phy: marvell: a3700: Fix configuring polarity invert bits

[J-u-boot.git] / README

diff --git a/README b/README
index 495c1ae3549e208a5166090e76187af1b2729fde..840b192aae509854dda357441ff341f4889d853f 100644 (file)
--- a/README
+++ b/README
@@ -300,7 +300,6 @@ board_init_r():
        - loads U-Boot or (in falcon mode) Linux
 
 
-
 Configuration Options:
 ----------------------
 
@@ -465,10 +464,6 @@ The following options need to be configured:
                Board config to use DDR3L. It can be enabled for SoCs with
                DDR3L controllers.
 
-               CONFIG_SYS_FSL_DDR4
-               Board config to use DDR4. It can be enabled for SoCs with
-               DDR4 controllers.
-
                CONFIG_SYS_FSL_IFC_BE
                Defines the IFC controller register space as Big Endian
 
@@ -481,15 +476,6 @@ The following options need to be configured:
                CONFIG_SYS_FSL_LBC_CLK_DIV
                Defines divider of platform clock(clock input to eLBC controller).
 
-               CONFIG_SYS_FSL_PBL_PBI
-               It enables addition of RCW (Power on reset configuration) in built image.
-               Please refer doc/README.pblimage for more details
-
-               CONFIG_SYS_FSL_PBL_RCW
-               It adds PBI(pre-boot instructions) commands in u-boot build image.
-               PBI commands can be used to configure SoC before it starts the execution.
-               Please refer doc/README.pblimage for more details
-
                CONFIG_SYS_FSL_DDR_BE
                Defines the DDR controller register space as Big Endian
 
@@ -599,16 +585,6 @@ The following options need to be configured:
                crash. This is needed for buggy hardware (uc101) where
                no pull down resistor is connected to the signal IDE5V_DD7.
 
-               CONFIG_MACH_TYPE        [relevant for ARM only][mandatory]
-
-               This setting is mandatory for all boards that have only one
-               machine type and must be used to specify the machine type
-               number as it appears in the ARM machine registry
-               (see https://www.arm.linux.org.uk/developer/machines/).
-               Only boards that have multiple machine types supported
-               in a single configuration file and the machine type is
-               runtime discoverable, do not have to use this setting.
-
 - vxWorks boot parameters:
 
                bootvx constructs a valid bootline using the following
@@ -671,11 +647,6 @@ The following options need to be configured:
                time on others. This setting #define's the initial
                value of the "loads_echo" environment variable.
 
-- Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
-               CONFIG_KGDB_BAUDRATE
-               Select one of the baudrates listed in
-               CONFIG_SYS_BAUDRATE_TABLE, see below.
-
 - Removal of commands
                If no commands are needed to boot, you can disable
                CONFIG_CMDLINE to remove them. In this case, the command line
@@ -879,17 +850,6 @@ The following options need to be configured:
                Support for National dp8382[01] gigabit chips.
 
 - NETWORK Support (other):
-
-               CONFIG_DRIVER_AT91EMAC
-               Support for AT91RM9200 EMAC.
-
-                       CONFIG_RMII
-                       Define this to use reduced MII inteface
-
-                       CONFIG_DRIVER_AT91EMAC_QUIET
-                       If this defined, the driver is quiet.
-                       The driver doen't show link status messages.
-
                CONFIG_CALXEDA_XGMAC
                Support for the Calxeda XGMAC device
 
@@ -2114,9 +2074,6 @@ The following options need to be configured:
                Defines the size and behavior of the NAND that SPL uses
                to read U-Boot
 
-               CONFIG_SYS_NAND_U_BOOT_OFFS
-               Location in NAND to read U-Boot from
-
                CONFIG_SYS_NAND_U_BOOT_DST
                Location in memory to load U-Boot to
 
@@ -2654,9 +2611,6 @@ Low Level (hardware related) configuration options:
   CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
                Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
 
-- CONFIG_PCI_INDIRECT_BRIDGE:
-               Enable support for indirect PCI bridges.
-
 - CONFIG_SYS_SRIO:
                Chip has SRIO or not
 
@@ -2754,22 +2708,6 @@ Low Level (hardware related) configuration options:
                This only takes effect if the memory commands are activated
                globally (CONFIG_CMD_MEMORY).
 
-- CONFIG_SKIP_LOWLEVEL_INIT
-               [ARM, NDS32, MIPS, RISC-V only] If this variable is defined, then certain
-               low level initializations (like setting up the memory
-               controller) are omitted and/or U-Boot does not
-               relocate itself into RAM.
-
-               Normally this variable MUST NOT be defined. The only
-               exception is when U-Boot is loaded (to RAM) by some
-               other boot loader or by a debugger which performs
-               these initializations itself.
-
-- CONFIG_SKIP_LOWLEVEL_INIT_ONLY
-               [ARM926EJ-S only] This allows just the call to lowlevel_init()
-               to be skipped. The normal CP15 init (such as enabling the
-               instruction cache) is still performed.
-
 - CONFIG_SPL_BUILD
                Set when the currently-running compilation is for an artifact
                that will end up in the SPL (as opposed to the TPL or U-Boot