This is the size of the bootstage record list and is the maximum
number of bootstage records that can be recorded.
+config TPL_BOOTSTAGE_RECORD_COUNT
+ int "Number of boot stage records to store for TPL"
+ default 5
+ help
+ This is the size of the bootstage record list and is the maximum
+ number of bootstage records that can be recorded.
+
config BOOTSTAGE_FDT
bool "Store boot timing information in the OS device tree"
depends on BOOTSTAGE
This should be large enough to hold the bootstage stash. A value of
4096 (4KiB) is normally plenty.
+config SHOW_BOOT_PROGRESS
+ bool "Show boot progress in a board-specific manner"
+ help
+ Defining this option allows to add some board-specific code (calling
+ a user-provided function show_boot_progress(int) that enables you to
+ show the system's boot progress on some display (for example, some
+ LEDs) on your board. At the moment, the following checkpoints are
+ implemented:
+
+ Legacy uImage format:
+
+ Arg Where When
+ 1 common/cmd_bootm.c before attempting to boot an image
+ -1 common/cmd_bootm.c Image header has bad magic number
+ 2 common/cmd_bootm.c Image header has correct magic number
+ -2 common/cmd_bootm.c Image header has bad checksum
+ 3 common/cmd_bootm.c Image header has correct checksum
+ -3 common/cmd_bootm.c Image data has bad checksum
+ 4 common/cmd_bootm.c Image data has correct checksum
+ -4 common/cmd_bootm.c Image is for unsupported architecture
+ 5 common/cmd_bootm.c Architecture check OK
+ -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
+ 6 common/cmd_bootm.c Image Type check OK
+ -6 common/cmd_bootm.c gunzip uncompression error
+ -7 common/cmd_bootm.c Unimplemented compression type
+ 7 common/cmd_bootm.c Uncompression OK
+ 8 common/cmd_bootm.c No uncompress/copy overwrite error
+ -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
+
+ 9 common/image.c Start initial ramdisk verification
+ -10 common/image.c Ramdisk header has bad magic number
+ -11 common/image.c Ramdisk header has bad checksum
+ 10 common/image.c Ramdisk header is OK
+ -12 common/image.c Ramdisk data has bad checksum
+ 11 common/image.c Ramdisk data has correct checksum
+ 12 common/image.c Ramdisk verification complete, start loading
+ -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
+ 13 common/image.c Start multifile image verification
+ 14 common/image.c No initial ramdisk, no multifile, continue.
+
+ 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
+
+ -30 arch/powerpc/lib/board.c Fatal error, hang the system
+ -31 post/post.c POST test failed, detected by post_output_backlog()
+ -32 post/post.c POST test failed, detected by post_run_single()
+
+ 34 common/cmd_doc.c before loading a Image from a DOC device
+ -35 common/cmd_doc.c Bad usage of "doc" command
+ 35 common/cmd_doc.c correct usage of "doc" command
+ -36 common/cmd_doc.c No boot device
+ 36 common/cmd_doc.c correct boot device
+ -37 common/cmd_doc.c Unknown Chip ID on boot device
+ 37 common/cmd_doc.c correct chip ID found, device available
+ -38 common/cmd_doc.c Read Error on boot device
+ 38 common/cmd_doc.c reading Image header from DOC device OK
+ -39 common/cmd_doc.c Image header has bad magic number
+ 39 common/cmd_doc.c Image header has correct magic number
+ -40 common/cmd_doc.c Error reading Image from DOC device
+ 40 common/cmd_doc.c Image header has correct magic number
+ 41 common/cmd_ide.c before loading a Image from a IDE device
+ -42 common/cmd_ide.c Bad usage of "ide" command
+ 42 common/cmd_ide.c correct usage of "ide" command
+ -43 common/cmd_ide.c No boot device
+ 43 common/cmd_ide.c boot device found
+ -44 common/cmd_ide.c Device not available
+ 44 common/cmd_ide.c Device available
+ -45 common/cmd_ide.c wrong partition selected
+ 45 common/cmd_ide.c partition selected
+ -46 common/cmd_ide.c Unknown partition table
+ 46 common/cmd_ide.c valid partition table found
+ -47 common/cmd_ide.c Invalid partition type
+ 47 common/cmd_ide.c correct partition type
+ -48 common/cmd_ide.c Error reading Image Header on boot device
+ 48 common/cmd_ide.c reading Image Header from IDE device OK
+ -49 common/cmd_ide.c Image header has bad magic number
+ 49 common/cmd_ide.c Image header has correct magic number
+ -50 common/cmd_ide.c Image header has bad checksum
+ 50 common/cmd_ide.c Image header has correct checksum
+ -51 common/cmd_ide.c Error reading Image from IDE device
+ 51 common/cmd_ide.c reading Image from IDE device OK
+ 52 common/cmd_nand.c before loading a Image from a NAND device
+ -53 common/cmd_nand.c Bad usage of "nand" command
+ 53 common/cmd_nand.c correct usage of "nand" command
+ -54 common/cmd_nand.c No boot device
+ 54 common/cmd_nand.c boot device found
+ -55 common/cmd_nand.c Unknown Chip ID on boot device
+ 55 common/cmd_nand.c correct chip ID found, device available
+ -56 common/cmd_nand.c Error reading Image Header on boot device
+ 56 common/cmd_nand.c reading Image Header from NAND device OK
+ -57 common/cmd_nand.c Image header has bad magic number
+ 57 common/cmd_nand.c Image header has correct magic number
+ -58 common/cmd_nand.c Error reading Image from NAND device
+ 58 common/cmd_nand.c reading Image from NAND device OK
+
+ -60 common/env_common.c Environment has a bad CRC, using default
+
+ 64 net/eth.c starting with Ethernet configuration.
