configs: Migrate CMD_NAND*

[J-u-boot.git] / include / configs / pcm052.h

diff --git a/include/configs/pcm052.h b/include/configs/pcm052.h
index eb1944aa290983c428a4a03e1bc2db1b2eeb15e6..71c5078cc797744115e2aa427d6c183d71170d22 100644 (file)
--- a/include/configs/pcm052.h
+++ b/include/configs/pcm052.h
@@ -11,10 +11,6 @@
 
 #include <asm/arch/imx-regs.h>
 
-#define CONFIG_VF610
-
-#define CONFIG_SYS_THUMB_BUILD
-
 #define CONFIG_SKIP_LOWLEVEL_INIT
 
 /* Enable passing of ATAGs */
@@ -23,31 +19,19 @@
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN          (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
 
-#define CONFIG_BOARD_EARLY_INIT_F
-
 /* Allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_BAUDRATE                        115200
 
 /* NAND support */
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NAND_TRIMFFS
 #define CONFIG_SYS_NAND_ONFI_DETECTION
 
 #ifdef CONFIG_CMD_NAND
-#define CONFIG_USE_ARCH_MEMCPY
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define CONFIG_SYS_NAND_BASE           NFC_BASE_ADDR
 
 #define CONFIG_JFFS2_NAND
 
-/* UBI */
-#define CONFIG_CMD_UBIFS
-#define CONFIG_RBTREE
-#define CONFIG_LZO
-
 /* Dynamic MTD partition support */
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_MTD_PARTITIONS
 #define CONFIG_MTD_DEVICE
 
@@ -66,18 +50,11 @@
 
 #endif
 
-#define CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
 #define CONFIG_SYS_FSL_ESDHC_NUM       1
 
 /*#define CONFIG_ESDHC_DETECT_USE_EXTERN_IRQ1*/
-#define CONFIG_SYS_FSL_ERRATUM_ESDHC135
-#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
-#define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001
-
-#define CONFIG_GENERIC_MMC
-#define CONFIG_DOS_PARTITION
 
 #define CONFIG_FEC_MXC
 #define CONFIG_MII
@@ -101,13 +78,11 @@
 #define CONFIG_SYS_I2C_MXC
 
 /* RTC (actually an RV-4162 but M41T62-compatible) */
-#define CONFIG_CMD_DATE
 #define CONFIG_RTC_M41T62
 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
 #define CONFIG_SYS_RTC_BUS_NUM 2
 
 /* EEPROM (24FC256) */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
 #define CONFIG_SYS_I2C_EEPROM_BUS 2
@@ -241,12 +216,6 @@
 
 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE               (128 * 1024)    /* regular stack */
-
 /* Physical memory map */
 #define CONFIG_NR_DRAM_BANKS           1
 #define PHYS_SDRAM                     (0x80000000)
@@ -261,9 +230,7 @@
 #define CONFIG_SYS_INIT_SP_ADDR \
        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 
-/* FLASH and environment organization */
-#define CONFIG_SYS_NO_FLASH
-
+/* environment organization */
 #ifdef CONFIG_ENV_IS_IN_MMC
 #define CONFIG_ENV_SIZE                        (8 * 1024)