Added 64-bit MMIO accessors for ARMv8

[J-u-boot.git] / include / configs / korat.h

diff --git a/include/configs/korat.h b/include/configs/korat.h
index 66cb53337d6d8b01401ccc53b5cc2f1ed50a7f63..5494a6007dfb32c8903b388520d4a4d3456ade11 100644 (file)
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -9,20 +9,7 @@
  * Jacqueline Pira-Ferriol, AMCC/IBM, [email protected]
  * Alain Saurel,            AMCC/IBM, [email protected]
  *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /*
@@ -35,7 +22,6 @@
  * High Level Configuration Options
  */
 #define CONFIG_440EPX          1       /* Specific PPC440EPx           */
-#define CONFIG_4xx             1       /* ... PPC4xx family            */
 #define CONFIG_SYS_CLK_FREQ    33333333
 
 #ifdef CONFIG_KORAT_PERMANENT
@@ -102,7 +88,6 @@
 #define CONFIG_SYS_NS16550_CLK         get_serial_clock()
 #define CONFIG_SYS_EXT_SERIAL_CLOCK    11059200        /* ext. 11.059MHz clk   */
 #define CONFIG_BAUDRATE                115200
-#define CONFIG_SERIAL_MULTI    1
 
 #define CONFIG_SYS_BAUDRATE_TABLE                                              \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
@@ -156,11 +141,11 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C                1       /* I2C with hardware support    */
-#undef CONFIG_SOFT_I2C                 /* I2C bit-banged               */
-#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
-#define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed and slave address  */
-#define CONFIG_SYS_I2C_SLAVE           0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0          400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0          0x7F
 
 #define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR     (0xa8>>1)
@@ -250,7 +235,6 @@
 #define CONFIG_HAS_ETH0
 #define CONFIG_SYS_RX_ETH_BUFFER       32      /* Number of ethernet rx        */
                                        /*   buffers & descriptors      */
-#define CONFIG_NET_MULTI       1
 #define CONFIG_HAS_ETH1                1       /* add support for "eth1addr"   */
 #define CONFIG_PHY1_ADDR       3
 
@@ -322,7 +306,6 @@
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory         */
-#define CONFIG_SYS_PROMPT              "=> "   /* Monitor Command Prompt       */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE              1024    /* Console I/O Buffer Size      */
 #else
@@ -339,8 +322,6 @@
 #define CONFIG_SYS_LOAD_ADDR           0x100000  /* default load address       */
 #define CONFIG_SYS_EXTBDINFO           1  /* To use extended board_into (bd_t) */
 
-#define CONFIG_SYS_HZ                  1000    /* decrementer freq: 1 ms ticks */
-
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history     */
 #define CONFIG_LOOPW           1       /* enable loopw command         */
 #define CONFIG_MX_CYCLIC       1       /* enable mdc/mwc commands      */
@@ -357,6 +338,7 @@
  */
 /* General PCI */
 #define CONFIG_PCI                     /* include pci support          */
+#define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play         */
 #define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0       /* to avoid problems with PNP   */
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup  */
@@ -559,7 +541,6 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use     */
 #endif
 
 /* Pass open firmware flat tree */