#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_BUBINGA 1 /* ...on a BUBINGA board */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME bubinga
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
* supported for backward compatibility.
*/
#if 1
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#else
-#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
+#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#endif
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=bubinga\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/bubinga/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff80000\0" \
"ramdisk_addr=fff90000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/bubinga/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-/*
- * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
+ * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
* The Linux BASE_BAUD define should match this configuration.
* baseBaud = cpuClock/(uartDivisor*16)
- * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
* set Linux BASE_BAUD to 403200.
*/
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
-#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
-#define CFG_BASE_BAUD 691200
-
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
+#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
+#define CONFIG_SYS_BASE_BAUD 691200
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
+#define CONFIG_SYS_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
#if defined(CONFIG_CMD_EEPROM)
-#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C boot EEPROM (24C02W) */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* I2C boot EEPROM (24C02W) */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
#endif
/*-----------------------------------------------------------------------
/* resource configuration */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-#define CFG_PCI_CLASSCODE 0x0600 /* PCI Class Code: bridge/host */
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
-#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
+#define CONFIG_SYS_PCI_CLASSCODE 0x0600 /* PCI Class Code: bridge/host */
+#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
+#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
+#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* External peripheral base address
*-----------------------------------------------------------------------
*/
-#define CFG_KEY_REG_BASE_ADDR 0xF0100000
-#define CFG_IR_REG_BASE_ADDR 0xF0200000
-#define CFG_FPGA_REG_BASE_ADDR 0xF0300000
+#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000
+#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000
+#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_SRAM_BASE 0xFFF00000
-#define CFG_FLASH_BASE 0xFFF80000
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_SRAM_BASE 0xFFF00000
+#define CONFIG_SYS_FLASH_BASE 0xFFF80000
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_ADDR0 0x5555
-#define CFG_FLASH_ADDR1 0x2aaa
-#define CFG_FLASH_WORD_SIZE unsigned char
+#define CONFIG_SYS_FLASH_ADDR0 0x5555
+#define CONFIG_SYS_FLASH_ADDR1 0x2aaa
+#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#endif /* CFG_ENV_IS_IN_FLASH */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
/*-----------------------------------------------------------------------
* NVRAM organization
*/
-#define CFG_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 0x1ff8 /* NVRAM size */
+#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
+#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */
-#ifdef CFG_ENV_IS_IN_NVRAM
-#define CFG_ENV_SIZE 0x0ff8 /* Size of Environment vars */
-#define CFG_ENV_ADDR \
- (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
+#ifdef CONFIG_ENV_IS_IN_NVRAM
+#define CONFIG_ENV_SIZE 0x0ff8 /* Size of Environment vars */
+#define CONFIG_ENV_ADDR \
+ (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
#endif
/*
* BR0/1 and OR0/1 (FLASH)
*/
-#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CONFIG_SYS_TEMP_STACK_OCM 1
/* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR 0xF8000000
-#define CFG_OCM_DATA_SIZE 0x1000
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
-#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
+#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/
/* Memory Bank 0 (Flash/SRAM) initialization */
-#define CFG_EBC_PB0AP 0x04006000
-#define CFG_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB0AP 0x04006000
+#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */
/* Memory Bank 1 (NVRAM/RTC) initialization */
-#define CFG_EBC_PB1AP 0x04041000
-#define CFG_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB1AP 0x04041000
+#define CONFIG_SYS_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
/* Memory Bank 2 (not used) initialization */
-#define CFG_EBC_PB2AP 0x00000000
-#define CFG_EBC_PB2CR 0x00000000
+#define CONFIG_SYS_EBC_PB2AP 0x00000000
+#define CONFIG_SYS_EBC_PB2CR 0x00000000
/* Memory Bank 2 (not used) initialization */
-#define CFG_EBC_PB3AP 0x00000000
-#define CFG_EBC_PB3CR 0x00000000
+#define CONFIG_SYS_EBC_PB3AP 0x00000000
+#define CONFIG_SYS_EBC_PB3CR 0x00000000
/* Memory Bank 4 (FPGA regs) initialization */
-#define CFG_EBC_PB4AP 0x01815000
-#define CFG_EBC_PB4CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB4AP 0x01815000
+#define CONFIG_SYS_EBC_PB4CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
/*-----------------------------------------------------------------------
* Definitions for Serial Presence Detect EEPROM address
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
-#define CFG_GPIO0_OSRH 0x55555555
-#define CFG_GPIO0_OSRL 0x40000110
-#define CFG_GPIO0_ISR1H 0x00000000
-#define CFG_GPIO0_ISR1L 0x15555445
-#define CFG_GPIO0_TSRH 0x00000000
-#define CFG_GPIO0_TSRL 0x00000000
-#define CFG_GPIO0_TCR 0xFFFF8014
+#define CONFIG_SYS_GPIO0_OSRH 0x55555555
+#define CONFIG_SYS_GPIO0_OSRL 0x40000110
+#define CONFIG_SYS_GPIO0_ISR1H 0x00000000
+#define CONFIG_SYS_GPIO0_ISR1L 0x15555445
+#define CONFIG_SYS_GPIO0_TSRH 0x00000000
+#define CONFIG_SYS_GPIO0_TSRL 0x00000000
+#define CONFIG_SYS_GPIO0_TCR 0xFFFF8014
/*-----------------------------------------------------------------------
* Some BUBINGA stuff...
#define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */
#define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
projects / J-u-boot.git / blobdiff