIO 59
int board_mmc_getcd(struct mmc *mmc)
}
#endif
-/*
- * Routine: setup_net_chip_gmpc
- * Description: Setting up the configuration GPMC registers specific to the
- * Ethernet hardware.
- */
-static void setup_net_chip_gmpc(void)
+#if defined(CONFIG_MMC)
+void board_mmc_power_init(void)
{
- struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
-
- enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[5],
- CM_T3X_SMC911X_BASE, GPMC_SIZE_16M);
- enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[4],
- SB_T35_SMC911X_BASE, GPMC_SIZE_16M);
-
- /* Enable off mode for NWE in PADCONF_GPMC_NWE register */
- writew(readw(&ctrl_base->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
-
- /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
- writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
-
- /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
- writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
- &ctrl_base->gpmc_nadv_ale);
+ twl4030_power_mmc_init(0);
}
+#endif
-#ifdef CONFIG_SYS_I2C_OMAP34XX
+#ifdef CONFIG_SYS_I2C_OMAP24XX
/*
* Routine: reset_net_chip
* Description: reset the Ethernet controller via TPS65930 GPIO
*/
-static void reset_net_chip(void)
+static int cm_t3x_reset_net_chip(int gpio)
{
/* Set GPIO1 of TPS65930 as output */
twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x03,
twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x0C,
0x02);
mdelay(1);
+ return 0;
}
#else
-static inline void reset_net_chip(void) {}
+static inline int cm_t3x_reset_net_chip(int gpio) { return 0; }
#endif
#ifdef CONFIG_SMC911X
unsigned char enetaddr[6];
int rc;
- rc = eth_getenv_enetaddr("ethaddr", enetaddr);
+ rc = eth_env_get_enetaddr("ethaddr", enetaddr);
if (rc)
return 0;
- rc = cl_eeprom_read_mac_addr(enetaddr);
+ rc = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS);
if (rc)
return rc;
- if (!is_valid_ether_addr(enetaddr))
+ if (!is_valid_ethaddr(enetaddr))
return -1;
- return eth_setenv_enetaddr("ethaddr", enetaddr);
+ return eth_env_set_enetaddr("ethaddr", enetaddr);
}
-
/*
* Routine: board_eth_init
* Description: initialize module and base-board Ethernet chips
*/
+#define SB_T35_SMC911X_BASE (CONFIG_SMC911X_BASE + SZ_16M)
int board_eth_init(bd_t *bis)
{
int rc = 0, rc1 = 0;
- setup_net_chip_gmpc();
- reset_net_chip();
-
rc1 = handle_mac_address();
if (rc1)
printf("No MAC address found! ");
- rc1 = smc911x_initialize(0, CM_T3X_SMC911X_BASE);
+ rc1 = cl_omap3_smc911x_init(0, 5, CONFIG_SMC911X_BASE,
+ cm_t3x_reset_net_chip, -EINVAL);
if (rc1 > 0)
rc++;
- rc1 = smc911x_initialize(1, SB_T35_SMC911X_BASE);
+ rc1 = cl_omap3_smc911x_init(1, 4, SB_T35_SMC911X_BASE, NULL, -EINVAL);
if (rc1 > 0)
rc++;
}
#endif
-void __weak get_board_serial(struct tag_serialnr *serialnr)
-{
- /*
- * This corresponds to what happens when we can communicate with the
- * eeprom but don't get a valid board serial value.
- */
- serialnr->low = 0;
- serialnr->high = 0;
-};
-
#ifdef CONFIG_USB_EHCI_OMAP
struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
#define SB_T35_USB_HUB_RESET_GPIO 167
int ehci_hcd_init(int index, enum usb_init_type init,
- struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+ struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
u8 val;
int offset;
- if (gpio_request(SB_T35_USB_HUB_RESET_GPIO, "SB-T35 usb hub reset")) {
- printf("Error: can't obtain GPIO %d for SB-T35 usb hub reset",
- SB_T35_USB_HUB_RESET_GPIO);
- return -1;
- }
-
- gpio_direction_output(SB_T35_USB_HUB_RESET_GPIO, 0);
- udelay(10);
- gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
- udelay(1000);
+ cl_usb_hub_init(SB_T35_USB_HUB_RESET_GPIO, "sb-t35 hub rst");
offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_GPIODATADIR1;
twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, offset, &val);
int ehci_hcd_stop(void)
{
+ cl_usb_hub_deinit(SB_T35_USB_HUB_RESET_GPIO);
return omap_ehci_hcd_stop();
}
#endif /* CONFIG_USB_EHCI_OMAP */
projects / J-u-boot.git / blobdiff