Kconfig: Finish migration of hashing commands

[J-u-boot.git] / include / configs / omapl138_lcdk.h

diff --git a/include/configs/omapl138_lcdk.h b/include/configs/omapl138_lcdk.h
index 43da339f397aa11eecf6571ff48cb14f0391ecd5..8904cd5cc772aa8bd5c0ae7fd1116fe2107bd49e 100644 (file)
--- a/include/configs/omapl138_lcdk.h
+++ b/include/configs/omapl138_lcdk.h
@@ -48,7 +48,6 @@
 #define CONFIG_SYS_MEMTEST_END         (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
 
 #define CONFIG_NR_DRAM_BANKS   1 /* we have 1 bank of DRAM */
-#define CONFIG_STACKSIZE       (256*1024) /* regular stack */
 
 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC (      \
        DAVINCI_SYSCFG_SUSPSRC_TIMER0 |         \
@@ -127,7 +126,6 @@
 #define CONFIG_SYS_NS16550_COM1        DAVINCI_UART2_BASE /* Base address of UART2 */
 #define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
 #define CONFIG_CONS_INDEX      1               /* use UART0 for console */
-#define CONFIG_BAUDRATE                115200          /* Default baud rate */
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
 
 #define CONFIG_SPI
@@ -158,7 +156,6 @@
 #ifdef CONFIG_USE_NAND
 #undef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NO_FLASH
 #define CONFIG_ENV_IS_IN_NAND          /* U-Boot env in NAND Flash  */
 #define CONFIG_ENV_OFFSET              0x0 /* Block 0--not used by bootcode */
 #define CONFIG_ENV_SIZE                        (128 << 9)
@@ -203,7 +200,6 @@
 
 #ifdef CONFIG_SYS_USE_NOR
 #define CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_SYS_NO_FLASH
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_PROTECTION
@@ -225,14 +221,12 @@
 #define CONFIG_ENV_SIZE                        (64 << 10)
 #define CONFIG_ENV_OFFSET              (256 << 10)
 #define CONFIG_ENV_SECT_SIZE           (64 << 10)
-#define CONFIG_SYS_NO_FLASH
 #endif
 
 /*
  * Network & Ethernet Configuration
  */
 #ifdef CONFIG_DRIVER_TI_EMAC
-#define CONFIG_EMAC_MDIO_PHY_NUM       7
 #define CONFIG_MII
 #undef CONFIG_DRIVER_TI_EMAC_USE_RMII
 #define CONFIG_BOOTP_DEFAULT
@@ -246,7 +240,6 @@
  * U-Boot general configuration
  */
 #define CONFIG_MISC_INIT_R
-#define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOOTFILE                "zImage" /* Boot file name */
 #define CONFIG_SYS_CBSIZE      1024 /* Console I/O Buffer Size */
 #define CONFIG_SYS_PBSIZE      (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
@@ -256,7 +249,6 @@
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
 #define CONFIG_MX_CYCLIC
 
 /*
@@ -266,36 +258,31 @@
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_REVISION_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS                "console=ttyS2,115200n8 root=/dev/mmcblk0p2 rw rootwait ip=off"
 #define CONFIG_BOOTCOMMAND \
-       "if mmc rescan; then " \
-               "run mmcboot; " \
-       "else " \
-               "run spiboot; " \
-       "fi"
-#define CONFIG_EXTRA_ENV_SETTINGS \
+               "run envboot; " \
+               "run mmcboot; "
+
+#define DEFAULT_LINUX_BOOT_ENV \
+       "loadaddr=0xc0700000\0" \
        "fdtaddr=0xc0600000\0" \
+       "scriptaddr=0xc0600000\0"
+
+#include <environment/ti/mmc.h>
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+       DEFAULT_LINUX_BOOT_ENV \
+       DEFAULT_MMC_TI_ARGS \
+       "bootpart=0:2\0" \
+       "bootdir=/boot\0" \
+       "bootfile=zImage\0" \
        "fdtfile=da850-lcdk.dtb\0" \
-       "fdtboot=bootz 0xc0700000 - ${fdtaddr};\0" \
-       "mmcboot=" \
-               "if fatload mmc 0 0xc0600000 boot.scr; then " \
-                       "source 0xc0600000; " \
-               "else " \
-                       "fatload mmc 0 0xc0700000 " \
-                               __stringify(CONFIG_BOOTFILE) "; " \
-                       "fatload mmc 0 ${fdtaddr} ${fdtfile}; " \
-                       "run fdtboot; " \
-               "fi;\0" \
-       "spiboot=" \
-               "sf probe 0; " \
-               "sf read 0xc0700000 0x80000 0x220000; " \
-               "bootz 0xc0700000;\0"
+       "boot_fdt=yes\0" \
+       "boot_fit=0\0" \
+       "console=ttyS2,115200n8\0"
 
 /*
  * U-Boot commands
  */
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_DIAG
 #define CONFIG_CMD_SAVES
 #ifdef CONFIG_CMD_BDI
 #define CONFIG_CLOCKS
@@ -319,16 +306,11 @@
        !defined(CONFIG_SYS_USE_NOR) && \
        !defined(CONFIG_USE_SPIFLASH)
 #define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_SYS_NO_FLASH
 #define CONFIG_ENV_SIZE                (16 << 10)
-#undef CONFIG_CMD_ENV
 #endif
 
 /* SD/MMC */
-#define CONFIG_GENERIC_MMC
-
 #ifdef CONFIG_MMC
-#define CONFIG_DOS_PARTITION
 #undef CONFIG_ENV_IS_IN_MMC
 #endif
 
@@ -345,7 +327,6 @@
 #ifndef CONFIG_DIRECT_NOR_BOOT
 /* defines for SPL */
 #define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SYS_SPL_MALLOC_START    (CONFIG_SYS_TEXT_BASE - \
                                                CONFIG_SYS_MALLOC_LEN)
 #define CONFIG_SYS_SPL_MALLOC_SIZE     CONFIG_SYS_MALLOC_LEN