/*
- * (C) Copyright 2006
+ * (C) Copyright 2006-2007
*
* Configuation settings for the PDNB3 board.
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR 18 /* NPE1 PHY address */
#define CONFIG_MII 1 /* MII PHY management */
-#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
/*
* Misc configuration options
#define CONFIG_USE_IRQ 1 /* we need IRQ stuff for timer */
#define CONFIG_BOOTCOUNT_LIMIT /* support for bootcount limit */
-#define CFG_BOOTCOUNT_ADDR 0x60003000 /* inside qmrg sram */
+#define CONFIG_SYS_BOOTCOUNT_ADDR 0x60003000 /* inside qmrg sram */
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (1 << 20)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (1 << 20)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
-#define CFG_IXP425_CONSOLE IXP425_UART1 /* we use UART1 for console */
-
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_DHCP | \
- CFG_CMD_DATE | \
- CFG_CMD_NET | \
- CFG_CMD_MII | \
- CFG_CMD_NAND | \
- CFG_CMD_I2C | \
- CFG_CMD_ELF | \
- CFG_CMD_PING)
-
-/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-/* These are u-boot generic parameters */
-#include <cmd_confdefs.h>
+#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1 /* we use UART1 for console */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_PING
+
+#if !defined(CONFIG_SCPU)
+#define CONFIG_CMD_NAND
+#endif
+
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
-#define CFG_LOAD_ADDR 0x00010000 /* default load address */
-
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
+#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */
+
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Stack sizes
* Default configuration (environment varibles...)
*----------------------------------------------------------------------*/
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
"update=protect off 50000000 5007dfff;era 50000000 5007dfff;" \
"cp.b 100000 50000000 ${filesize};" \
"setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
+ "upd=run load update\0" \
"ipaddr=10.0.0.233\0" \
"serverip=10.0.0.152\0" \
- "netmask=255.255.0.0\0" \
+ "netmask=255.255.0.0\0" \
"ethaddr=c6:6f:13:36:f3:81\0" \
"eth1addr=c6:6f:13:36:f3:82\0" \
"mtdparts=IXP4XX-Flash.0:504k@0(uboot),4k@504k(env)," \
#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
-#define CFG_FLASH_BASE 0x50000000
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (504 << 10) /* Reserve 512 kB for Monitor */
+#define CONFIG_SYS_FLASH_BASE 0x50000000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#if defined(CONFIG_SCPU)
+#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 512 kB for Monitor */
+#else
+#define CONFIG_SYS_MONITOR_LEN (504 << 10) /* Reserve 512 kB for Monitor */
+#endif
/*
* Expansion bus settings
*/
-#define CFG_EXP_CS0 0x94913C43 /* 8bit, max size */
-#define CFG_EXP_CS1 0x85000043 /* 8bit, 512bytes */
+#if defined(CONFIG_SCPU)
+#define CONFIG_SYS_EXP_CS0 0x94d23C42 /* 8bit, max size */
+#else
+#define CONFIG_SYS_EXP_CS0 0x94913C43 /* 8bit, max size */
+#endif
+#define CONFIG_SYS_EXP_CS1 0x85000043 /* 8bit, 512bytes */
/*
* SDRAM settings
*/
-#define CFG_SDR_CONFIG 0x18
-#define CFG_SDR_MODE_CONFIG 0x1
-#define CFG_SDRAM_REFRESH_CNT 0x81a
+#define CONFIG_SYS_SDR_CONFIG 0x18
+#define CONFIG_SYS_SDR_MODE_CONFIG 0x1
+#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a
/*
* FLASH and environment organization
*/
-#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+#if defined(CONFIG_SCPU)
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* no byte writes on IXP4xx */
+#endif
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
+
+#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char /* flash word size (width) */
+#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
+#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
+#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SECT_SIZE 0x1000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN)
-#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
+#if defined(CONFIG_SCPU)
+/* no redundant environment on SCPU */
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#else
+#define CONFIG_ENV_SECT_SIZE 0x1000 /* size of one complete sector */
+#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif
+#if !defined(CONFIG_SCPU)
/*
* NAND-FLASH stuff
*/
-#define CFG_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
-#define CFG_NAND_BASE 0x51000000 /* NAND FLASH Base Address */
+#define CONFIG_SYS_NAND_BASE 0x51000000 /* NAND FLASH Base Address */
