- i386 Files specific to i386 CPUs
- ixp Files specific to Intel XScale IXP CPUs
- mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
+ - mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
- mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
- mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
+ - mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
- mips Files specific to MIPS CPUs
- mpc5xx Files specific to Freescale MPC5xx CPUs
- mpc5xxx Files specific to Freescale MPC5xxx CPUs
- Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
- CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
- Define exactly one of
- CONFIG_ATSTK1002
-
+ Define exactly one, e.g. CONFIG_ATSTK1002
- CPU Module Type: (if CONFIG_COGENT is defined)
Define exactly one of
CONFIG_OF_LIBFDT
* New libfdt-based support
* Adds the "fdt" command
- * The bootm command does _not_ modify the fdt
+ * The bootm command automatically updates the fdt
CONFIG_OF_FLAT_TREE
* Deprecated, see CONFIG_OF_LIBFDT
* The environment variable "disable_of", when set,
disables this functionality.
- CONFIG_OF_FLAT_TREE_MAX_SIZE
-
- The maximum size of the constructed OF tree.
-
OF_CPU - The proper name of the cpus node.
OF_SOC - The proper name of the soc node.
OF_TBCLK - The timebase frequency.
OF_STDOUT_PATH - The path to the console device
+ boards with QUICC Engines require OF_QE to set UCC mac addresses
+
CONFIG_OF_HAS_BD_T
* CONFIG_OF_LIBFDT - enables the "fdt bd_t" command
CONFIG_OF_HAS_UBOOT_ENV
- * CONFIG_OF_LIBFDT - enables the "fdt bd_t" command
+ * CONFIG_OF_LIBFDT - enables the "fdt env" command
* CONFIG_OF_FLAT_TREE - The resulting flat device tree
will have a copy of u-boot's environment variables
(i.e. setenv videomode 317; saveenv; reset;)
- "videomode=bootargs" all the video parameters are parsed
- from the bootargs. (See drivers/videomodes.c)
+ from the bootargs. (See drivers/video/videomodes.c)
CONFIG_VIDEO_SED13806
CONFIG_FSL_I2C
Define this option if you want to use Freescale's I2C driver in
- drivers/fsl_i2c.c.
+ drivers/i2c/fsl_i2c.c.
- SPI Support: CONFIG_SPI
SPI configuration items (port pins to use, etc). For
an example, see include/configs/sacsng.h.
-- FPGA Support: CONFIG_FPGA_COUNT
+ CONFIG_HARD_SPI
- Specify the number of FPGA devices to support.
+ Enables a hardware SPI driver for general-purpose reads
+ and writes. As with CONFIG_SOFT_SPI, the board configuration
+ must define a list of chip-select function pointers.
+ Currently supported on some MPC8xxx processors. For an
+ example, see include/configs/mpc8349emds.h.
+
+- FPGA Support: CONFIG_FPGA
+
+ Enables FPGA subsystem.
+
+ CONFIG_FPGA_<vendor>
- CONFIG_FPGA
+ Enables support for specific chip vendors.
+ (ALTERA, XILINX)
- Used to specify the types of FPGA devices. For example,
- #define CONFIG_FPGA CFG_XILINX_VIRTEX2
+ CONFIG_FPGA_<family>
+
+ Enables support for FPGA family.
+ (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
+
+ CONFIG_FPGA_COUNT
+
+ Specify the number of FPGA devices to support.
CFG_FPGA_PROG_FEEDBACK
to be a good choice since it makes it far enough from the
start of the data area as well as from the stack pointer.
-Please note that the environment is read-only as long as the monitor
+Please note that the environment is read-only until the monitor
has been relocated to RAM and a RAM copy of the environment has been
created; also, when using EEPROM you will have to use getenv_r()
until then to read environment variables.
enable I2C microcode relocation patch (MPC8xx);
define relocation offset in DPRAM [DSP2]
+- CFG_SMC_UCODE_PATCH, CFG_SMC_DPMEM_OFFSET [0x1FC0]:
+ enable SMC microcode relocation patch (MPC8xx);
+ define relocation offset in DPRAM [SMC1]
+
- CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]:
enable SPI microcode relocation patch (MPC8xx);
define relocation offset in DPRAM [SCC4]
=> setenv ethact SCC ETHERNET
=> ping 10.0.0.1 # traffic sent on SCC ETHERNET
+ ethrotate - When set to "no" U-Boot does not go through all
+ available network interfaces.
+ It just stays at the currently selected interface.
+
netretry - When set to "no" each network operation will
either succeed or fail without retrying.
When set to "once" the network operation will
Useful on scripts which control the retry operation
themselves.
+ npe_ucode - see CONFIG_IXP4XX_NPE_EXT_UCOD
+ if set load address for the npe microcode
+
tftpsrcport - If this is set, the value is used for TFTP's
UDP source port.
For PowerPC, the following registers have specific use:
R1: stack pointer
- R2: TOC pointer
+ R2: reserved for system use
R3-R4: parameter passing and return values
R5-R10: parameter passing
R13: small data area pointer
(U-Boot also uses R14 as internal GOT pointer.)
- ==> U-Boot will use R29 to hold a pointer to the global data
+ ==> U-Boot will use R2 to hold a pointer to the global data
Note: on PPC, we could use a static initializer (since the
address of the global data structure is known at compile time),
average for all boards 752 bytes for the whole U-Boot image,
624 text + 127 data).
+On Blackfin, the normal C ABI (except for P5) is followed as documented here:
+ http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
+
+ ==> U-Boot will use P5 to hold a pointer to the global data
+
On ARM, the following registers are used:
R0: function argument word/integer result
projects / J-u-boot.git / blobdiff