#define CONFIG_INITRD_TAG 1
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
-#define CFG_USE_MAIN_OSCILLATOR 1
+#define CONFIG_SYS_USE_MAIN_OSCILLATOR 1
/* flash */
-#define MC_PUIA_VAL 0x00000000
-#define MC_PUP_VAL 0x00000000
-#define MC_PUER_VAL 0x00000000
-#define MC_ASR_VAL 0x00000000
-#define MC_AASR_VAL 0x00000000
-#define EBI_CFGR_VAL 0x00000000
-#define SMC2_CSR_VAL 0x100032ad /* 16bit, 2 TDF, 4 WS */
+#define CONFIG_SYS_MC_PUIA_VAL 0x00000000
+#define CONFIG_SYS_MC_PUP_VAL 0x00000000
+#define CONFIG_SYS_MC_PUER_VAL 0x00000000
+#define CONFIG_SYS_MC_ASR_VAL 0x00000000
+#define CONFIG_SYS_MC_AASR_VAL 0x00000000
+#define CONFIG_SYS_EBI_CFGR_VAL 0x00000000
+#define CONFIG_SYS_SMC_CSR0_VAL 0x100032ad /* 16bit, 2 TDF, 4 WS */
/* clocks */
-#define PLLAR_VAL 0x2026BE04 /* 179,712 MHz for PCK */
-#define PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */
-#define MCKR_VAL 0x00000202 /* PCK/3 = MCK Master Clock = 69.120MHz from PLLA */
+#define CONFIG_SYS_PLLAR_VAL 0x2026BE04 /* 179,712 MHz for PCK */
+#define CONFIG_SYS_PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */
+#define CONFIG_SYS_MCKR_VAL 0x00000202 /* PCK/3 = MCK Master Clock = 69.120MHz from PLLA */
/* sdram */
-#define PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */
-#define PIOC_BSR_VAL 0x00000000
-#define PIOC_PDR_VAL 0xFFFF0000
-#define EBI_CSA_VAL 0x00000002 /* CS1=SDRAM */
-#define SDRC_CR_VAL 0x3399c1d4 /* set up the SDRAM */
-#define SDRAM 0x20000000 /* address of the SDRAM */
-#define SDRAM1 0x20000080 /* address of the SDRAM */
-#define SDRAM_VAL 0x00000000 /* value written to SDRAM */
-#define SDRC_MR_VAL 0x00000002 /* Precharge All */
-#define SDRC_MR_VAL1 0x00000004 /* refresh */
-#define SDRC_MR_VAL2 0x00000003 /* Load Mode Register */
-#define SDRC_MR_VAL3 0x00000000 /* Normal Mode */
-#define SDRC_TR_VAL 0x000002E0 /* Write refresh rate */
+#define CONFIG_SYS_PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */
+#define CONFIG_SYS_PIOC_BSR_VAL 0x00000000
+#define CONFIG_SYS_PIOC_PDR_VAL 0xFFFF0000
+#define CONFIG_SYS_EBI_CSA_VAL 0x00000002 /* CS1=CONFIG_SYS_SDRAM */
+#define CONFIG_SYS_SDRC_CR_VAL 0x3399c1d4 /* set up the CONFIG_SYS_SDRAM */
+#define CONFIG_SYS_SDRAM 0x20000000 /* address of the CONFIG_SYS_SDRAM */
+#define CONFIG_SYS_SDRAM1 0x20000080 /* address of the CONFIG_SYS_SDRAM */
+#define CONFIG_SYS_SDRAM_VAL 0x00000000 /* value written to CONFIG_SYS_SDRAM */
+#define CONFIG_SYS_SDRC_MR_VAL 0x00000002 /* Precharge All */
+#define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */
+#define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */
+#define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */
+#define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */
+#else
+#define CONFIG_SKIP_RELOCATE_UBOOT
#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CONFIG_BAUDRATE 9600
*/
/* define one of these to choose the DBGU, USART0 or USART1 as console */
+#define CONFIG_AT91RM9200_USART
#undef CONFIG_DBGU
#define CONFIG_USART0
#undef CONFIG_USART1
#define CONFIG_HARD_I2C
#ifdef CONFIG_HARD_I2C
-#define CFG_I2C_SPEED 0 /* not used */
-#define CFG_I2C_SLAVE 0 /* not used */
+#define CONFIG_SYS_I2C_SPEED 0 /* not used */
+#define CONFIG_SYS_I2C_SLAVE 0 /* not used */
#define CONFIG_RTC_RS5C372A /* RICOH I2C RTC */
-#define CFG_I2C_RTC_ADDR 0x32
-#define CFG_I2C_EEPROM_ADDR 0x50
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW
+#define CONFIG_SYS_I2C_RTC_ADDR 0x32
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
+#else
+#define CONFIG_TIMESTAMP
#endif
/* still about 20 kB free with this defined */
-#define CFG_LONGHELP
+#define CONFIG_SYS_LONGHELP
#define CONFIG_BOOTDELAY 1
-#ifdef CONFIG_HARD_I2C
-#define CONFIG_COMMANDS \
- ((CONFIG_CMD_DFL | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP ) & \
- ~(CFG_CMD_FPGA | CFG_CMD_MISC) )
-#else
-#define CONFIG_COMMANDS \
- ((CONFIG_CMD_DFL | \
- CFG_CMD_DHCP | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP ) & \