+ -64 net/eth.c no Ethernet found.
+ 65 net/eth.c Ethernet found.
+
+ -80 common/cmd_net.c usage wrong
+ 80 common/cmd_net.c before calling net_loop()
+ -81 common/cmd_net.c some error in net_loop() occurred
+ 81 common/cmd_net.c net_loop() back without error
+ -82 common/cmd_net.c size == 0 (File with size 0 loaded)
+ 82 common/cmd_net.c trying automatic boot
+ 83 common/cmd_net.c running "source" command
+ -83 common/cmd_net.c some error in automatic boot or "source" command
+ 84 common/cmd_net.c end without errors
+
+ FIT uImage format:
+
+ Arg Where When
+ 100 common/cmd_bootm.c Kernel FIT Image has correct format
+ -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
+ 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
+ -101 common/cmd_bootm.c Can't get configuration for kernel subimage
+ 102 common/cmd_bootm.c Kernel unit name specified
+ -103 common/cmd_bootm.c Can't get kernel subimage node offset
+ 103 common/cmd_bootm.c Found configuration node
+ 104 common/cmd_bootm.c Got kernel subimage node offset
+ -104 common/cmd_bootm.c Kernel subimage hash verification failed
+ 105 common/cmd_bootm.c Kernel subimage hash verification OK
+ -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
+ 106 common/cmd_bootm.c Architecture check OK
+ -106 common/cmd_bootm.c Kernel subimage has wrong type
+ 107 common/cmd_bootm.c Kernel subimage type OK
+ -107 common/cmd_bootm.c Can't get kernel subimage data/size
+ 108 common/cmd_bootm.c Got kernel subimage data/size
+ -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
+ -109 common/cmd_bootm.c Can't get kernel subimage type
+ -110 common/cmd_bootm.c Can't get kernel subimage comp
+ -111 common/cmd_bootm.c Can't get kernel subimage os
+ -112 common/cmd_bootm.c Can't get kernel subimage load address
+ -113 common/cmd_bootm.c Image uncompress/copy overwrite error
+
+ 120 common/image.c Start initial ramdisk verification
+ -120 common/image.c Ramdisk FIT image has incorrect format
+ 121 common/image.c Ramdisk FIT image has correct format
+ 122 common/image.c No ramdisk subimage unit name, using configuration
+ -122 common/image.c Can't get configuration for ramdisk subimage
+ 123 common/image.c Ramdisk unit name specified
+ -124 common/image.c Can't get ramdisk subimage node offset
+ 125 common/image.c Got ramdisk subimage node offset
+ -125 common/image.c Ramdisk subimage hash verification failed
+ 126 common/image.c Ramdisk subimage hash verification OK
+ -126 common/image.c Ramdisk subimage for unsupported architecture
+ 127 common/image.c Architecture check OK
+ -127 common/image.c Can't get ramdisk subimage data/size
+ 128 common/image.c Got ramdisk subimage data/size
+ 129 common/image.c Can't get ramdisk load address
+ -129 common/image.c Got ramdisk load address
+
+ -130 common/cmd_doc.c Incorrect FIT image format
+ 131 common/cmd_doc.c FIT image format OK
+
+ -140 common/cmd_ide.c Incorrect FIT image format
+ 141 common/cmd_ide.c FIT image format OK
+
+ -150 common/cmd_nand.c Incorrect FIT image format
+ 151 common/cmd_nand.c FIT image format OK
+
endmenu
menu "Boot media"
config NAND_BOOT
bool "Support for booting from NAND flash"
default n
- imply NAND
+ imply MTD_RAW_NAND
help
Enabling this will make a U-Boot binary that is capable of being
booted via NAND flash. This is not a must, some SoCs need this,
config ONENAND_BOOT
bool "Support for booting from ONENAND"
default n
- imply NAND
+ imply MTD_RAW_NAND
help
Enabling this will make a U-Boot binary that is capable of being
booted via ONENAND. This is not a must, some SoCs need this,
config LOGLEVEL
int "loglevel"
default 4
- range 0 8
+ range 0 10
help
All Messages with a loglevel smaller than the console loglevel will
