common: Add DISPLAY_BOARDINFO

[J-u-boot.git] / include / configs / UCP1020.h

diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h
index 76611b079932057839f568278005cd0d608bf520..d62c9b3163403e27bdf57a5f7152842d20f76b7e 100644 (file)
--- a/include/configs/UCP1020.h
+++ b/include/configs/UCP1020.h
@@ -14,9 +14,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_DISPLAY_BOARDINFO
-
 #define CONFIG_FSL_ELBC
 #define CONFIG_PCI
 #define CONFIG_PCIE1   /* PCIE controller 1 (slot 1) */
@@ -330,7 +327,6 @@
  */
 #define CONFIG_CONS_INDEX              1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -344,20 +340,6 @@
 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR + 0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR + 0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
@@ -381,13 +363,7 @@
  * eSPI - Enhanced SPI
  */
 #define CONFIG_HARD_SPI
-#define CONFIG_FSL_ESPI
 
-#define CONFIG_SPI_FLASH_SST           1
-#define CONFIG_SPI_FLASH_STMICRO       1
-#define CONFIG_SPI_FLASH_WINBOND       1
-#define CONFIG_CMD_SF                  1
-#define CONFIG_CMD_SPI                 1
 #define CONFIG_SF_DEFAULT_SPEED                10000000
 #define CONFIG_SF_DEFAULT_MODE         SPI_MODE_0
 
@@ -420,7 +396,6 @@
 #define CONFIG_SYS_PCIE1_IO_SIZE       0x00010000      /* 64k */
 
 #define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_E1000   /* Defind e1000 pci Ethernet card*/
 #define CONFIG_CMD_PCI
 
 #define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
@@ -491,19 +466,11 @@
  * Command line configuration.
  */
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_ERRATA
 #define CONFIG_CMD_CRAMFS
-#define CONFIG_CRAMFS_CMDLINE
 
 /*
  * USB
@@ -516,10 +483,8 @@
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 
 #ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
 #endif
 #endif
 
@@ -528,20 +493,16 @@
 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_CMD_MMC
 #define CONFIG_MMC_SPI
 #define CONFIG_CMD_MMC_SPI
 #define CONFIG_GENERIC_MMC
 #endif
 
 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA)
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
 #endif
 
 /* Misc Extra Settings */
-#define CONFIG_CMD_GPIO                        1
 #undef CONFIG_WATCHDOG /* watchdog disabled */
 
 /*
@@ -588,7 +549,6 @@
 #error "UCP1020 module revision is not defined !!!"
 #endif
 
-#define CONFIG_CMD_DHCP
 #define CONFIG_BOOTP_SERVERIP
 
 #define CONFIG_MII             /* MII PHY management */
@@ -627,7 +587,6 @@
 
 #if defined(CONFIG_DONGLE)
 
-#define CONFIG_BOOTDELAY 1     /* autoboot after 1 seconds */
 #define        CONFIG_EXTRA_ENV_SETTINGS                                       \
 "bootcmd=run prog_spi_mbrbootcramfs\0"                                 \
 "bootfile=uImage\0"                                                    \
@@ -757,7 +716,6 @@
 
 #if defined(CONFIG_UCP1020T1)
 
-#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
 #define        CONFIG_EXTRA_ENV_SETTINGS                                       \
 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \
 "bootfile=uImage\0"                                                    \
@@ -847,7 +805,6 @@
 
 #else /* For Arcturus Modules */
 
-#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
 #define        CONFIG_EXTRA_ENV_SETTINGS                                       \
 "bootcmd=run norkernel\0"                                              \
 "bootfile=uImage\0"                                                    \