#define STATUS_LED_BLINKING 1
#define STATUS_LED_ON 2
+void status_led_init(void);
void status_led_tick (unsigned long timestamp);
void status_led_set (int led, int state);
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-/***** GEN860T *********************************************************/
-#elif defined(CONFIG_GEN860T)
-
-# define STATUS_LED_PAR im_ioport.iop_papar
-# define STATUS_LED_DIR im_ioport.iop_padir
-# define STATUS_LED_ODR im_ioport.iop_paodr
-# define STATUS_LED_DAT im_ioport.iop_padat
-
-# define STATUS_LED_BIT 0x0800 /* Red LED 0 is on PA.4 */
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
-# define STATUS_LED_STATE STATUS_LED_OFF
-# define STATUS_LED_BIT1 0x0400 /* Grn LED 1 is on PA.5 */
-# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 8)
-# define STATUS_LED_STATE1 STATUS_LED_BLINKING
-# define STATUS_LED_BIT2 0x0080 /* Red LED 2 is on PA.8 */
-# define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 4)
-# define STATUS_LED_STATE2 STATUS_LED_OFF
-# define STATUS_LED_BIT3 0x0040 /* Grn LED 3 is on PA.9 */
-# define STATUS_LED_PERIOD3 (CONFIG_SYS_HZ / 4)
-# define STATUS_LED_STATE3 STATUS_LED_OFF
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-# define STATUS_LED_BOOT 1 /* Boot status on LED 1 */
-
-/***** IVMS8 **********************************************************/
-#elif defined(CONFIG_IVMS8)
-
-# define STATUS_LED_PAR im_cpm.cp_pbpar
-# define STATUS_LED_DIR im_cpm.cp_pbdir
-# define STATUS_LED_ODR im_cpm.cp_pbodr
-# define STATUS_LED_DAT im_cpm.cp_pbdat
-
-# define STATUS_LED_BIT 0x00000010 /* LED 0 is on PB.27 */
-# define STATUS_LED_PERIOD (1 * CONFIG_SYS_HZ)
-# define STATUS_LED_STATE STATUS_LED_OFF
-# define STATUS_LED_BIT1 0x00000020 /* LED 1 is on PB.26 */
-# define STATUS_LED_PERIOD1 (1 * CONFIG_SYS_HZ)
-# define STATUS_LED_STATE1 STATUS_LED_OFF
-/* IDE LED usable for other purposes, too */
-# define STATUS_LED_BIT2 0x00000008 /* LED 2 is on PB.28 */
-# define STATUS_LED_PERIOD2 (1 * CONFIG_SYS_HZ)
-# define STATUS_LED_STATE2 STATUS_LED_OFF
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-
-# define STATUS_ILOCK_SWITCH 0x00800000 /* ILOCK switch in IRQ4 */
-
-# define STATUS_ILOCK_PERIOD (CONFIG_SYS_HZ / 10) /* about every 100 ms */
-
-# define STATUS_LED_YELLOW 0
-# define STATUS_LED_GREEN 1
-# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */
-
-/***** IVML24 *********************************************************/
-#elif defined(CONFIG_IVML24)
-
-# define STATUS_LED_PAR im_cpm.cp_pbpar
-# define STATUS_LED_DIR im_cpm.cp_pbdir
-# define STATUS_LED_ODR im_cpm.cp_pbodr
-# define STATUS_LED_DAT im_cpm.cp_pbdat
-
-# define STATUS_LED_BIT 0x00000010 /* LED 0 is on PB.27 */
-# define STATUS_LED_PERIOD (1 * CONFIG_SYS_HZ)
-# define STATUS_LED_STATE STATUS_LED_OFF
-# define STATUS_LED_BIT1 0x00000020 /* LED 1 is on PB.26 */
-# define STATUS_LED_PERIOD1 (1 * CONFIG_SYS_HZ)
-# define STATUS_LED_STATE1 STATUS_LED_OFF
-/* IDE LED usable for other purposes, too */
-# define STATUS_LED_BIT2 0x00000008 /* LED 2 is on PB.28 */
-# define STATUS_LED_PERIOD2 (1 * CONFIG_SYS_HZ)
-# define STATUS_LED_STATE2 STATUS_LED_OFF
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-
-# define STATUS_ILOCK_SWITCH 0x00004000 /* ILOCK is on PB.17 */
-
-# define STATUS_ILOCK_PERIOD (CONFIG_SYS_HZ / 10) /* about every 100 ms */
