#define CONFIG_440 1
#define CONFIG_440GX 1 /* 440 GX */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* Disable-takes long time! */
+#undef CONFIG_SYS_DRAM_TEST /* Disable-takes long time! */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
/* POST support */
-#define CONFIG_POST (CFG_POST_RTC | \
- CFG_POST_I2C)
+#define CONFIG_POST (CONFIG_SYS_POST_RTC | \
+ CONFIG_SYS_POST_I2C)
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xfff80000 /* start of FLASH */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE /* start of monitor */
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
-#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
-#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* start of monitor */
+#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
+#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */
+#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
-#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000)
-#define CFG_GPIO_BASE (CFG_PERIPHERAL_BASE + 0x00000700)
+#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
+#define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
#define USR_LED0 0x00000080
#define USR_LED1 0x00000100
extern unsigned long in32(unsigned int);
extern void out32(unsigned int, unsigned long);
-#define LED0_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED0))
-#define LED1_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED1))
-#define LED2_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED2))
-#define LED3_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED3))
+#define LED0_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED0))
+#define LED1_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED1))
+#define LED2_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED2))
+#define LED3_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED3))
-#define LED0_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED0))
-#define LED1_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED1))
-#define LED2_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED2))
-#define LED3_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED3))
+#define LED0_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED0))
+#define LED1_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED1))
+#define LED2_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED2))
+#define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3))
#endif
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM)
*----------------------------------------------------------------------*/
-#define CFG_TEMP_STACK_OCM 1
-#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE
-#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
-#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
/*-----------------------------------------------------------------------
* Serial Port
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_BAUDRATE 9600
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
/*-----------------------------------------------------------------------
* The DS1743 code assumes this condition (i.e. -- it assumes the base
* address for the RTC registers is:
*
- * CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE
+ * CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE
*
*----------------------------------------------------------------------*/
/* TBS: Xpedite 1000 has STMicro M41T00 via IIC */
#define CONFIG_RTC_M41T11 1
-#define CFG_I2C_RTC_ADDR 0x68
-#define CFG_M41T11_BASE_YEAR 2000
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR 2000
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 8 /* sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 8 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7f
-#define CFG_I2C_NOPROBES {0x55,0x56,0x57,0x58,0x59,0x5a,0x5b,0x5c,0x69} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7f
+#define CONFIG_SYS_I2C_NOPROBES {0x55,0x56,0x57,0x58,0x59,0x5a,0x5b,0x5c,0x69} /* Don't probe these addrs */
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
-#define CFG_ENV_IS_IN_EEPROM 1
-#define CFG_ENV_SIZE 0x100 /* Size of Environment vars */
-#define CFG_ENV_OFFSET 0x100
-#define CFG_I2C_EEPROM_ADDR 0x50 /* this is actually the second page of the eeprom */
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_SIZE 0x100 /* Size of Environment vars */
+#define CONFIG_ENV_OFFSET 0x100
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* this is actually the second page of the eeprom */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_BOOTARGS "root=/dev/hda1 "
#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */
#define CONFIG_BAUDRATE 9600
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address phy0 not populated */
#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_HAS_ETH2 1 /* add support for "eth2addr" */
#define CONFIG_HAS_ETH3 1 /* add support for "eth3addr" */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_PCI | \
- CFG_CMD_IRQ | \
- CFG_CMD_I2C | \
- CFG_CMD_DATE | \
- CFG_CMD_BEDBUG | \
- CFG_CMD_EEPROM | \
- CFG_CMD_PING | \
- CFG_CMD_ELF | \
- CFG_CMD_MII | \
- CFG_CMD_DIAG | \
- CFG_CMD_FAT )
-/* CFG_CMD_DHCP | \ */
-/* CFG_CMD_KGDB | \ */
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_FAT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/*-----------------------------------------------------------------------
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
+#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
/* Board-specific PCI */
-#define CFG_PCI_TARGET_INIT /* let board init pci target */
+#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
-#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
-#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-#define CFG_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
+#define CONFIG_SYS_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 8192 /* For AMCC 440GX CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Internal Definitions
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
projects / J-u-boot.git / blobdiff