during serial port initialization (default y). Set this to n on
boards which have no debug serial port whatsoever.
+config SERIAL_PRESENT
+ bool "Provide a serial driver"
+ depends on DM_SERIAL
+ default y
+ help
+ In very space-constrained devices even the full UART driver is too
+ large. In this case the debug UART can still be used in some cases.
+ This option enables the full UART in U-Boot, so if is it disabled,
+ the full UART driver will be omitted, thus saving space.
+
+config SPL_SERIAL_PRESENT
+ bool "Provide a serial driver in SPL"
+ depends on DM_SERIAL
+ default y
+ help
+ In very space-constrained devices even the full UART driver is too
+ large. In this case the debug UART can still be used in some cases.
+ This option enables the full UART in SPL, so if is it disabled,
+ the full UART driver will be omitted, thus saving space.
+
config DM_SERIAL
bool "Enable Driver Model for serial drivers"
depends on DM
choice
prompt "Select which UART will provide the debug UART"
depends on DEBUG_UART
+ default DEBUG_UART_NS16550
config DEBUG_UART_ALTERA_JTAGUART
bool "Altera JTAG UART"
will need to provide parameters to make this work. The driver will
be available until the real driver-model serial is running.
+config DEBUG_UART_UARTLITE
+ bool "Xilinx Uartlite"
+ help
+ Select this to enable a debug UART using the serial_uartlite driver.
+ You will need to provide parameters to make this work. The driver will
+ be available until the real driver-model serial is running.
+
config DEBUG_UART_ZYNQ
bool "Xilinx Zynq"
help
- Select this to enable a debug UART using the serial_s5p driver. You
+ Select this to enable a debug UART using the serial_zynq driver. You
will need to provide parameters to make this work. The driver will
be available until the real driver-model serial is running.
+config DEBUG_UART_APBUART
+ depends on LEON3
+ bool "Gaisler APBUART"
+ help
+ Select this to enable a debug UART using the serial_leon3 driver. You
+ will need to provide parameters to make this work. The driver will
+ be available until the real driver model serial is running.
+
+config DEBUG_UART_PL010
+ bool "pl010"
+ help
+ Select this to enable a debug UART using the pl01x driver with the
+ PL010 UART type. You will need to provide parameters to make this
+ work. The driver will be available until the real driver model
+ serial is running.
+
+config DEBUG_UART_PL011
+ bool "pl011"
+ help
+ Select this to enable a debug UART using the pl01x driver with the
+ PL011 UART type. You will need to provide parameters to make this
+ work. The driver will be available until the real driver model
+ serial is running.
+
+config DEBUG_UART_PIC32
+ bool "Microchip PIC32"
+ depends on PIC32_SERIAL
+ help
+ Select this to enable a debug UART using the serial_pic32 driver. You
+ will need to provide parameters to make this work. The driver will
+ be available until the real driver model serial is running.
+
endchoice
config DEBUG_UART_BASE
debug_uart_init()). This can be useful just as a check that
everything is working.
+config DEBUG_UART_SKIP_INIT
+ bool "Skip UART initialization"
+ help
+ Select this if the UART you want to use for debug output is already
+ initialized by the time U-Boot starts its execution.
+
config ALTERA_JTAG_UART
bool "Altera JTAG UART support"
depends on DM_SERIAL
Select this to enable an UART for Altera devices. Please find
details on the "Embedded Peripherals IP User Guide" of Altera.
-config ROCKCHIP_SERIAL
- bool "Rockchip on-chip UART support"
- depends on ARCH_ROCKCHIP && DM_SERIAL
+config FSL_LPUART
+ bool "Freescale LPUART support"
+ help
+ Select this to enable a Low Power UART for Freescale VF610 and
+ QorIQ Layerscape devices.
+
+config PIC32_SERIAL
+ bool "Support for Microchip PIC32 on-chip UART"
+ depends on DM_SERIAL && MACH_PIC32
+ default y
+ help
+ Support for the UART found on Microchip PIC32 SoC's.
+
+config SYS_NS16550
+ bool "NS16550 UART or compatible"
help
- Select this to enable a debug UART for Rockchip devices. This uses
- the ns16550 driver. You will need to #define CONFIG_SYS_NS16550 in
- your board config header. The clock input is automatically set to
- use the oscillator (24MHz).
+ Support NS16550 UART or compatible. This can be enabled in the
+ device tree with the correct input clock frequency. If the input
+ clock frequency is not defined in the device tree, the macro
+ CONFIG_SYS_NS16550_CLK defined in a legacy board header file will
+ be used. It can be a constant or a function to get clock, eg,
+ get_serial_clock().
config SANDBOX_SERIAL
bool "Sandbox UART support"
If you have a UniPhier based board and want to use the on-chip
serial ports, say Y to this option. If unsure, say N.
-config X86_SERIAL
- bool "Support for 16550 serial port on x86 machines"
- depends on X86
- default y
+config XILINX_UARTLITE
+ bool "Xilinx Uarlite support"
+ depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || 4xx)
help
- Most x86 machines have a ns16550 UART or compatible. This can be
- enabled in the device tree with the correct input clock frequency
- provided (default 1843200). Enable this to obtain serial console
- output.
+ If you have a Xilinx based board and want to use the uartlite
+ serial ports, say Y to this option. If unsure, say N.
endmenu
projects / J-u-boot.git / blobdiff