*----------------------------------------------------------------------*/
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
#define CONFIG_440 1 /* ... PPC440 family */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xFFF90000
#define CONFIG_4xx_DCACHE /* enable dcache */
#endif
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_F 1
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_BOARD_TYPES 1 /* support board types */
* Serial Port
*----------------------------------------------------------------------*/
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */
-#else
-#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
-#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
-#endif
/*-----------------------------------------------------------------------
* RTC
#endif
#ifdef CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_I2C_ENV_EEPROM_BUS 0
#define CONFIG_ENV_OFFSET 0 /* environment starts at the beginning of the EEPROM */
#define CONFIG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */
#endif
-/*
- * IPL (Initial Program Loader, integrated inside CPU)
- * Will load first 4k from NAND (SPL) into cache and execute it from there.
- *
- * SPL (Secondary Program Loader)
- * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
- * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
- * controller and the NAND controller so that the special U-Boot image can be
- * loaded from NAND to SDRAM.
- *
- * NUB (NAND U-Boot)
- * This NAND U-Boot (NUB) is a special U-Boot version which can be started
- * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
- *
- * On 440EPx the SPL is copied to SDRAM before the NAND controller is
- * set up. While still running from cache, I experienced problems accessing
- * the NAND controller. sr - 2006-08-25
- */
-#if defined (CONFIG_NAND_U_BOOT)
-#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
-#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
-#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */
-#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */
-#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
-
-/*
- * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
- */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
-
-/*
- * Now the NAND chip has to be defined (no autodetection used!)
- */
-#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */
-#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
-#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
-#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
-
-#define CONFIG_SYS_NAND_ECCSIZE 256
-#define CONFIG_SYS_NAND_ECCBYTES 3
-#define CONFIG_SYS_NAND_OOBSIZE 16
-#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_NAND
-/*
- * For NAND booting the environment is embedded in the U-Boot image. Please take
- * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
- */
-#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#endif
-
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
-#endif
#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
/* 440EPx errata CHIP 11 */
#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 400000
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
-
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
"cp.b 200000 fff90000 70000\0" \
""
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/* USB */
#define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_STORAGE
#define CONFIG_SYS_OHCI_BE_CONTROLLER
#define CONFIG_SYS_USB_OHCI_BOARD_INIT 1
#define USB_2_0_DEVICE
/* Partitions */
-#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_BSP
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
#define CONFIG_CMD_REGINFO
/* POST support */
#define CONFIG_LOGBUFFER
#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-
#define CONFIG_SUPPORT_VFAT
/*-----------------------------------------------------------------------
* Miscellaneous configurable options
*----------------------------------------------------------------------*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-#define CONFIG_AUTOBOOT_KEYED 1
-#define CONFIG_AUTOBOOT_PROMPT \
- "Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#undef CONFIG_AUTOBOOT_DELAY_STR
-#define CONFIG_AUTOBOOT_STOP_STR " "
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* General PCI */
-#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
/*
* On Sequoia CS0 and CS3 are switched when configuring for NAND booting
*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_NAND_CS 2 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
/* Memory Bank 2 (NAND-FLASH) initialization */
#define CONFIG_SYS_EBC_PB2AP 0x018003c0
#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
-#else
-#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */
-/* Memory Bank 2 (NOR-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB2AP 0x03017200
-#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FLASH_BASE | 0xda000)
-
-/* Memory Bank 0 (NAND-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x018003c0
-#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
-#endif
/* Memory Bank 1 (RESET) initialization */
#define CONFIG_SYS_EBC_PB1AP 0x7f817200 /* 0x03017200 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-#define CONFIG_SYS_NAND_QUIET_TEST 1
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#define CONFIG_API 1
#endif /* __CONFIG_H */
projects / J-u-boot.git / blobdiff