Convert CONFIG_SYS_MALLOC_LEN to Kconfig

[J-u-boot.git] / include / configs / mx6sxsabreauto.h

diff --git a/include/configs/mx6sxsabreauto.h b/include/configs/mx6sxsabreauto.h
index 274cb3600219344460a2042cc1dcb2b33fc6527c..62b8de3c1aa4246d2c24474b97e65dff7494657d 100644 (file)
--- a/include/configs/mx6sxsabreauto.h
+++ b/include/configs/mx6sxsabreauto.h
@@ -1,9 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
  *
  * Configuration settings for the Freescale i.MX6SX Sabreauto board.
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -11,13 +10,6 @@
 
 #include "mx6_common.h"
 
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN          (3 * SZ_1M)
-
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_LATE_INIT
-
-#define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE           UART1_BASE
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
@@ -95,13 +87,8 @@
           "else run netboot; fi"
 
 /* Miscellaneous configurable options */
-#define CONFIG_SYS_MEMTEST_START       0x80000000
-#define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_MEMTEST_START + 0x10000)
-
-#define CONFIG_STACKSIZE               SZ_128K
 
 /* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS           1
 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 
 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
@@ -116,40 +103,17 @@
 /* MMC Configuration */
 #define CONFIG_SYS_FSL_ESDHC_ADDR      USDHC3_BASE_ADDR
 
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1                /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2                /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3                /* enable I2C bus 3 */
-#define CONFIG_SYS_I2C_SPEED             100000
-
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_PFUZE100
-#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
-
-/* NAND flash command */
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NAND_TRIMFFS
-
 /* NAND stuff */
-#define CONFIG_NAND_MXS
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define CONFIG_SYS_NAND_BASE           0x40000000
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_ONFI_DETECTION
 
 /* DMA stuff, needed for GPMI/MXS NAND support */
-#define CONFIG_APBH_DMA
-#define CONFIG_APBH_DMA_BURST
-#define CONFIG_APBH_DMA_BURST8
 
 /* Network */
 
 #define CONFIG_FEC_MXC
-#define CONFIG_MII
 
 #define IMX_FEC_BASE                   ENET2_BASE_ADDR
 #define CONFIG_FEC_MXC_PHYADDR          0x0
@@ -157,43 +121,13 @@
 #define CONFIG_FEC_XCV_TYPE             RGMII
 #define CONFIG_ETHPRIME                 "FEC"
 
-#define CONFIG_PHYLIB
-#define CONFIG_PHY_ATHEROS
-
 #ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_MXC_USB_FLAGS   0
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 #endif
 
-#define CONFIG_IMX_THERMAL
-
-#define CONFIG_FSL_QSPI
-#ifdef CONFIG_FSL_QSPI
-#define CONFIG_SYS_FSL_QSPI_AHB
-#define CONFIG_SF_DEFAULT_BUS          0
-#define CONFIG_SF_DEFAULT_CS           0
-#define CONFIG_SF_DEFAULT_SPEED        40000000
-#define CONFIG_SF_DEFAULT_MODE         SPI_MODE_0
-#define FSL_QSPI_FLASH_SIZE            SZ_32M
-#define FSL_QSPI_FLASH_NUM             2
-#endif
-
-#define CONFIG_ENV_OFFSET              (8 * SZ_64K)
-#define CONFIG_ENV_SIZE                        SZ_8K
-#define CONFIG_ENV_IS_IN_MMC
-
 #define CONFIG_SYS_FSL_USDHC_NUM       2
-#if defined(CONFIG_ENV_IS_IN_MMC)
-#define CONFIG_SYS_MMC_ENV_DEV         0  /*USDHC3*/
-#endif
-
-#define CONFIG_PCA953X
-#define CONFIG_SYS_I2C_PCA953X_WIDTH   { {0x30, 8}, {0x32, 8}, {0x34, 8} }
 
 #endif                         /* __CONFIG_H */