#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define CONFIG_STACKSIZE (256*1024) /* regular stack */
#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
#define CONFIG_SYS_DA850_PLL1_PLLDIV2 0x8001
#define CONFIG_SYS_DA850_PLL1_PLLDIV3 0x8003
-#define CONFIG_SYS_DA850_PLL0_PLLM 24
+#define CONFIG_SYS_DA850_PLL0_PLLM 37
#define CONFIG_SYS_DA850_PLL1_PLLM 21
+/*
+ * DDR2 memory configuration
+ */
+#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
+ DV_DDR_PHY_EXT_STRBEN | \
+ (0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT))
+
+#define CONFIG_SYS_DA850_DDR2_SDBCR ( \
+ (1 << DV_DDR_SDCR_DDR2EN_SHIFT) | \
+ (1 << DV_DDR_SDCR_DDREN_SHIFT) | \
+ (1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \
+ (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \
+ (4 << DV_DDR_SDCR_CL_SHIFT) | \
+ (3 << DV_DDR_SDCR_IBANK_SHIFT) | \
+ (2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
+
+/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
+#define CONFIG_SYS_DA850_DDR2_SDBCR2 0
+
+#define CONFIG_SYS_DA850_DDR2_SDTIMR ( \
+ (19 << DV_DDR_SDTMR1_RFC_SHIFT) | \
+ (1 << DV_DDR_SDTMR1_RP_SHIFT) | \
+ (1 << DV_DDR_SDTMR1_RCD_SHIFT) | \
+ (2 << DV_DDR_SDTMR1_WR_SHIFT) | \
+ (6 << DV_DDR_SDTMR1_RAS_SHIFT) | \
+ (8 << DV_DDR_SDTMR1_RC_SHIFT) | \
+ (1 << DV_DDR_SDTMR1_RRD_SHIFT) | \
+ (1 << DV_DDR_SDTMR1_WTR_SHIFT))
+
+#define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \
+ (7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \
+ (2 << DV_DDR_SDTMR2_XP_SHIFT) | \
+ (0 << DV_DDR_SDTMR2_ODT_SHIFT) | \
+ (10 << DV_DDR_SDTMR2_XSNR_SHIFT) | \
+ (199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \
+ (1 << DV_DDR_SDTMR2_RTP_SHIFT) | \
+ (2 << DV_DDR_SDTMR2_CKE_SHIFT))
+
+#define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000492
+#define CONFIG_SYS_DA850_DDR2_PBBPR 0x30
+
/*
* Serial Driver info
*/
#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_SPI
#ifdef CONFIG_USE_NAND
#undef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
#define CONFIG_ENV_SIZE (128 << 9)
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
#define CONFIG_SYS_NAND_PAGE_2K
-#define CONFIG_SYS_NAND_BUSWIDTH_16_BIT
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
#define CONFIG_SYS_NAND_CS 3
#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
-#define CONFIG_SYS_CLE_MASK 0x10
-#define CONFIG_SYS_ALE_MASK 0x8
+#define CONFIG_SYS_NAND_MASK_CLE 0x10
+#define CONFIG_SYS_NAND_MASK_ALE 0x8
#undef CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
+#define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10)
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_SIZE SZ_512K
+#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
+#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
+ CONFIG_SYS_NAND_U_BOOT_SIZE - \
+ CONFIG_SYS_MALLOC_LEN - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_NAND_ECCPOS { \
+ 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, \
+ 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \
+ 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \
+ 54, 55, 56, 57, 58, 59, 60, 61, 62, 63 }
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 10
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_NAND_LOAD
#endif
#ifdef CONFIG_SYS_USE_NOR
#define CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_SYS_NO_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_ENV_SIZE (64 << 10)
#define CONFIG_ENV_OFFSET (256 << 10)
#define CONFIG_ENV_SECT_SIZE (64 << 10)
-#define CONFIG_SYS_NO_FLASH
#endif
/*
* Network & Ethernet Configuration
*/
#ifdef CONFIG_DRIVER_TI_EMAC
-#define CONFIG_EMAC_MDIO_PHY_NUM 7
#define CONFIG_MII
#undef CONFIG_DRIVER_TI_EMAC_USE_RMII
#define CONFIG_BOOTP_DEFAULT
* U-Boot general configuration
*/
#define CONFIG_MISC_INIT_R
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
+#define CONFIG_BOOTFILE "zImage" /* Boot file name */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
/*
#define CONFIG_CMDLINE_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS "console=ttyS2,115200n8 root=/dev/mmcblk0p2 rw rootwait ip=off"
-#define CONFIG_BOOTCOMMAND "if mmc rescan; then if fatload mmc 0 0xc0600000 boot.scr; then source 0xc0600000; else fatload mmc 0 0xc0700000 uImage; bootm c0700000; fi; else sf probe 0; sf read 0xc0700000 0x80000 0x220000; bootm 0xc0700000; fi"
+#define CONFIG_BOOTCOMMAND \
+ "run envboot; " \
+ "run mmcboot; "
+
+#define DEFAULT_LINUX_BOOT_ENV \
+ "loadaddr=0xc0700000\0" \
+ "fdtaddr=0xc0600000\0" \
+ "scriptaddr=0xc0600000\0"
+
+#include <environment/ti/mmc.h>
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ DEFAULT_LINUX_BOOT_ENV \
+ DEFAULT_MMC_TI_ARGS \
+ "bootpart=0:2\0" \
+ "bootdir=/boot\0" \
+ "bootfile=zImage\0" \
+ "fdtfile=da850-lcdk.dtb\0" \
+ "boot_fdt=yes\0" \
+ "boot_fit=0\0" \
+ "console=ttyS2,115200n8\0"
/*
* U-Boot commands
*/
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_SAVES
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#define CONFIG_CMD_UBIFS
#endif
-#ifdef CONFIG_USE_SPIFLASH
-#endif
-
#if !defined(CONFIG_USE_NAND) && \
!defined(CONFIG_SYS_USE_NOR) && \
!defined(CONFIG_USE_SPIFLASH)
#define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_SIZE (16 << 10)
-#undef CONFIG_CMD_ENV
#endif
/* SD/MMC */
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_DAVINCI_MMC
-
#ifdef CONFIG_MMC
-#define CONFIG_DOS_PARTITION
#undef CONFIG_ENV_IS_IN_MMC
#endif
#ifndef CONFIG_DIRECT_NOR_BOOT
/* defines for SPL */
#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \
CONFIG_SYS_MALLOC_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
projects / J-u-boot.git / blobdiff