*
* Configuration settings for the MX31ADS Freescale board.
*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#include <asm/arch/imx-regs.h>
/* High Level Configuration Options */
-#define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */
-#define CONFIG_MX31 1 /* in a mx31 */
-#define CONFIG_MX31_HCLK_FREQ 26000000 /* RedBoot says 26MHz */
-#define CONFIG_MX31_CLK32 32768
+#define CONFIG_MX31 1 /* This is a mx31 */
+
+#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_SYS_TEXT_BASE 0xA0000000
+
+#define CONFIG_MACH_TYPE MACH_TYPE_MX31ADS
+
/*
* Disabled for now due to build problems under Debian and a significant increase
* in the final file size: 144260 vs. 109536 Bytes.
* Hardware drivers
*/
-#define CONFIG_MXC_UART 1
-#define CONFIG_SYS_MX31_UART1 1
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
#define CONFIG_HARD_SPI 1
#define CONFIG_MXC_SPI 1
#define CONFIG_DEFAULT_SPI_BUS 1
#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_MXC_GPIO
-#define CONFIG_FSL_PMIC
+/* PMIC Controller */
+#define CONFIG_POWER
+#define CONFIG_POWER_SPI
+#define CONFIG_POWER_FSL
#define CONFIG_FSL_PMIC_BUS 1
#define CONFIG_FSL_PMIC_CS 0
#define CONFIG_FSL_PMIC_CLK 1000000
#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
-#define CONFIG_RTC_MC13783 1
+#define CONFIG_FSL_PMIC_BITLEN 32
+#define CONFIG_RTC_MC13XXX
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/***********************************************************
* Command definition
***********************************************************/
-
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SPI
"cp.b ${loadaddr} ${uboot_addr} ${filesize}; " \
"setenv filesize; saveenv\0"
-#define CONFIG_NET_MULTI
#define CONFIG_CS8900
#define CONFIG_CS8900_BASE 0xb4020300
#define CONFIG_CS8900_BUS16 1 /* follow the Linux driver */
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> "
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_HZ 1000
-
#define CONFIG_CMDLINE_EDITING 1
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 CSD0_BASE
#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
+#define CONFIG_BOARD_EARLY_INIT_F
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_GBL_DATA_OFFSET)
/*-----------------------------------------------------------------------
* FLASH and environment organization
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256KiB */
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE (32 * 1024)
+#define CONFIG_ENV_SECT_SIZE (128 * 1024)
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-/* S29WS256N NOR flash has 4 32KiB small sectors at the beginning and at the end.
- * The rest of 32MiB is in 128KiB big sectors. U-Boot occupies the low 4 sectors,
- * if we put environment next to it, we will have to occupy 128KiB for it.
- * Putting it at the top of flash we use only 32KiB. */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_ENV_SECT_SIZE)
/*-----------------------------------------------------------------------
* CFI FLASH driver setup
projects / J-u-boot.git / blobdiff