be compiled in. The loglevels are defined as follows:
depends on PRE_CONSOLE_BUFFER
default 0x2f000000 if ARCH_SUNXI && MACH_SUN9I
default 0x4f000000 if ARCH_SUNXI && !MACH_SUN9I
+ default 0x0f000000 if ROCKCHIP_RK3288
+ default 0x0f200000 if ROCKCHIP_RK3399
help
This sets the start address of the pre-console buffer. This must
be in available memory and is accessed before relocation and
discarded if not needed. Logging supports various categories and
levels of severity.
-config SPL_LOG
- bool "Enable logging support in SPL"
- depends on LOG
- help
- This enables support for logging of status and debug messages. These
- can be displayed on the console, recorded in a memory buffer, or
- discarded if not needed. Logging supports various categories and
- levels of severity.
-
-config TPL_LOG
- bool "Enable logging support in TPL"
- depends on LOG
- help
- This enables support for logging of status and debug messages. These
- can be displayed on the console, recorded in a memory buffer, or
- discarded if not needed. Logging supports various categories and
- levels of severity.
+if LOG
config LOG_MAX_LEVEL
int "Maximum log level to record"
- depends on LOG
- default 5
+ default 6
+ range 0 9
help
This selects the maximum log level that will be recorded. Any value
higher than this will be ignored. If possible log statements below
8 - debug content
9 - debug hardware I/O
-config SPL_LOG_MAX_LEVEL
- int "Maximum log level to record in SPL"
- depends on SPL_LOG
- default 3
+config LOG_DEFAULT_LEVEL
+ int "Default logging level to display"
+ default LOG_MAX_LEVEL
+ range 0 LOG_MAX_LEVEL
help
- This selects the maximum log level that will be recorded. Any value
- higher than this will be ignored. If possible log statements below
- this level will be discarded at build time. Levels:
+ This is the default logging level set when U-Boot starts. It can
+ be adjusted later using the 'log level' command. Note that setting
+ this to a value above LOG_MAX_LEVEL will be ineffective, since the
+ higher levels are not compiled in to U-Boot.
0 - emergency
1 - alert
8 - debug content
9 - debug hardware I/O
-config TPL_LOG_MAX_LEVEL
- int "Maximum log level to record in TPL"
- depends on TPL_LOG
+config LOG_CONSOLE
+ bool "Allow log output to the console"
+ default y
+ help
+ Enables a log driver which writes log records to the console.
+ Generally the console is the serial port or LCD display. Only the
+ log message is shown - other details like level, category, file and
+ line number are omitted.
+
+config LOG_SYSLOG
+ bool "Log output to syslog server"
+ depends on NET
+ help
+ Enables a log driver which broadcasts log records via UDP port 514
+ to syslog servers.
+
+config SPL_LOG
+ bool "Enable logging support in SPL"
+ depends on LOG
+ help
+ This enables support for logging of status and debug messages. These
+ can be displayed on the console, recorded in a memory buffer, or
+ discarded if not needed. Logging supports various categories and
+ levels of severity.
+
+if SPL_LOG
+
+config SPL_LOG_MAX_LEVEL
+ int "Maximum log level to record in SPL"
+ depends on SPL_LOG
default 3
+ range 0 9
help
This selects the maximum log level that will be recorded. Any value
higher than this will be ignored. If possible log statements below
8 - debug content
9 - debug hardware I/O
-config LOG_DEFAULT_LEVEL
- int "Default logging level to display"
- default 6
+config SPL_LOG_CONSOLE
+ bool "Allow log output to the console in SPL"
+ default y
help
- This is the default logging level set when U-Boot starts. It can
- be adjusted later using the 'log level' command. Note that setting
- this to a value abnove LOG_MAX_LEVEL will be ineffective, since the
- higher levels are not compiled in to U-Boot.
