Convert all of CONFIG_CONS_INDEX to Kconfig

[J-u-boot.git] / include / configs / ulcb.h

diff --git a/include/configs/ulcb.h b/include/configs/ulcb.h
index b54e63c2a2fbc3fdf880b219a6419351dd2c3356..dfd6436b3caf528c717adde4e00840fd01d69fa2 100644 (file)
--- a/include/configs/ulcb.h
+++ b/include/configs/ulcb.h
@@ -12,96 +12,22 @@
 
 #undef DEBUG
 
-#define CONFIG_RCAR_BOARD_STRING "ULCB"
-
 #include "rcar-gen3-common.h"
 
-/* M3 ULCB has 2 banks, each with 1 GiB of RAM */
-#if defined(CONFIG_R8A7796)
-#undef PHYS_SDRAM_1_SIZE
-#undef PHYS_SDRAM_2_SIZE
-#define PHYS_SDRAM_1_SIZE              (0x40000000u - DRAM_RSV_SIZE)
-#define PHYS_SDRAM_2_SIZE              0x40000000u
-#endif
-
-/* SCIF */
-#define CONFIG_CONS_SCIF2
-#define CONFIG_CONS_INDEX      2
-#define CONFIG_SH_SCIF_CLK_FREQ        CONFIG_S3D4_CLK_FREQ
-
-/* [A] Hyper Flash */
-/* use to RPC(SPI Multi I/O Bus Controller) */
-
 /* Ethernet RAVB */
-#define CONFIG_PHY_MICREL
 #define CONFIG_BITBANGMII
 #define CONFIG_BITBANGMII_MULTI
 
 /* Board Clock */
 /* XTAL_CLK : 33.33MHz */
-#define RCAR_XTAL_CLK          33333333u
-#define CONFIG_SYS_CLK_FREQ    RCAR_XTAL_CLK
-/* ch0to2 CPclk, ch3to11 S3D2_PEREclk, ch12to14 S3D2_RTclk */
-/* CPclk 16.66MHz, S3D2 133.33MHz , S3D4 66.66MHz          */
-#define CONFIG_CP_CLK_FREQ     (CONFIG_SYS_CLK_FREQ / 2)
-#define CONFIG_PLL1_CLK_FREQ   (CONFIG_SYS_CLK_FREQ * 192 / 2)
-#define CONFIG_S3D2_CLK_FREQ   (266666666u/2)
-#define CONFIG_S3D4_CLK_FREQ   (266666666u/4)
+#define CONFIG_SYS_CLK_FREQ    33333333u
 
 /* Generic Timer Definitions (use in assembler source) */
 #define COUNTER_FREQUENCY      0xFE502A        /* 16.66MHz from CPclk */
 
-/* Generic Interrupt Controller Definitions */
-#define CONFIG_GICV2
-#define GICD_BASE      0xF1010000
-#define GICC_BASE      0xF1020000
-
-/* CPLD SPI */
-#define CONFIG_CMD_SPI
-#define CONFIG_SOFT_SPI
-#define SPI_DELAY      udelay(0)
-#define SPI_SDA(val)   ulcb_softspi_sda(val)
-#define SPI_SCL(val)   ulcb_softspi_scl(val)
-#define SPI_READ       ulcb_softspi_read()
-#ifndef        __ASSEMBLY__
-void ulcb_softspi_sda(int);
-void ulcb_softspi_scl(int);
-unsigned char ulcb_softspi_read(void);
-#endif
-
-/* i2c */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SH
-#define CONFIG_SYS_I2C_SLAVE           0x60
-#define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS      1
-#define CONFIG_SYS_I2C_SH_SPEED0       400000
-#define CONFIG_SH_I2C_DATA_HIGH                4
-#define CONFIG_SH_I2C_DATA_LOW         5
-#define CONFIG_SH_I2C_CLOCK            10000000
-
-#define CONFIG_SYS_I2C_POWERIC_ADDR    0x30
-
-/* USB */
-#ifdef CONFIG_R8A7795
-#define CONFIG_USB_MAX_CONTROLLER_COUNT        3
-#else
-#define CONFIG_USB_MAX_CONTROLLER_COUNT        2
-#endif
-
-/* SDHI */
-#define CONFIG_SH_SDHI_FREQ            200000000
-
 /* Environment in eMMC, at the end of 2nd "boot sector" */
 #define CONFIG_ENV_OFFSET              (-CONFIG_ENV_SIZE)
 #define CONFIG_SYS_MMC_ENV_DEV         1
 #define CONFIG_SYS_MMC_ENV_PART                2
 
-/* Module stop status bits */
-/* MFIS, SCIF1 */
-#define CONFIG_SMSTP2_ENA      0x00002040
-/* SCIF2 */
-#define CONFIG_SMSTP3_ENA      0x00000400
-/* INTC-AP, IRQC */
-#define CONFIG_SMSTP4_ENA      0x00000180
-
 #endif /* __ULCB_H */