Convert CONFIG_SYS_NAND_U_BOOT_LOCATIONS et al to Kconfig

[J-u-boot.git] / include / configs / siemens-am33x-common.h

diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h
index d146ba51dedb65c5ab72e0218a34e68aa1af7b40..fd74d5735e532a45ee1fe3d36fb4daf7bf1d437b 100644 (file)
--- a/include/configs/siemens-am33x-common.h
+++ b/include/configs/siemens-am33x-common.h
@@ -18,23 +18,12 @@
 #define CONFIG_DMA_COHERENT
 #define CONFIG_DMA_COHERENT_SIZE       (1 << 20)
 
-#define CONFIG_SYS_MALLOC_LEN          (16 * 1024 * 1024)
-#ifdef CONFIG_SIEMENS_MACH_TYPE
-#define CONFIG_MACH_TYPE               CONFIG_SIEMENS_MACH_TYPE
-#endif
-
-#define CONFIG_CMDLINE_TAG             /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
 /* commands to include */
 
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_ROOTPATH                "/opt/eldk"
 #endif
 
-#define CONFIG_ENV_OVERWRITE           1
-
 #define CONFIG_SYS_AUTOLOAD    "yes"
 
 /* Clock Defines */
@@ -55,8 +44,6 @@
  * start addr of ram disk
  */
 
-#define CONFIG_SYS_LOAD_ADDR           0x81000000 /* Default load address */
-
  /* Physical Memory Map */
 #define PHYS_DRAM_1                    0x80000000      /* DRAM Bank #1 */
 
@@ -68,18 +55,13 @@
 #define CONFIG_SYS_PTV                 2       /* Divisor: 2^(PTV+1) => 8 */
 
 /* NS16550 Configuration */
-#ifdef CONFIG_SPL_BUILD
 #define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE    (-4)
-#endif
 #define CONFIG_SYS_NS16550_CLK         (48000000)
 #define CONFIG_SYS_NS16550_COM1                0x44e09000
 #define CONFIG_SYS_NS16550_COM4                0x481a6000
 
 
 /* I2C Configuration */
-#define CONFIG_I2C
-#define CONFIG_SYS_I2C
 
 /* Defines for SPL */
 #define CONFIG_SPL_MAX_SIZE            (SRAM_SCRATCH_SPACE_ADDR - \
@@ -88,20 +70,8 @@
 #define CONFIG_SPL_BSS_START_ADDR      0x80000000
 #define CONFIG_SPL_BSS_MAX_SIZE                0x80000         /* 512 KB */
 
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME        "u-boot.img"
 
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT     (CONFIG_SYS_NAND_BLOCK_SIZE / \
-                                        CONFIG_SYS_NAND_PAGE_SIZE)
-#define CONFIG_SYS_NAND_PAGE_SIZE      2048
-#define CONFIG_SYS_NAND_OOBSIZE                64
-#define CONFIG_SYS_NAND_BLOCK_SIZE     (128*1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS  NAND_LARGE_BADBLOCK_POS
 #define CONFIG_SYS_NAND_ECCPOS         { 2, 3, 4, 5, 6, 7, 8, 9, \
                                         10, 11, 12, 13, 14, 15, 16, 17, \
                                         18, 19, 20, 21, 22, 23, 24, 25, \
@@ -120,8 +90,6 @@
 
 #define        CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 
-#define CONFIG_SYS_NAND_U_BOOT_OFFS    0x80000
-
 /*
  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
  * 64 bytes before this address should be set aside for u-boot.img's
@@ -135,9 +103,6 @@
  * Since SPL did pll and ddr initialization for us,
  * we don't need to do it twice.
  */
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#endif
 
 #ifndef CONFIG_SPL_BUILD
 /*
@@ -152,7 +117,6 @@
 #define CONFIG_USBD_HS
 
 /* USB Device Firmware Update support */
-#define CONFIG_SYS_DFU_DATA_BUF_SIZE   (1 << 20)
 #define DFU_MANIFEST_POLL_TIMEOUT      25000
 
 #endif /* CONFIG_SPL_BUILD */
@@ -170,8 +134,6 @@
  * 0x442000 - 0x800000 : Userland
  */
 
-#define CONFIG_BOOTP_DEFAULT
-#define CONFIG_BOOTP_SEND_HOSTNAME
 #define CONFIG_NET_RETRY_COUNT         10
 
 /* NAND support */