sata: Rearrange Kconfig for SATA

[J-u-boot.git] / configs / ls1046aqds_nand_defconfig

diff --git a/configs/ls1046aqds_nand_defconfig b/configs/ls1046aqds_nand_defconfig
index 8168b6e585f8da4557105f2d3b34c503089d8b15..e0e736fa8bbb518b6682bd6e7ce08f6900956b06 100644 (file)
--- a/configs/ls1046aqds_nand_defconfig
+++ b/configs/ls1046aqds_nand_defconfig
@@ -1,6 +1,9 @@
 CONFIG_ARM=y
 CONFIG_TARGET_LS1046AQDS=y
 CONFIG_SYS_TEXT_BASE=0x82000000
+CONFIG_SYS_MALLOC_LEN=0x102000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_NR_DRAM_BANKS=2
 CONFIG_SYS_MEMTEST_START=0x80000000
 CONFIG_SYS_MEMTEST_END=0x9fffffff
@@ -10,18 +13,25 @@ CONFIG_SYS_I2C_MXC_I2C1=y
 CONFIG_SYS_I2C_MXC_I2C2=y
 CONFIG_SYS_I2C_MXC_I2C3=y
 CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_SYS_MALLOC_LEN=0x102000
 CONFIG_DM_GPIO=y
 CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart"
 CONFIG_SPL_TEXT_BASE=0x10000000
 CONFIG_FSL_USE_PCA9547_MUX=y
+CONFIG_VID=y
+CONFIG_VID_FLS_ENV="ls1046aqds_vdd_mv"
+CONFIG_VOL_MONITOR_INA220=y
+CONFIG_VOL_MONITOR_IR36021_SET=y
 CONFIG_FSL_LS_PPA=y
 CONFIG_SPL_SERIAL=y
+CONFIG_SPL_DRIVERS_MISC=y
 CONFIG_SPL=y
 CONFIG_AHCI=y
 CONFIG_DISTRO_DEFAULTS=y
+CONFIG_REMAKE_ELF=y
+CONFIG_MP=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
+CONFIG_DYNAMIC_SYS_CLK_FREQ=y
 CONFIG_RAMBOOT_PBL=y
 CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1046aqds/ls1046aqds_pbi.cfg"
 CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg"
@@ -29,13 +39,17 @@ CONFIG_NAND_BOOT=y
 CONFIG_BOOTDELAY=10
 CONFIG_USE_BOOTARGS=y
 CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:4m(nand_uboot),36m(nand_kernel),472m(nand_free);spi0.0:2m(uboot),14m(free)"
-# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_BOOTCOMMAND="run distro_bootcmd; run nand_bootcmd; env exists secureboot && esbc_halt;;"
 CONFIG_MISC_INIT_R=y
 CONFIG_SPL_FSL_PBL=y
 CONFIG_SPL_BOARD_INIT=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x110
+CONFIG_SPL_ENV_SUPPORT=y
+CONFIG_SPL_I2C=y
 CONFIG_SPL_MPC8XXX_INIT_DDR=y
+CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SPL_WATCHDOG=y
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_IMLS=y
 CONFIG_CMD_GREPENV=y
@@ -50,18 +64,19 @@ CONFIG_CMD_NAND=y
 CONFIG_CMD_PCI=y
 CONFIG_CMD_USB=y
 CONFIG_CMD_CACHE=y
-CONFIG_MP=y
 CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:4m(nand_uboot),36m(nand_kernel),472m(nand_free);spi0.0:2m(uboot),14m(free)"
 CONFIG_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_DM=y
+CONFIG_SATA=y
 CONFIG_SATA_CEVA=y
 CONFIG_FSL_CAAM=y
 CONFIG_DYNAMIC_DDR_CLK_FREQ=y
 CONFIG_DDR_ECC=y
 CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
+CONFIG_MPC8XXX_GPIO=y
 CONFIG_DM_I2C=y
 CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
 CONFIG_SYS_I2C_EEPROM_ADDR=0x57
@@ -71,17 +86,22 @@ CONFIG_MTD_NOR_FLASH=y
 CONFIG_FLASH_CFI_DRIVER=y
 CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
 CONFIG_SYS_FLASH_CFI=y
+CONFIG_SYS_MAX_FLASH_BANKS=2
 CONFIG_NAND_FSL_IFC=y
 CONFIG_SYS_NAND_ONFI_DETECTION=y
 CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
 CONFIG_SYS_NAND_U_BOOT_OFFS=0x40000
 CONFIG_SF_DEFAULT_BUS=1
+CONFIG_SPI_FLASH_EON=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
 CONFIG_PHYLIB=y
 CONFIG_PHYLIB_10G=y
 CONFIG_PHY_REALTEK=y
 CONFIG_PHY_VITESSE=y
 CONFIG_E1000=y
 CONFIG_FMAN_ENET=y
+CONFIG_SYS_FMAN_FW_ADDR=0x900000
 CONFIG_NVME=y
 CONFIG_PCI=y
 CONFIG_DM_PCI_COMPAT=y
@@ -96,4 +116,3 @@ CONFIG_FSL_DSPI=y
 CONFIG_USB=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_DWC3=y
-CONFIG_EFI_LOADER_BOUNCE_BUFFER=y