+#endif
/*
* GPIO settings
*/
/* FPGA program pin configuration */
-#define CFG_GPIO_PRG 12 /* FPGA program pin (cpu output)*/
-#define CFG_GPIO_CLK 10 /* FPGA clk pin (cpu output) */
-#define CFG_GPIO_DATA 14 /* FPGA data pin (cpu output) */
-#define CFG_GPIO_INIT 13 /* FPGA init pin (cpu input) */
-#define CFG_GPIO_DONE 11 /* FPGA done pin (cpu input) */
+#define CONFIG_SYS_GPIO_PRG 12 /* FPGA program pin (cpu output)*/
+#define CONFIG_SYS_GPIO_CLK 10 /* FPGA clk pin (cpu output) */
+#define CONFIG_SYS_GPIO_DATA 14 /* FPGA data pin (cpu output) */
+#define CONFIG_SYS_GPIO_INIT 13 /* FPGA init pin (cpu input) */
+#define CONFIG_SYS_GPIO_DONE 11 /* FPGA done pin (cpu input) */
/* other GPIO's */
-#define CFG_GPIO_RESTORE_INT 0
-#define CFG_GPIO_RESTART_INT 1
-#define CFG_GPIO_SYS_RUNNING 2
-#define CFG_GPIO_PCI_INTA 3
-#define CFG_GPIO_PCI_INTB 4
-#define CFG_GPIO_I2C_SCL 6
-#define CFG_GPIO_I2C_SDA 7
-#define CFG_GPIO_FPGA_RESET 9
-#define CFG_GPIO_CLK_33M 15
+#define CONFIG_SYS_GPIO_RESTORE_INT 0
+#define CONFIG_SYS_GPIO_RESTART_INT 1
+#define CONFIG_SYS_GPIO_SYS_RUNNING 2
+#define CONFIG_SYS_GPIO_PCI_INTA 3
+#define CONFIG_SYS_GPIO_PCI_INTB 4
+#define CONFIG_SYS_GPIO_I2C_SCL 6
+#define CONFIG_SYS_GPIO_I2C_SDA 7
+#define CONFIG_SYS_GPIO_FPGA_RESET 9
+#define CONFIG_SYS_GPIO_CLK_33M 15
/*
* I2C stuff
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-#define CFG_I2C_SPEED 83000 /* 83 kHz is supposed to work */
-#define CFG_I2C_SLAVE 0xFE
+#define CONFIG_SYS_I2C_SPEED 83000 /* 83 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SLAVE 0xFE
/*
* Software (bit-bang) I2C driver configuration
*/
-#define PB_SCL (1 << CFG_GPIO_I2C_SCL)
-#define PB_SDA (1 << CFG_GPIO_I2C_SDA)
+#define PB_SCL (1 << CONFIG_SYS_GPIO_I2C_SCL)
+#define PB_SDA (1 << CONFIG_SYS_GPIO_I2C_SDA)
-#define I2C_INIT GPIO_OUTPUT_ENABLE(CFG_GPIO_I2C_SCL)
-#define I2C_ACTIVE GPIO_OUTPUT_ENABLE(CFG_GPIO_I2C_SDA)
-#define I2C_TRISTATE GPIO_OUTPUT_DISABLE(CFG_GPIO_I2C_SDA)
+#define I2C_INIT GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_I2C_SCL)
+#define I2C_ACTIVE GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_I2C_SDA)
+#define I2C_TRISTATE GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_I2C_SDA)
#define I2C_READ ((*IXP425_GPIO_GPINR & PB_SDA) != 0)
-#define I2C_SDA(bit) if (bit) GPIO_OUTPUT_SET(CFG_GPIO_I2C_SDA); \
- else GPIO_OUTPUT_CLEAR(CFG_GPIO_I2C_SDA)
-#define I2C_SCL(bit) if (bit) GPIO_OUTPUT_SET(CFG_GPIO_I2C_SCL); \
- else GPIO_OUTPUT_CLEAR(CFG_GPIO_I2C_SCL)
+#define I2C_SDA(bit) if (bit) GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_I2C_SDA); \
+ else GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_I2C_SDA)
+#define I2C_SCL(bit) if (bit) GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_I2C_SCL); \
+ else GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_I2C_SCL)
#define I2C_DELAY udelay(3) /* 1/4 I2C clock duration */
/*
* I2C RTC
*/
+#if 0 /* test-only */
+#define CONFIG_RTC_DS1340 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#else
+/* M41T11 Serial Access Timekeeper(R) SRAM */
#define CONFIG_RTC_M41T11 1
-#define CFG_I2C_RTC_ADDR 0x68
-#define CFG_M41T11_BASE_YEAR 1900 /* play along with the linux driver */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with the linux driver */
+#endif
/*
* Spartan3 FPGA configuration support
*/
-#define CFG_FPGA_MAX_SIZE 700*1024 /* 700kByte for XC3S500E */
+#define CONFIG_SYS_FPGA_MAX_SIZE 700*1024 /* 700kByte for XC3S500E */
-#define CFG_FPGA_PRG (1 << CFG_GPIO_PRG) /* FPGA program pin (cpu output)*/
-#define CFG_FPGA_CLK (1 << CFG_GPIO_CLK) /* FPGA clk pin (cpu output) */
-#define CFG_FPGA_DATA (1 << CFG_GPIO_DATA) /* FPGA data pin (cpu output) */
-#define CFG_FPGA_INIT (1 << CFG_GPIO_INIT) /* FPGA init pin (cpu input) */
-#define CFG_FPGA_DONE (1 << CFG_GPIO_DONE) /* FPGA done pin (cpu input) */
+#define CONFIG_SYS_FPGA_PRG (1 << CONFIG_SYS_GPIO_PRG) /* FPGA program pin (cpu output)*/
+#define CONFIG_SYS_FPGA_CLK (1 << CONFIG_SYS_GPIO_CLK) /* FPGA clk pin (cpu output) */
+#define CONFIG_SYS_FPGA_DATA (1 << CONFIG_SYS_GPIO_DATA) /* FPGA data pin (cpu output) */
+#define CONFIG_SYS_FPGA_INIT (1 << CONFIG_SYS_GPIO_INIT) /* FPGA init pin (cpu input) */
+#define CONFIG_SYS_FPGA_DONE (1 << CONFIG_SYS_GPIO_DONE) /* FPGA done pin (cpu input) */
/*
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 32
+#define CONFIG_SYS_CACHELINE_SIZE 32
#endif /* __CONFIG_H */
projects / J-u-boot.git / blobdiff