Convert CONFIG_CHIP_SELECTS_PER_CTRL to Kconfig

[J-u-boot.git] / include / configs / ls1088a_common.h

diff --git a/include/configs/ls1088a_common.h b/include/configs/ls1088a_common.h
index f39f0316c599140e2fcea1a05f36afdefb46fef1..965fdfead24b8ec715df586d7774eb8ba095d108 100644 (file)
--- a/include/configs/ls1088a_common.h
+++ b/include/configs/ls1088a_common.h
@@ -20,8 +20,6 @@
 #undef CONFIG_DISPLAY_CPUINFO
 #endif
 
-#define CONFIG_REMAKE_ELF
-
 #include <asm/arch/stream_id_lsch3.h>
 #include <asm/arch/config.h>
 #include <asm/arch/soc.h>
@@ -49,11 +47,6 @@
 #define CPU_RELEASE_ADDR               secondary_boot_addr
 
 /* GPIO */
-#ifdef CONFIG_DM_GPIO
-#ifndef CONFIG_MPC8XXX_GPIO
-#define CONFIG_MPC8XXX_GPIO
-#endif
-#endif
 
 /* I2C */
 
@@ -63,13 +56,6 @@
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0) / 2)
 
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
-
-#if !defined(SPL_NO_IFC) || defined(CONFIG_TARGET_LS1088AQDS)
-/* IFC */
-#define CONFIG_FSL_IFC
-#endif
-
 /*
  * During booting, IFC is mapped at the region of 0x30000000.
  * But this region is limited to 256MB. To accommodate NOR, promjet
@@ -142,17 +128,10 @@ unsigned long long get_qixis_addr(void);
 
 /* SATA */
 #ifdef CONFIG_SCSI
-#define CONFIG_SCSI_AHCI_PLAT
 #define CONFIG_SYS_SATA1               AHCI_BASE_ADDR1
-
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID    1
-#define CONFIG_SYS_SCSI_MAX_LUN                1
-#define CONFIG_SYS_SCSI_MAX_DEVICE     (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
-                                       CONFIG_SYS_SCSI_MAX_LUN)
 #endif
 
 /* Physical Memory Map */
-#define CONFIG_CHIP_SELECTS_PER_CTRL   4
 
 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE           128
@@ -175,25 +154,6 @@ unsigned long long get_qixis_addr(void);
        "console=ttyAMA0,38400n8\0"             \
        "mcinitcmd=fsl_mc start mc 0x580a00000" \
        " 0x580e00000 \0"
-
-#ifndef CONFIG_TFABOOT
-#if defined(CONFIG_QSPI_BOOT)
-#define CONFIG_BOOTCOMMAND     "sf probe 0:0;" \
-                               "sf read 0x80001000 0xd00000 0x100000;"\
-                               " fsl_mc lazyapply dpl 0x80001000 &&" \
-                               " sf read $kernel_load $kernel_start" \
-                               " $kernel_size && bootm $kernel_load"
-#elif defined(CONFIG_SD_BOOT)
-#define CONFIG_BOOTCOMMAND     "mmcinfo;mmc read 0x80001000 0x6800 0x800;"\
-                               " fsl_mc lazyapply dpl 0x80001000 &&" \
-                               " mmc read $kernel_load $kernel_start" \
-                               " $kernel_size && bootm $kernel_load"
-#else /* NOR BOOT*/
-#define CONFIG_BOOTCOMMAND     "fsl_mc lazyapply dpl 0x580d00000 &&" \
-                               " cp.b $kernel_start $kernel_load" \
-                               " $kernel_size && bootm $kernel_load"
-#endif
-#endif /* CONFIG_TFABOOT  */
 #endif
 
 /* Monitor Command Prompt */
@@ -206,7 +166,6 @@ unsigned long long get_qixis_addr(void);
 #ifdef CONFIG_SPL
 #define CONFIG_SPL_BSS_START_ADDR      0x80100000
 #define CONFIG_SPL_BSS_MAX_SIZE                0x00100000
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
 #define CONFIG_SPL_MAX_SIZE            0x16000
 #define CONFIG_SPL_STACK               (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
 #define CONFIG_SPL_TARGET              "u-boot-with-spl.bin"