- ~(CFG_CMD_FPGA | CFG_CMD_MISC) )
-#define CONFIG_TIMESTAMP
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_MISC
+
+#if defined(CONFIG_HARD_I2C)
+ #define CONFIG_CMD_DATE
+ #define CONFIG_CMD_EEPROM
+ #define CONFIG_CMD_I2C
#endif
-#define CFG_LONGHELP
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+#define CONFIG_MISC_INIT_R
+#define CONFIG_SYS_LONGHELP
#define AT91_SMART_MEDIA_ALE (1 << 22) /* our ALE is AD22 */
#define AT91_SMART_MEDIA_CLE (1 << 21) /* our CLE is AD21 */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM 0x20000000
-#define PHYS_SDRAM_SIZE 0x1000000 /* 16 megs */
+#define PHYS_SDRAM_SIZE 0x1000000 /* 16 megs */
-#define CFG_MEMTEST_START PHYS_SDRAM
-#define CFG_MEMTEST_END CFG_MEMTEST_START + PHYS_SDRAM_SIZE - 262144
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_MEMTEST_START + PHYS_SDRAM_SIZE - 262144
#define CONFIG_DRIVER_ETHER
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_AT91C_USE_RMII
-#define CFG_SPI_WRITE_TOUT (5*CFG_HZ)
-#define CFG_MAX_DATAFLASH_BANKS 2
-#define CFG_MAX_DATAFLASH_PAGES 16384
-#define CFG_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* Logical adress for CS0 */
-#define CFG_DATAFLASH_LOGIC_ADDR_CS3 0xD0000000 /* Logical adress for CS3 */
+#define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ)
+#define CONFIG_SYS_MAX_DATAFLASH_BANKS 2
+#define CONFIG_SYS_MAX_DATAFLASH_PAGES 16384
+#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* Logical adress for CS0 */
+#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 0xD0000000 /* Logical adress for CS3 */
#define PHYS_FLASH_1 0x10000000
#define PHYS_FLASH_SIZE 0x800000 /* 8 megs main flash */
-#define CFG_FLASH_BASE PHYS_FLASH_1
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MAX_FLASH_BANKS 1
-#define CFG_MAX_FLASH_SECT 256
-#define CFG_FLASH_ERASE_TOUT (11 * CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT ( 2 * CFG_HZ) /* Timeout for Flash Write */
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x20000 /* after u-boot.bin */
-#define CFG_ENV_SECT_SIZE (64 << 10) /* sectors are 64 kB */
-#define CFG_ENV_SIZE (16 << 10) /* Use only 16 kB */
-
-#define CFG_LOAD_ADDR 0x21000000 /* default load address */
-
-#define CFG_BAUDRATE_TABLE { 115200, 57600, 38400, 19200, 9600 }
-
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_MAXARGS 32 /* max number of command args */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-
-#ifndef __ASSEMBLY__
-/*-----------------------------------------------------------------------
- * Board specific extension for bd_info
- *
- * This structure is embedded in the global bd_info (bd_t) structure
- * and can be used by the board specific code (eg board/...)
- */
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+#define CONFIG_SYS_FLASH_ERASE_TOUT (11 * CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT ( 2 * CONFIG_SYS_HZ) /* Timeout for Flash Write */
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_OFFSET 0x20000 /* after u-boot.bin */
+#define CONFIG_ENV_SECT_SIZE (64 << 10) /* sectors are 64 kB */
+#define CONFIG_ENV_SIZE (16 << 10) /* Use only 16 kB */
+
+#define CONFIG_SYS_LOAD_ADDR 0x21000000 /* default load address */
+
+#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 57600, 38400, 19200, 9600 }
+
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-struct bd_info_ext {
- /* helper variable for board environment handling
- *
- * env_crc_valid == 0 => uninitialised
- * env_crc_valid > 0 => environment crc in flash is valid
- * env_crc_valid < 0 => environment crc in flash is invalid
- */
- int env_crc_valid;
-};
-#endif /* __ASSEMBLY__ */
-
-#define CFG_HZ 1000
-#define CFG_HZ_CLOCK (AT91C_MASTER_CLOCK/2) /* AT91C_TC0_CMR is implicitly set to */
+#define CONFIG_SYS_HZ 1000
+#define CONFIG_SYS_HZ_CLOCK (AT91C_MASTER_CLOCK/2) /* AT91C_TC0_CMR is implicitly set to */
/* AT91C_TC_TIMER_DIV1_CLOCK */
#define CONFIG_STACKSIZE (32*1024) /* regular stack */
projects / J-u-boot.git / blobdiff