Convert CONFIG_CMD_DIAG to Kconfig

[J-u-boot.git] / include / configs / ls1043ardb.h

diff --git a/include/configs/ls1043ardb.h b/include/configs/ls1043ardb.h
index 307d947405ce673a8fe8b29748bfbf1019000066..5e570cd5e8d70ef23133d9efee09c7d808661b53 100644 (file)
--- a/include/configs/ls1043ardb.h
+++ b/include/configs/ls1043ardb.h
@@ -9,9 +9,6 @@
 
 #include "ls1043a_common.h"
 
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
 #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
 #define CONFIG_SYS_TEXT_BASE           0x82000000
 #else
@@ -27,12 +24,14 @@
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 /* Physical Memory Map */
 #define CONFIG_CHIP_SELECTS_PER_CTRL   4
-#define CONFIG_NR_DRAM_BANKS           1
+#define CONFIG_NR_DRAM_BANKS           2
 
 #define CONFIG_SYS_SPD_BUS_NUM         0
 
 #define CONFIG_FSL_DDR_BIST
+#ifndef CONFIG_SPL
 #define CONFIG_FSL_DDR_INTERACTIVE     /* Interactive debugging */
+#endif
 #define CONFIG_SYS_DDR_RAW_TIMING
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
@@ -91,7 +90,9 @@
 /*
  * NAND Flash Definitions
  */
+#ifndef SPL_NO_IFC
 #define CONFIG_NAND_FSL_IFC
+#endif
 
 #define CONFIG_SYS_NAND_BASE           0x7e800000
 #define CONFIG_SYS_NAND_BASE_PHYS      CONFIG_SYS_NAND_BASE
@@ -135,7 +136,7 @@
 #ifdef CONFIG_NAND_BOOT
 #define CONFIG_SPL_PAD_TO              0x20000         /* block aligned */
 #define CONFIG_SYS_NAND_U_BOOT_OFFS    CONFIG_SPL_PAD_TO
-#define CONFIG_SYS_NAND_U_BOOT_SIZE    (640 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_SIZE    (1024 << 10)
 #endif
 
 /*
@@ -214,6 +215,7 @@
 #define CONFIG_SYS_CS2_FTIM3           CONFIG_SYS_CPLD_FTIM3
 
 /* EEPROM */
+#ifndef SPL_NO_EEPROM
 #define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM              0
@@ -221,11 +223,14 @@
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5
+#endif
 
 /*
  * Environment
  */
+#ifndef SPL_NO_ENV
 #define CONFIG_ENV_OVERWRITE
+#endif
 
 #if defined(CONFIG_NAND_BOOT)
 #define CONFIG_ENV_IS_IN_NAND
@@ -244,9 +249,9 @@
 #endif
 
 /* FMan */
+#ifndef SPL_NO_FMAN
 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_FMAN_ENET
-#define CONFIG_CMD_MII
 #define CONFIG_PHYLIB
 #define CONFIG_PHYLIB_10G
 #define CONFIG_PHY_GIGE                /* Include GbE speed/duplex detection */
@@ -254,6 +259,7 @@
 #define CONFIG_PHY_VITESSE
 #define CONFIG_PHY_REALTEK
 #define CONFIG_PHY_AQUANTIA
+#define AQR105_IRQ_MASK                        0x40000000
 
 #define RGMII_PHY1_ADDR                        0x1
 #define RGMII_PHY2_ADDR                        0x2
@@ -267,5 +273,47 @@
 
 #define CONFIG_ETHPRIME                        "FM1@DTSEC3"
 #endif
+#endif
+
+/* QE */
+#ifndef SPL_NO_QE
+#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \
+       !defined(CONFIG_QSPI_BOOT)
+#define CONFIG_U_QE
+#endif
+#define CONFIG_SYS_QE_FW_ADDR     0x60600000
+#endif
+
+/* USB */
+#ifndef SPL_NO_USB
+#define CONFIG_HAS_FSL_XHCI_USB
+#ifdef CONFIG_HAS_FSL_XHCI_USB
+#define CONFIG_USB_XHCI_FSL
+#define CONFIG_USB_MAX_CONTROLLER_COUNT                3
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS     2
+#endif
+#endif
+
+/* SATA */
+#ifndef SPL_NO_SATA
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_CMD_SCSI
+#ifndef CONFIG_CMD_FAT
+#define CONFIG_CMD_FAT
+#endif
+#ifndef CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT2
+#endif
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID            2
+#define CONFIG_SYS_SCSI_MAX_LUN                        2
+#define CONFIG_SYS_SCSI_MAX_DEVICE             (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+                                               CONFIG_SYS_SCSI_MAX_LUN)
+#define SCSI_VEND_ID 0x1b4b
+#define SCSI_DEV_ID  0x9170
+#define CONFIG_SCSI_DEV_LIST {SCSI_VEND_ID, SCSI_DEV_ID}
+#endif
+
+#include <asm/fsl_secure_boot.h>
 
 #endif /* __LS1043ARDB_H__ */