*
* Configuration settings for the MX31ADS Freescale board.
*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/arch/mx31-regs.h>
+#include <asm/arch/imx-regs.h>
/* High Level Configuration Options */
-#define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */
-#define CONFIG_MX31 1 /* in a mx31 */
-#define CONFIG_MX31_HCLK_FREQ 26000000 /* RedBoot says 26MHz */
-#define CONFIG_MX31_CLK32 32768
+#define CONFIG_MX31 1 /* This is a mx31 */
+
+#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_SYS_TEXT_BASE 0xA0000000
+
+#define CONFIG_MACH_TYPE MACH_TYPE_MX31ADS
+
/*
* Disabled for now due to build problems under Debian and a significant increase
* in the final file size: 144260 vs. 109536 Bytes.
/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
/*
* Hardware drivers
*/
-#define CONFIG_MX31_UART 1
-#define CFG_MX31_UART1 1
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
#define CONFIG_HARD_SPI 1
#define CONFIG_MXC_SPI 1
#define CONFIG_DEFAULT_SPI_BUS 1
-#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH)
-
-#define CONFIG_RTC_MC13783 1
+#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_MXC_GPIO
+
+/* PMIC Controller */
+#define CONFIG_POWER
+#define CONFIG_POWER_SPI
+#define CONFIG_POWER_FSL
+#define CONFIG_FSL_PMIC_BUS 1
+#define CONFIG_FSL_PMIC_CS 0
+#define CONFIG_FSL_PMIC_CLK 1000000
+#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_FSL_PMIC_BITLEN 32
+#define CONFIG_RTC_MC13XXX
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/***********************************************************
* Command definition
***********************************************************/
-
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SPI
"cp.b ${loadaddr} ${uboot_addr} ${filesize}; " \
"setenv filesize; saveenv\0"
-#define CONFIG_DRIVER_CS8900 1
-#define CS8900_BASE 0xb4020300
-#define CS8900_BUS16 1 /* follow the Linux driver */
+#define CONFIG_CS8900
+#define CONFIG_CS8900_BASE 0xb4020300
+#define CONFIG_CS8900_BUS16 1 /* follow the Linux driver */
/*
* The MX31ADS board seems to have a hardware "peculiarity" confirmed under
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> "
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0 /* memtest works on */
-#define CFG_MEMTEST_END 0x10000
+#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x10000
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
-#define CFG_LOAD_ADDR CONFIG_LOADADDR
-
-#define CFG_HZ CONFIG_MX31_CLK32 /* use 32kHz clock as source */
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_CMDLINE_EDITING 1
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 CSD0_BASE
#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
+#define CONFIG_BOARD_EARLY_INIT_F
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_GBL_DATA_OFFSET)
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_FLASH_BASE CS0_BASE
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 262 /* max number of sectors on one chip */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE /* Monitor at beginning of flash */
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256KiB */
+#define CONFIG_SYS_FLASH_BASE CS0_BASE
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 262 /* max number of sectors on one chip */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256KiB */
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE (32 * 1024)
+#define CONFIG_ENV_SECT_SIZE (128 * 1024)
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-/* S29WS256N NOR flash has 4 32KiB small sectors at the beginning and at the end.
- * The rest of 32MiB is in 128KiB big sectors. U-Boot occupies the low 4 sectors,
- * if we put environment next to it, we will have to occupy 128KiB for it.
- * Putting it at the top of flash we use only 32KiB. */
-#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CONFIG_ENV_SECT_SIZE)
/*-----------------------------------------------------------------------
* CFI FLASH driver setup
*/
-#define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */
#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
#define CONFIG_FLASH_SPANSION_S29WS_N 1 /* A non-standard buffered write algorithm */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
-#define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */
/*
* JFFS2 partitions
*/
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
#endif /* __CONFIG_H */
projects / J-u-boot.git / blobdiff