/*
* High Level Configuration Options
*/
-#define CONFIG_KM_BOARD_NAME "tuxx1"
#define CONFIG_HOSTNAME "tuxx1"
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE /* Has QE */
-#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0"
-
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR 0xE0000000
-
-/*
- * Bus Arbitration Configuration Register (ACR)
- */
-#define CONFIG_SYS_ACR_PIPE_DEP 3 /* pipeline depth 4 transactions */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* 4 consecutive transactions */
-#define CONFIG_SYS_ACR_APARK 0 /* park bus to master (below) */
-#define CONFIG_SYS_ACR_PARKM 3 /* parking master = QuiccEngine */
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_256MB)
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
- BR_PS_16 | /* 16 bit port size */ \
- BR_MS_GPCM | /* MSEL = GPCM */ \
- BR_V)
-
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
- OR_GPCM_SCY_5 | \
- OR_GPCM_TRLX_SET | OR_GPCM_EAD)
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_KMBEC_FPGA_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_128MB)
-
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_KMBEC_FPGA_BASE | \
- BR_PS_8 | /* 8 bit port size */ \
- BR_MS_GPCM | /* MSEL = GPCM */ \
- BR_V)
-#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_KMBEC_FPGA_SIZE) | \
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
- OR_GPCM_SCY_2 | \
- OR_GPCM_TRLX_SET | OR_GPCM_EAD)
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2 HID2_HBE
-
-/*
- * MMU Setup
- */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-
-/* PRIO1, PIGGY: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_KMBEC_FPGA_BASE | BATL_PP_RW | \
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_KMBEC_FPGA_BASE | BATU_BL_128M | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT2L (CONFIG_SYS_KMBEC_FPGA_BASE | BATL_PP_RW | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_WR_CFG | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP 0x80000000
-#define CONFIG_SYS_LCRR_EADC 0x00010000
-#define CONFIG_SYS_LCRR_CLKDIV 0x00000002
-
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-
-/*
- * MMU Setup
- */
-#define CONFIG_SYS_IBAT7L (0)
-#define CONFIG_SYS_IBAT7U (0)
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
-#define CONFIG_SYS_APP1_BASE 0xA0000000 /* PAXG */
-#define CONFIG_SYS_APP1_SIZE 256 /* Megabytes */
-#define CONFIG_SYS_APP2_BASE 0xB0000000 /* PINC3 */
-#define CONFIG_SYS_APP2_SIZE 256 /* Megabytes */
-
-/*
- * Init Local Bus Memory Controller:
- * Device on board
- * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE
- * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit)
- *
- * Device on board (continued)
- * Bank Bus Machine PortSz Size KMTEPR2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB NVRAM
- * 3 Local GPCM 8 bit 256MB TEP2 (16 bit)
- */
-
-/*
- * Configuration for C2 on the local bus
- */
-/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_APP1_BASE
-/* Window size: 256 MB */
-#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_256MB)
-
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_APP1_BASE | \
- BR_PS_8 | \
- BR_MS_GPCM | \
- BR_V)
-
-#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_APP1_SIZE) | \
- OR_GPCM_CSNT | \
- OR_GPCM_ACS_DIV4 | \
- OR_GPCM_SCY_2 | \
- OR_GPCM_TRLX_SET | \
- OR_GPCM_EHTR_CLEAR | \
- OR_GPCM_EAD)
-
-/*
- * Configuration for C3 on the local bus
- */
-/* Access window base at PINC3 base */
-#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_APP2_BASE
-/* Window size: 256 MB */
-#define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_256MB)
-
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_APP2_BASE | \
- BR_PS_8 | \
- BR_MS_GPCM | \
- BR_V)
-
-#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_APP2_SIZE) | \
- OR_GPCM_CSNT | \
- OR_GPCM_ACS_DIV2 | \
- OR_GPCM_SCY_2 | \
- OR_GPCM_TRLX_SET | \
- OR_GPCM_EHTR_CLEAR)
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
#define CONFIG_SYS_MAMR (MxMR_GPL_x4DIS | \
0x0000c000 | \
MxMR_WLFx_2X)
-/*
- * MMU Setup
- */
-/* APP1: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_APP1_BASE | \
- BATL_PP_RW | \
- BATL_MEMCOHERENCE)
-/* 512M should also include APP2... */
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_APP1_BASE | \
- BATU_BL_256M | \
- BATU_VS | \
- BATU_VP)
-#define CONFIG_SYS_DBAT5L (CONFIG_SYS_APP1_BASE | \
- BATL_PP_RW | \
- BATL_CACHEINHIBIT | \
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-
-/* APP2: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT6L (CONFIG_SYS_APP2_BASE | \
- BATL_PP_RW | \
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U (CONFIG_SYS_APP2_BASE | \
- BATU_BL_256M | \
- BATU_VS | \
- BATU_VP)
-#define CONFIG_SYS_DBAT6L (CONFIG_SYS_APP2_BASE | \
- BATL_PP_RW | \
- BATL_CACHEINHIBIT | \
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-
-#define CONFIG_SYS_IBAT7L (0)
-#define CONFIG_SYS_IBAT7U (0)
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
#endif /* __CONFIG_H */
projects / J-u-boot.git / blobdiff