Merge git://git.denx.de/u-boot-sunxi

[J-u-boot.git] / include / configs / MPC8572DS.h

diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
index e1345609782854c5f230b11cccf29b12c62179fa..1959fa5b01576378884fa87946ab3e38d628a065 100644 (file)
--- a/include/configs/MPC8572DS.h
+++ b/include/configs/MPC8572DS.h
@@ -26,11 +26,8 @@
 #endif
 
 /* High Level Configuration Options */
-#define CONFIG_BOOKE           1       /* BOOKE */
-#define CONFIG_E500            1       /* BOOKE e500 family */
 #define CONFIG_MP              1       /* support multiple processors */
 
-#define CONFIG_FSL_ELBC                1       /* Has Enhanced localbus controller */
 #define CONFIG_PCIE1           1       /* PCIE controller 1 (slot 1) */
 #define CONFIG_PCIE2           1       /* PCIE controller 2 (slot 2) */
 #define CONFIG_PCIE3           1       /* PCIE controller 3 (ULI bridge) */
@@ -39,8 +36,6 @@
 #define CONFIG_FSL_PCIE_RESET  1       /* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 
-#define CONFIG_FSL_LAW         1       /* Use common FSL init code */
-
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
@@ -86,7 +81,6 @@
 
 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
@@ -98,7 +92,6 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x00000000
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_NUM_DDR_CONTROLLERS     2
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 #define CONFIG_CHIP_SELECTS_PER_CTRL   2
 
@@ -292,7 +285,6 @@
                                CONFIG_SYS_NAND_BASE + 0x80000,\
                                CONFIG_SYS_NAND_BASE + 0xC0000}
 #define CONFIG_SYS_MAX_NAND_DEVICE    4
-#define CONFIG_CMD_NAND                1
 #define CONFIG_NAND_FSL_ELBC   1
 #define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
 #define CONFIG_SYS_NAND_MAX_OOBFREE    5
@@ -477,7 +469,6 @@
 #endif
 
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #define CONFIG_SCSI_AHCI
 
 #ifdef CONFIG_SCSI_AHCI
@@ -528,8 +519,6 @@
 #define TSEC4_PHYIDX           0
 
 #define CONFIG_ETHPRIME                "eTSEC1"
-
-#define CONFIG_PHY_GIGE                1       /* Include GbE speed/duplex detection */
 #endif /* CONFIG_TSEC_ENET */
 
 /*
@@ -539,7 +528,6 @@
 #if defined(CONFIG_SYS_RAMBOOT)
 
 #else
-       #define CONFIG_ENV_IS_IN_FLASH  1
        #if CONFIG_SYS_MONITOR_BASE > 0xfff80000
        #define CONFIG_ENV_ADDR 0xfff80000
        #else
@@ -552,28 +540,14 @@
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
 
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#define CONFIG_SCSI
-#endif
-
 /*
  * USB
  */
-#define CONFIG_USB_EHCI
 
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_USB_EHCI_PCI
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_PCI_EHCI_DEVICE                 0
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS     2
 #endif
 
 #undef CONFIG_WATCHDOG                 /* watchdog disabled */
@@ -630,10 +604,6 @@
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR                1000000
 
-#undef  CONFIG_BOOTARGS                /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE        115200
-
 #define        CONFIG_EXTRA_ENV_SETTINGS                               \
 "hwconfig=fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1,ecc=off\0"                \
 "netdev=eth0\0"                                                \