Convert CONFIG_SYS_BOOTPARAMS_LEN to Kconfig

[J-u-boot.git] / common / Kconfig

diff --git a/common/Kconfig b/common/Kconfig
index 24c83f04e23415ca6f95e0606c6313778cbf437e..84db2e43f155c51c3692a6160e1564b899562a84 100644 (file)
--- a/common/Kconfig
+++ b/common/Kconfig
@@ -89,6 +89,15 @@ config TPL_LOGLEVEL
        int
        default LOGLEVEL
 
+config VPL_LOGLEVEL
+       int "loglevel for VPL"
+       default LOGLEVEL
+       help
+         All Messages with a loglevel smaller than the console loglevel will
+         be compiled in to VPL. See LOGLEVEL for a list of available log
+         levels. Setting this to a value above 4 may increase the code size
+         significantly.
+
 config SILENT_CONSOLE
        bool "Support a silent console"
        help
@@ -262,6 +271,15 @@ config LOG
 
 if LOG
 
+config VPL_LOG
+       bool "Enable logging support in VPL"
+       depends on LOG
+       help
+         This enables support for logging of status and debug messages. These
+         can be displayed on the console, recorded in a memory buffer, or
+         discarded if not needed. Logging supports various categories and
+         levels of severity.
+
 config LOG_MAX_LEVEL
        int "Maximum log level to record"
        default 6
@@ -431,6 +449,47 @@ config TPL_LOG_CONSOLE
 
 endif
 
+config VPL_LOG
+       bool "Enable logging support in VPL"
+       depends on LOG
+       help
+         This enables support for logging of status and debug messages. These
+         can be displayed on the console, recorded in a memory buffer, or
+         discarded if not needed. Logging supports various categories and
+         levels of severity.
+
+if VPL_LOG
+
+config VPL_LOG_MAX_LEVEL
+       int "Maximum log level to record in VPL"
+       default 3
+       help
+         This selects the maximum log level that will be recorded. Any value
+         higher than this will be ignored. If possible log statements below
+         this level will be discarded at build time. Levels:
+
+           0 - emergency
+           1 - alert
+           2 - critical
+           3 - error
+           4 - warning
+           5 - note
+           6 - info
+           7 - debug
+           8 - debug content
+           9 - debug hardware I/O
+
+config VPL_LOG_CONSOLE
+       bool "Allow log output to the console in VPL"
+       default y
+       help
+         Enables a log driver which writes log records to the console.
+         Generally the console is the serial port or LCD display. Only the
+         log message is shown - other details like level, category, file and
+         line number are omitted.
+
+endif
+
 config LOG_ERROR_RETURN
        bool "Log all functions which return an error"
        help
@@ -571,6 +630,10 @@ config BOARD_LATE_INIT
          So this config enable the late init code with the help of board_late_init
          function which should defined on respective boards.
 
+config CLOCKS
+       bool "Call set_cpu_clk_info"
+       depends on ARM
+
 config SYS_FSL_CLK
        bool
        depends on ARCH_LS1021A || FSL_LSCH2 || FSL_LSCH3 || \
@@ -596,6 +659,18 @@ config MISC_INIT_R
        help
          Enabling this option calls 'misc_init_r' function
 
+config SYS_MALLOC_BOOTPARAMS
+       bool "Malloc a buffer to use for bootparams"
+       help
+         In some cases rather than using a known location to store the
+         bi_boot_params portion of gd we need to allocate it from our malloc pool.
+
+config SYS_BOOTPARAMS_LEN
+       hex "Size of the bootparam buffer to malloc in bytes"
+       depends on SYS_MALLOC_BOOTPARAMS
+       default 0x20000 if MIPS || RCAR_GEN3
+       default 0x10000
+
 config ID_EEPROM
        bool "Enable I2C connected system identifier EEPROM"
        help
@@ -611,6 +686,12 @@ config PCI_INIT_R
          case of DM PCI-based Ethernet devices, which will not be detected
          without having the enumeration performed earlier.
 
+config RESET_PHY_R
+       bool "Reset ethernet PHY during init"
+       help
+         Implement reset_phy() in board code if required to reset the ethernet
+         PHY.
+
 endmenu
 
 endmenu                # Init options
@@ -752,7 +833,7 @@ config BLOBLIST
 
 config SPL_BLOBLIST
        bool "Support for a bloblist in SPL"
-       depends on BLOBLIST
+       depends on BLOBLIST && SPL_LIBGENERIC_SUPPORT && SPL_LIBCOMMON_SUPPORT
        default y if SPL
        help
          This enables a bloblist in SPL. If this is the first part of U-Boot
@@ -761,12 +842,20 @@ config SPL_BLOBLIST
 
 config TPL_BLOBLIST
        bool "Support for a bloblist in TPL"
-       depends on BLOBLIST
+       depends on BLOBLIST && TPL_LIBGENERIC_SUPPORT && TPL_LIBCOMMON_SUPPORT
        default y if TPL
        help
          This enables a bloblist in TPL. The bloblist is set up in TPL and
          passed to SPL and U-Boot proper.
 
+config VPL_BLOBLIST
+       bool "Support for a bloblist in VPL"
+       depends on BLOBLIST && VPL_LIBGENERIC_SUPPORT && VPL_LIBCOMMON_SUPPORT
+       default y if VPL
+       help
+         This enables a bloblist in VPL. The bloblist is set up in VPL and
+         passed to SPL and U-Boot proper.
+
 if BLOBLIST
 
 choice