arm: xea: defconfig: Define space for redundant envs in SPI-NOR flash

[J-u-boot.git] / README

diff --git a/README b/README
index 107e67fdda5ae38211edb487e24dddf381f46879..8cfa92fac9e54eedf72c1dd0f5a325f61297c12c 100644 (file)
--- a/README
+++ b/README
@@ -2460,7 +2460,7 @@ typically in board_init_f() and board_init_r().
 Configuration Settings:
 -----------------------
 
-- CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
+- MEM_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
                Optionally it can be defined to support 64-bit memory commands.
 
 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
@@ -2870,32 +2870,6 @@ Low Level (hardware related) configuration options:
                If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
                forced to a value that ensures that CCSR is not relocated.
 
-- Floppy Disk Support:
-               CONFIG_SYS_FDC_DRIVE_NUMBER
-
-               the default drive number (default value 0)
-
-               CONFIG_SYS_ISA_IO_STRIDE
-
-               defines the spacing between FDC chipset registers
-               (default value 1)
-
-               CONFIG_SYS_ISA_IO_OFFSET
-
-               defines the offset of register from address. It
-               depends on which part of the data bus is connected to
-               the FDC chipset. (default value 0)
-
-               If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
-               CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
-               default value.
-
-               if CONFIG_SYS_FDC_HW_INIT is defined, then the function
-               fdc_hw_init() is called at the beginning of the FDC
-               setup. fdc_hw_init() must be provided by the board
-               source code. It is used to make hardware-dependent
-               initializations.
-
 - CONFIG_IDE_AHB:
                Most IDE controllers were designed to be connected with PCI
                interface. Only few of them were designed for AHB interface.
@@ -3051,7 +3025,7 @@ Low Level (hardware related) configuration options:
                Add the "loopw" memory command. This only takes effect if
                the memory commands are activated globally (CONFIG_CMD_MEMORY).
 
-- CONFIG_MX_CYCLIC
+- CONFIG_CMD_MX_CYCLIC
                Add the "mdc" and "mwc" memory commands. These are cyclic
                "md/mw" commands.
                Examples:
@@ -3082,14 +3056,16 @@ Low Level (hardware related) configuration options:
                instruction cache) is still performed.
 
 - CONFIG_SPL_BUILD
-               Modifies the behaviour of start.S when compiling a loader
-               that is executed before the actual U-Boot. E.g. when
-               compiling a NAND SPL.
+               Set when the currently-running compilation is for an artifact
+               that will end up in the SPL (as opposed to the TPL or U-Boot
+               proper). Code that needs stage-specific behavior should check
+               this.
 
 - CONFIG_TPL_BUILD
-               Modifies the behaviour of start.S  when compiling a loader
-               that is executed after the SPL and before the actual U-Boot.
-               It is loaded by the SPL.
+               Set when the currently-running compilation is for an artifact
+               that will end up in the TPL (as opposed to the SPL or U-Boot
+               proper). Code that needs stage-specific behavior should check
+               this.
 
 - CONFIG_SYS_MPC85XX_NO_RESETVEC
                Only for 85xx systems. If this variable is specified, the section
@@ -3306,7 +3282,7 @@ Testing of U-Boot Modifications, Ports to New Hardware, etc.:
 If you have modified U-Boot sources (for instance added a new board
 or support for new devices, a new CPU, etc.) you are expected to
 provide feedback to the other developers. The feedback normally takes
-the form of a "patch", i. e. a context diff against a certain (latest
+the form of a "patch", i.e. a context diff against a certain (latest
 official or latest in the git repository) version of U-Boot sources.
 
 But before you submit such a patch, please verify that your modifi-