-
-# define STATUS_LED_YELLOW 0
-# define STATUS_LED_GREEN 1
-# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */
-
-/***** ICU862 ********************************************************/
-#elif defined(CONFIG_ICU862)
-
-# define STATUS_LED_PAR im_ioport.iop_papar
-# define STATUS_LED_DIR im_ioport.iop_padir
-# define STATUS_LED_ODR im_ioport.iop_paodr
-# define STATUS_LED_DAT im_ioport.iop_padat
-
-# define STATUS_LED_BIT 0x4000 /* LED 0 is on PA.1 */
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-# define STATUS_LED_BIT1 0x1000 /* LED 1 is on PA.3 */
-# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ)
-# define STATUS_LED_STATE1 STATUS_LED_OFF
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
/***** Someone else defines these *************************************/
#elif defined(STATUS_LED_PAR)
* filling this file up with lots of custom board stuff.
*/
-/***** NetVia ********************************************************/
-#elif defined(CONFIG_NETVIA)
-
-#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1
-
-#define STATUS_LED_PAR im_ioport.iop_pdpar
-#define STATUS_LED_DIR im_ioport.iop_pddir
-#undef STATUS_LED_ODR
-#define STATUS_LED_DAT im_ioport.iop_pddat
-
-# define STATUS_LED_BIT 0x0080 /* PD.8 */
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-
-# define STATUS_LED_BIT1 0x0040 /* PD.9 */
-# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE1 STATUS_LED_OFF
-
-# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
-#endif
-
-/***** CMI ********************************************************/
-#elif defined(CONFIG_CMI)
-# define STATUS_LED_DIR im_mios.mios_mpiosm32ddr
-# define STATUS_LED_DAT im_mios.mios_mpiosm32dr
-
-# define STATUS_LED_BIT 0x2000 /* Select one of the 16 possible*/
- /* MIOS outputs */
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) /* Blinking periode is 500 ms */
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 0 */
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
-/***** KUP4K, KUP4X ****************************************************/
-#elif defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
-
-# define STATUS_LED_PAR im_ioport.iop_papar
-# define STATUS_LED_DIR im_ioport.iop_padir
-# define STATUS_LED_ODR im_ioport.iop_paodr
-# define STATUS_LED_DAT im_ioport.iop_padat
-
-# define STATUS_LED_BIT 0x00000300 /* green + red PA[8]=yellow, PA[7]=red, PA[6]=green */
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
-#elif defined(CONFIG_SVM_SC8xx)
-# define STATUS_LED_PAR im_cpm.cp_pbpar
-# define STATUS_LED_DIR im_cpm.cp_pbdir
-# define STATUS_LED_ODR im_cpm.cp_pbodr
-# define STATUS_LED_DAT im_cpm.cp_pbdat
-
-# define STATUS_LED_BIT 0x00000001
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
-/***** STx XTc ********************************************************/
-#elif defined(CONFIG_STXXTC)
-/* XXX empty just to avoid the error */
-/************************************************************************/
#elif defined(CONFIG_V38B)
# define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */
extern void __led_toggle (led_id_t mask);
extern void __led_init (led_id_t mask, int state);
extern void __led_set (led_id_t mask, int state);
+void __led_blink(led_id_t mask, int freq);
#else
# error Status LED configuration missing
#endif
projects / J-u-boot.git / blobdiff