#ifndef __CONFIG_H
#define __CONFIG_H
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
+
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 family */
#define CONFIG_QE 1 /* Has QE */
-#define CONFIG_MPC83xx 1 /* MPC83xx family */
#define CONFIG_MPC832x 1 /* MPC832x CPU specific */
#define CONFIG_SYS_TEXT_BASE 0xFE000000
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB)
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
- | (2 << BR_PS_SHIFT) /* 16 bit port */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */
+ | BR_PS_16 /* 16 bit port */ \
+ | BR_MS_GPCM /* MSEL = GPCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+ | OR_GPCM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_TRLX_SET \
+ | OR_GPCM_EHTR_SET \
+ | OR_GPCM_EAD)
+ /* 0xFE006FF7 */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
#undef CONFIG_SYS_FLASH_CHECKSUM
-/*
- * SDRAM on the Local Bus
- */
-#undef CONFIG_SYS_LB_SDRAM /* The board has not SRDAM on local bus */
-
-#ifdef CONFIG_SYS_LB_SDRAM
-#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base addr */
-#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000019 /* 64MB */
-
-/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */
-/*
- * Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
- *
- * For BR2, need:
- * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
- * port size = 32-bits = BR2[19:20] = 11
- * no parity checking = BR2[21:22] = 00
- * SDRAM for MSEL = BR2[24:26] = 011
- * Valid = BR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
- *
- * CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
- * the top 17 bits of BR2.
- */
-
- /*Port size=32bit, MSEL=SDRAM */
-#define CONFIG_SYS_BR2_PRELIM 0xf0001861
-
-/*
- * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
- *
- * For OR2, need:
- * 64MB mask for AM, OR2[0:7] = 1111 1100
- * XAM, OR2[17:18] = 11
- * 9 columns OR2[19-21] = 010
- * 13 rows OR2[23-25] = 100
- * EAD set for extra time OR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
- */
-
-#define CONFIG_SYS_OR2_PRELIM 0xfc006901
-
- /* LB sdram refresh timer, about 6us */
-#define CONFIG_SYS_LBC_LSRT 0x32000000
- /* LB refresh timer prescal, 266MHz/32 */
-#define CONFIG_SYS_LBC_MRTPR 0x20000000
-
-#define CONFIG_SYS_LBC_LSDMR_COMMON 0x0063b723
-
-#endif
-
-/*
- * Windows to access PIB via local bus
- */
- /* windows base 0xf8008000 */
-#define CONFIG_SYS_LBLAWBAR3_PRELIM 0xf8008000
-#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */
-
/*
* Serial Port
*/
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
/*
* Config on-board EEPROM
#define CONFIG_SYS_PCI1_IO_SIZE 0x04000000 /* 64M */
#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_SKIP_HOST_BRIDGE
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/*
* Command line configuration.
*/
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_EEPROM
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
-#if defined(CONFIG_SYS_RAMBOOT)
- #undef CONFIG_CMD_SAVEENV
- #undef CONFIG_CMD_LOADS
-#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
#if (CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
-#define XMK_STR(x) #x
-#define MK_STR(x) XMK_STR(x)
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=" CONFIG_NETDEV "\0" \
"uboot=" CONFIG_UBOOTPATH "\0" \
"tftpflash=tftp $loadaddr $uboot;" \
- "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "\
- "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
- "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; "\
- "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "\
- "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0"\
+ "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +$filesize; " \
+ "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +$filesize; " \
+ "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " $filesize; " \
+ "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +$filesize; " \
+ "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " $filesize\0" \
"fdtaddr=780000\0" \
"fdtfile=" CONFIG_FDTFILE "\0" \
"ramdiskaddr=1000000\0" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
-#undef MK_STR
-#undef XMK_STR
-
#endif /* __CONFIG_H */
projects / J-u-boot.git / blobdiff