wandboard: README: Include the mx6qp variant in the list

[J-u-boot.git] / include / configs / T102xRDB.h

diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h
index e5f03cc837eaa720a0d5ada1cb12fdb8d0be6a8f..f7a54f7a9733ef4288cf15e9fc1e1d27f9899474 100644 (file)
--- a/include/configs/T102xRDB.h
+++ b/include/configs/T102xRDB.h
@@ -1,7 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:     GPL-2.0+
  */
 
 /*
@@ -13,7 +12,6 @@
 
 /* High Level Configuration Options */
 #define CONFIG_SYS_BOOK3E_HV           /* Category E.HV supported */
-#define CONFIG_MP                      /* support multiple processors */
 #define CONFIG_ENABLE_36BIT_PHYS
 
 #ifdef CONFIG_PHYS_64BIT
@@ -34,8 +32,6 @@
 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xrdb/t1024_pbi.cfg
 #define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_TARGET              "u-boot-with-spl.bin"
-#define CONFIG_SYS_TEXT_BASE           0x30001000
 #define CONFIG_SPL_TEXT_BASE           0xFFFD8000
 #define CONFIG_SPL_PAD_TO              0x40000
 #define CONFIG_SPL_MAX_SIZE            0x28000
@@ -82,7 +78,6 @@
 
 #ifdef CONFIG_SDCARD
 #define CONFIG_RESET_VECTOR_ADDRESS    0x30000FFC
-#define CONFIG_SPL_MMC_MINIMAL
 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x30000000)
 #define CONFIG_SYS_MMC_U_BOOT_START    (0x30000000)
@@ -101,10 +96,6 @@
 
 #endif /* CONFIG_RAMBOOT_PBL */
 
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE   0xeff40000
-#endif
-
 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS    0xeffffffc
 #endif
@@ -160,7 +151,6 @@
 
 #if defined(CONFIG_SPIFLASH)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SPI_BUS             0
 #define CONFIG_ENV_SPI_CS              0
 #define CONFIG_ENV_SPI_MAX_HZ          10000000
@@ -174,13 +164,11 @@
 #endif
 #elif defined(CONFIG_SDCARD)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV         0
 #define CONFIG_ENV_SIZE                        0x2000
 #define CONFIG_ENV_OFFSET              (512 * 0x800)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE                        0x2000
 #if defined(CONFIG_TARGET_T1024RDB)
 #define CONFIG_ENV_OFFSET              (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
@@ -188,13 +176,11 @@
 #define CONFIG_ENV_OFFSET              (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #endif
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-#define CONFIG_ENV_IS_IN_REMOTE
 #define CONFIG_ENV_ADDR                0xffe20000
 #define CONFIG_ENV_SIZE                0x2000
 #elif defined(CONFIG_ENV_IS_NOWHERE)
 #define CONFIG_ENV_SIZE                0x2000
 #else
-#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
@@ -223,8 +209,6 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_SYS_MEMTEST_START       0x00200000 /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x00400000
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_PANIC_HANG      /* do not reset board on panic */
 
 /*
  *  Config the L3 Cache as L3 SRAM
@@ -238,7 +222,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SPL_RELOC_MALLOC_ADDR   (CONFIG_SPL_GD_ADDR + 12 * 1024)
 #define CONFIG_SPL_RELOC_MALLOC_SIZE   (30 << 10)
 #define CONFIG_SPL_RELOC_STACK         (CONFIG_SPL_GD_ADDR + 64 * 1024)
-#define CONFIG_SPL_RELOC_STACK_SIZE    (22 << 10)
 
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_DCSRBAR             0xf0000000
@@ -397,7 +380,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_NAND_DDR_LAW                11
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_CMD_NAND
 
 #if defined(CONFIG_NAND)
 #define CONFIG_SYS_CSPR0_EXT           CONFIG_SYS_NAND_CSPR_EXT
@@ -445,9 +427,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_RAMBOOT
 #endif
 
-#define CONFIG_BOARD_EARLY_INIT_R
-#define CONFIG_MISC_INIT_R
-
 #define CONFIG_HWCONFIG
 
 /* define to use L1 as initial stack */
@@ -476,7 +455,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_MALLOC_LEN          (10 * 1024 * 1024)
 
 /* Serial Port */
-#define CONFIG_CONS_INDEX      1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         (get_bus_freq(0)/2)
@@ -649,13 +627,11 @@ unsigned long get_board_ddr_clk(void);
  * SDHC
  */
 #ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #endif
 
 /* Qman/Bman */
 #ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN          /* Support Q/Bman */
 #define CONFIG_SYS_BMAN_NUM_PORTALS    10
 #define CONFIG_SYS_BMAN_MEM_BASE       0xf4000000
 #ifdef CONFIG_PHYS_64BIT
@@ -759,25 +735,14 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 #ifdef CONFIG_FMAN_ENET
-#define CONFIG_MII             /* MII PHY management */
 #define CONFIG_ETHPRIME                "FM1@DTSEC4"
-#define CONFIG_PHY_GIGE                /* Include GbE speed/duplex detection */
 #endif
 
 /*
  * Dynamic MTD Partition support with mtdparts
  */
 #ifdef CONFIG_MTD_NOR_FLASH
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
-                       "spi0=spife110000.1"
-#define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
-                       "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \
-                       "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:" \
-                       "1m(uboot),5m(kernel),128k(dtb),-(user)"
 #endif
 
 /*
@@ -786,31 +751,10 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_LOADS_ECHO              /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   /* allow baudrate change */
 
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#endif
-
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_LONGHELP                    /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS     16              /* max number of command args */
-#define CONFIG_SYS_BARGSIZE  CONFIG_SYS_CBSIZE  /* Boot Argument Buffer Size */
 
 /*
  * For booting Linux, the board info and command line data
@@ -882,11 +826,6 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_BOOTCOMMAND     CONFIG_LINUX
 
-/* Hash command with SHA acceleration supported in hardware */
-#ifdef CONFIG_FSL_CAAM
-#define CONFIG_CMD_HASH
-#endif
-
 #include <asm/fsl_secure_boot.h>
 
 #endif /* __T1024RDB_H */