| | 1 | CONFIG_ARM=y |
| | 2 | CONFIG_ARCH_MX6=y |
| | 3 | CONFIG_SYS_TEXT_BASE=0x17800000 |
| | 4 | CONFIG_ENV_SIZE=0x2000 |
| | 5 | CONFIG_ENV_OFFSET=0xC0000 |
| | 6 | CONFIG_ENV_SECT_SIZE=0x2000 |
| | 7 | CONFIG_TARGET_NITROGEN6X=y |
| | 8 | CONFIG_DM_GPIO=y |
| | 9 | CONFIG_NR_DRAM_BANKS=1 |
| | 10 | CONFIG_CMD_HDMIDETECT=y |
| | 11 | CONFIG_AHCI=y |
| | 12 | # CONFIG_SYS_MALLOC_F is not set |
| | 13 | CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DDR_MB=1024" |
| | 14 | CONFIG_BOOTDELAY=3 |
| | 15 | CONFIG_USE_PREBOOT=y |
| | 16 | CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y |
| | 17 | CONFIG_SUPPORT_RAW_INITRD=y |
| | 18 | CONFIG_MISC_INIT_R=y |
| | 19 | CONFIG_BOUNCE_BUFFER=y |
| | 20 | CONFIG_BOARD_EARLY_INIT_F=y |
| | 21 | CONFIG_HUSH_PARSER=y |
| | 22 | CONFIG_CMD_BOOTZ=y |
| | 23 | CONFIG_CMD_MEMTEST=y |
| | 24 | CONFIG_SYS_ALT_MEMTEST=y |
| | 25 | CONFIG_SYS_MEMTEST_START=0x10000000 |
| | 26 | CONFIG_SYS_MEMTEST_END=0x10010000 |
| | 27 | # CONFIG_CMD_FLASH is not set |
| | 28 | CONFIG_CMD_GPIO=y |
| | 29 | CONFIG_CMD_I2C=y |
| | 30 | CONFIG_CMD_MMC=y |
| | 31 | CONFIG_CMD_USB=y |
| | 32 | CONFIG_CMD_USB_MASS_STORAGE=y |
| | 33 | CONFIG_CMD_DHCP=y |
| | 34 | CONFIG_CMD_MII=y |
| | 35 | CONFIG_CMD_PING=y |
| | 36 | CONFIG_CMD_BMP=y |
| | 37 | CONFIG_CMD_CACHE=y |
| | 38 | CONFIG_CMD_TIME=y |
| | 39 | CONFIG_CMD_EXT2=y |
| | 40 | CONFIG_CMD_EXT4=y |
| | 41 | CONFIG_CMD_EXT4_WRITE=y |
| | 42 | CONFIG_CMD_FAT=y |
| | 43 | CONFIG_CMD_FS_GENERIC=y |
| | 44 | CONFIG_OF_CONTROL=y |
| | 45 | CONFIG_DEFAULT_DEVICE_TREE="imx6dl-nitrogen6x" |
| | 46 | CONFIG_ENV_IS_IN_SPI_FLASH=y |
| | 47 | CONFIG_SYS_RELOC_GD_ENV_ADDR=y |
| | 48 | CONFIG_DM=y |
| | 49 | CONFIG_USB_FUNCTION_FASTBOOT=y |
| | 50 | CONFIG_FASTBOOT_BUF_ADDR=0x12000000 |
| | 51 | CONFIG_DM_MMC=y |
| | 52 | CONFIG_FSL_USDHC=y |
| | 53 | CONFIG_MTD=y |
| | 54 | CONFIG_DM_SPI_FLASH=y |
| | 55 | CONFIG_SF_DEFAULT_MODE=0 |
| | 56 | CONFIG_SF_DEFAULT_SPEED=25000000 |
| | 57 | CONFIG_SPI_FLASH_SST=y |
| | 58 | CONFIG_PHYLIB=y |
| | 59 | CONFIG_PHY_MICREL=y |
| | 60 | CONFIG_PHY_MICREL_KSZ90X1=y |
| | 61 | CONFIG_MII=y |
| | 62 | CONFIG_SPI=y |
| | 63 | CONFIG_DM_SPI=y |
| | 64 | CONFIG_MXC_SPI=y |
| | 65 | CONFIG_USB=y |
| | 66 | CONFIG_DM_USB=y |
| | 67 | CONFIG_USB_STORAGE=y |
| | 68 | CONFIG_USB_KEYBOARD=y |
| | 69 | CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y |
| | 70 | CONFIG_USB_GADGET=y |
| | 71 | CONFIG_USB_GADGET_MANUFACTURER="Boundary" |
| | 72 | CONFIG_USB_GADGET_VENDOR_NUM=0x0525 |
| | 73 | CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 |
| | 74 | CONFIG_CI_UDC=y |
| | 75 | CONFIG_USB_ETHER=y |
| | 76 | CONFIG_USB_ETH_CDC=y |
| | 77 | CONFIG_VIDEO_IPUV3=y |
| | 78 | CONFIG_VIDEO=y |
| | 79 | # CONFIG_VIDEO_SW_CURSOR is not set |
projects / J-u-boot.git / blame_incremental