#include <linux/sizes.h>
#include <asm/arch/stm32.h>
-/*
- * Number of clock ticks in 1 sec
- */
-#define CONFIG_SYS_HZ 1000
-
-#ifndef CONFIG_STM32MP1_TRUSTED
+#ifndef CONFIG_TFABOOT
/* PSCI support */
#define CONFIG_ARMV7_PSCI_1_0
#define CONFIG_ARMV7_SECURE_BASE STM32_SYSRAM_BASE
#define CONFIG_SYS_CBSIZE SZ_1K
/*
- * Needed by "loadb"
+ * default load address used for command tftp, bootm , loadb, ...
*/
-#define CONFIG_SYS_LOAD_ADDR STM32_DDR_BASE
-
-#if defined(CONFIG_ENV_IS_IN_SPI_FLASH)
-#define CONFIG_ENV_SECT_SIZE SZ_256K
-#define CONFIG_ENV_OFFSET 0x00280000
-#endif
+#define CONFIG_LOADADDR 0xc2000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
/* ATAGs */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
+/*
+ * For booting Linux, use the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ SZ_256M
+
/* Extend size of kernel image for uncompression */
-#define CONFIG_SYS_BOOTM_LEN SZ_32M
+#define CONFIG_SYS_BOOTM_LEN SZ_32M
/* SPL support */
#ifdef CONFIG_SPL
-/* BOOTROM load address */
/* SPL use DDR */
#define CONFIG_SPL_BSS_START_ADDR 0xC0200000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
#define CONFIG_SPL_STACK (STM32_SYSRAM_BASE + \
STM32_SYSRAM_SIZE)
#endif /* #ifdef CONFIG_SPL */
-
-#define CONFIG_SYS_MEMTEST_START STM32_DDR_BASE
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + SZ_64M)
-#define CONFIG_SYS_MEMTEST_SCRATCH (CONFIG_SYS_MEMTEST_END + 4)
-
/*MMC SD*/
#define CONFIG_SYS_MMC_MAX_DEVICE 3
+/* NAND support */
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+
/* Ethernet need */
#ifdef CONFIG_DWC_ETH_QOS
#define CONFIG_SYS_NONCACHED_MEMORY (1 * SZ_1M) /* 1M */
#define CONFIG_SYS_AUTOLOAD "no"
#endif
+#ifdef CONFIG_DM_VIDEO
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_BMP_16BPP
+#define CONFIG_BMP_24BPP
+#define CONFIG_BMP_32BPP
+#endif
+
/*****************************************************************************/
#ifdef CONFIG_DISTRO_DEFAULTS
/*****************************************************************************/
#if !defined(CONFIG_SPL_BUILD)
-/* NAND support */
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define BOOT_TARGET_DEVICES(func) \
- func(MMC, mmc, 1) \
- func(MMC, mmc, 0) \
- func(MMC, mmc, 2) \
- func(PXE, pxe, na)
+#ifdef CONFIG_CMD_MMC
+#define BOOT_TARGET_MMC0(func) func(MMC, mmc, 0)
+#define BOOT_TARGET_MMC1(func) func(MMC, mmc, 1)
+#define BOOT_TARGET_MMC2(func) func(MMC, mmc, 2)
+#else
+#define BOOT_TARGET_MMC0(func)
+#define BOOT_TARGET_MMC1(func)
+#define BOOT_TARGET_MMC2(func)
+#endif
+
+#ifdef CONFIG_NET
+#define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
+#else
+#define BOOT_TARGET_PXE(func)
+#endif
+
+#ifdef CONFIG_CMD_UBIFS
+#define BOOT_TARGET_UBIFS(func) func(UBIFS, ubifs, 0)
+#else
+#define BOOT_TARGET_UBIFS(func)
+#endif
+
+#define BOOT_TARGET_DEVICES(func) \
+ BOOT_TARGET_MMC1(func) \
+ BOOT_TARGET_UBIFS(func) \
+ BOOT_TARGET_MMC0(func) \
+ BOOT_TARGET_MMC2(func) \
+ BOOT_TARGET_PXE(func)
/*
* bootcmd for stm32mp1:
* for serial/usb: execute the stm32prog command
* for mmc boot (eMMC, SD card), boot only on the same device
- * for nand boot, boot with on ubifs partition on nand
+ * for nand or spi-nand boot, boot with on ubifs partition on UBI partition
* for nor boot, use the default order
*/
#define STM32MP_BOOTCMD "bootcmd_stm32mp=" \
"if test ${boot_device} = serial || test ${boot_device} = usb;" \
"then stm32prog ${boot_device} ${boot_instance}; " \
"else " \
+ "run env_check;" \
"if test ${boot_device} = mmc;" \
"then env set boot_targets \"mmc${boot_instance}\"; fi;" \
- "if test ${boot_device} = nand;" \
+ "if test ${boot_device} = nand ||" \
+ " test ${boot_device} = spi-nand ;" \
"then env set boot_targets ubifs0; fi;" \
"run distro_bootcmd;" \
"fi;\0"
#include <config_distro_bootcmd.h>
-#if defined(CONFIG_STM32_QSPI) || defined(CONFIG_NAND_STM32_FMC)
-#define CONFIG_SYS_MTDPARTS_RUNTIME
-#endif
-
-#define STM32MP_MTDPARTS \
- "mtdparts_nor0=256k(fsbl1),256k(fsbl2),2m(ssbl),256k(u-boot-env),-(nor_user)\0" \
- "mtdparts_nand0=2m(fsbl),2m(ssbl1),2m(ssbl2),-(UBI)\0"
-
/*
* memory layout for 32M uncompressed/compressed kernel,
* 1M fdt, 1M script, 1M pxe and 1M for splashimage
* and the ramdisk at the end.
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "bootdelay=1\0" \
"kernel_addr_r=0xc2000000\0" \
"fdt_addr_r=0xc4000000\0" \
"scriptaddr=0xc4100000\0" \
"pxefile_addr_r=0xc4200000\0" \
"splashimage=0xc4300000\0" \
"ramdisk_addr_r=0xc4400000\0" \
- "fdt_high=0xffffffff\0" \
- "initrd_high=0xffffffff\0" \
+ "altbootcmd=run bootcmd\0" \
+ "env_default=1\0" \
+ "env_check=if test $env_default -eq 1;"\
+ " then env set env_default 0;env save;fi\0" \
STM32MP_BOOTCMD \
- STM32MP_MTDPARTS \
- BOOTENV
+ BOOTENV \
+ "boot_net_usb_start=true\0"
#endif /* ifndef CONFIG_SPL_BUILD */
#endif /* ifdef CONFIG_DISTRO_DEFAULTS*/
projects / J-u-boot.git / blobdiff