+ Enables a log driver which writes log records to the console.
+ Generally the console is the serial port or LCD display. Only the
+ log message is shown - other details like level, category, file and
+ line number are omitted.
+
+endif
+
+config TPL_LOG
+ bool "Enable logging support in TPL"
+ depends on LOG
+ help
+ This enables support for logging of status and debug messages. These
+ can be displayed on the console, recorded in a memory buffer, or
+ discarded if not needed. Logging supports various categories and
+ levels of severity.
+
+if TPL_LOG
+
+config TPL_LOG_MAX_LEVEL
+ int "Maximum log level to record in TPL"
+ depends on TPL_LOG
+ default 3
+ range 0 9
+ help
+ This selects the maximum log level that will be recorded. Any value
+ higher than this will be ignored. If possible log statements below
+ this level will be discarded at build time. Levels:
0 - emergency
1 - alert
8 - debug content
9 - debug hardware I/O
-config LOG_CONSOLE
- bool "Allow log output to the console"
- depends on LOG
- default y
- help
- Enables a log driver which writes log records to the console.
- Generally the console is the serial port or LCD display. Only the
- log message is shown - other details like level, category, file and
- line number are omitted.
-
-config SPL_LOG_CONSOLE
- bool "Allow log output to the console in SPL"
- depends on SPL_LOG
- default y
- help
- Enables a log driver which writes log records to the console.
- Generally the console is the serial port or LCD display. Only the
- log message is shown - other details like level, category, file and
- line number are omitted.
-
config TPL_LOG_CONSOLE
- bool "Allow log output to the console in SPL"
- depends on TPL_LOG
+ bool "Allow log output to the console in TPL"
default y
help
Enables a log driver which writes log records to the console.
log message is shown - other details like level, category, file and
line number are omitted.
-config LOG_TEST
- bool "Provide a test for logging"
- depends on LOG
- default y if SANDBOX
- help
- This enables a 'log test' command to test logging. It is normally
- executed from a pytest and simply outputs logging information
- in various different ways to test that the logging system works
- correctly with various settings.
+endif
config LOG_ERROR_RETURN
bool "Log all functions which return an error"
- depends on LOG
help
When an error is returned in U-Boot it is sometimes difficult to
figure out the root cause. For example, reading from SPI flash may
You can add log_ret() to all functions which return an error code.
+config LOG_TEST
+ bool "Provide a test for logging"
+ depends on UNIT_TEST
+ default y if SANDBOX
+ help
+ This enables a 'log test' command to test logging. It is normally
+ executed from a pytest and simply outputs logging information
+ in various different ways to test that the logging system works
+ correctly with various settings.
+
+endif
+
endmenu
config SUPPORT_RAW_INITRD
U-Boot calls last_stage_init() before the command-line interpreter is
started.
+config PCI_INIT_R
+ bool "Enumerate PCI buses during init"
+ depends on PCI
+ default y if !DM_PCI
+ help
+ With this option U-Boot will call pci_init() soon after relocation,
+ which will enumerate PCI buses. This is needed, for instance, in the
+ case of DM PCI-based Ethernet devices, which will not be detected
+ without having the enumeration performed earlier.
+
endmenu
menu "Security support"
default 100
depends on UPDATE_TFTP
+config ANDROID_AB
+ bool "Android A/B updates"
+ default n
+ help
+ If enabled, adds support for the new Android A/B update model. This
+ allows the bootloader to select which slot to boot from based on the
+ information provided by userspace via the Android boot_ctrl HAL. This
+ allows a bootloader to try a new version of the system but roll back
+ to previous version if the new one didn't boot all the way.
+
endmenu
menu "Blob list"
endmenu
source "common/spl/Kconfig"
+
+config IMAGE_SIGN_INFO
+ bool
+ select SHA1
+ select SHA256
+ help
+ Enable image_sign_info helper functions.
+
+if IMAGE_SIGN_INFO
+
+config SPL_IMAGE_SIGN_INFO
+ bool
+ select SHA1
+ select SHA256
+ help
+ Enable image_sign_info helper functions in SPL.
+
+endif
projects / J-u-boot.git / blobdiff