[J-u-boot.git] / drivers / led / Kconfig

menu "LED Support"

config LED
	bool "Enable LED support"
	depends on DM
	help
	  Many boards have LEDs which can be used to signal status or alerts.
	  U-Boot provides a uclass API to implement this feature. LED drivers
	  can provide access to board-specific LEDs. Use of the device tree
	  for configuration is encouraged.

config LED_BCM6328
	bool "LED Support for BCM6328"
	depends on LED && ARCH_BMIPS
	help
	  This option enables support for LEDs connected to the BCM6328
	  LED HW controller accessed via MMIO registers.
	  HW blinking is supported and up to 24 LEDs can be controlled.
	  All LEDs can blink at the same time but the delay is shared, which
	  means that if one LED is set to blink at 100ms and then a different
	  LED is set to blink at 200ms, both will blink at 200ms.

config LED_BCM6358
	bool "LED Support for BCM6358"
	depends on LED && ARCH_BMIPS
	help
	  This option enables support for LEDs connected to the BCM6358
	  LED HW controller accessed via MMIO registers.
	  HW has no blinking capabilities and up to 32 LEDs can be controlled.

config LED_BCM6753
	bool "LED Support for BCM6753"
	depends on LED && BCM6855
	help
	  This option enables support for LEDs connected to the BCM6753
	  HW has blinking and fading capabilities and up to 32 LEDs can be controlled.

config LED_BCM6858
	bool "LED Support for BCM6858"
	depends on LED && (BCM6856 || BCM6858 || BCM63158)
	help
	  This option enables support for LEDs connected to the BCM6858
	  HW has blinking capabilities and up to 32 LEDs can be controlled.

config LED_CORTINA
	bool "LED Support for Cortina Access CAxxxx SoCs"
	depends on LED && (CORTINA_PLATFORM)
	help
	  This option enables support for LEDs connected to the Cortina
	  Access CAxxxx SOCs.

config LED_PWM
	bool "LED PWM"
	depends on LED && DM_PWM
	help
	  Enable support for LEDs connected to PWM.
	  Linux compatible ofdata.

config LED_BLINK
	bool "Support LED blinking"
	depends on LED
	help
	  Some drivers can support automatic blinking of LEDs with a given
	  period, without needing timers or extra code to handle the timing.
	  This option enables support for this which adds slightly to the
	  code size.

config SPL_LED
	bool "Enable LED support in SPL"
	depends on SPL_DM
	help
	  The LED subsystem adds a small amount of overhead to the image.
	  If this is acceptable and you have a need to use LEDs in SPL,
	  enable this option. You will need to enable device tree in SPL
	  for this to work.

config LED_GPIO
	bool "LED support for GPIO-connected LEDs"
	depends on LED && DM_GPIO
	help
	  Enable support for LEDs which are connected to GPIO lines. These
	  GPIOs may be on the SoC or some other device which provides GPIOs.
	  The GPIO driver must used driver model. LEDs are configured using
	  the device tree.

config SPL_LED_GPIO
	bool "LED support for GPIO-connected LEDs in SPL"
        depends on SPL_LED && SPL_DM_GPIO
	help
	  This option is an SPL-variant of the LED_GPIO option.
	  See the help of LED_GPIO for details.

config LED_STATUS
	bool "Enable status LED API"
	help
	  Allows common u-boot commands to use a board's leds to
	  provide status for activities like booting and downloading files.

if LED_STATUS

# Hidden constants

config LED_STATUS_OFF
	int
	default 0

config LED_STATUS_BLINKING
	int
	default 1

config LED_STATUS_ON
	int
	default 2

# Hidden constants end

config LED_STATUS_GPIO
	bool "GPIO status LED implementation"
	help
	  The status LED can be connected to a GPIO pin. In such cases, the
	  gpio_led driver can be used as a status LED backend implementation.

config LED_STATUS_BOARD_SPECIFIC
	bool "Specific board"
	default y
	help
	  LED support is only for a specific board.

comment "LEDs parameters"

config LED_STATUS0
	bool "Enable status LED 0"

if LED_STATUS0

config LED_STATUS_BIT
	int "identification"
	help
	  CONFIG_LED_STATUS_BIT is passed into the __led_* functions to identify
	  which LED is being acted on.  As such, the chosen value must be unique
	  with respect to the other CONFIG_LED_STATUS_BIT's. Mapping the value
	  to a physical LED is the responsibility of the __led_* function.

config LED_STATUS_STATE
	int "initial state"
	range LED_STATUS_OFF LED_STATUS_ON
	default LED_STATUS_OFF
	help
	  Should be set one of the following:
	  0 - off
	  1 - blinking
	  2 - on

config LED_STATUS_FREQ
	int "blink frequency"
	range 2 10
	default 2
	help
	  The LED blink period calculated from LED_STATUS_FREQ:
	  LED_STATUS_PERIOD = CONFIG_SYS_HZ/LED_STATUS_FREQ
	  Values range: 2 - 10

endif # LED_STATUS0

config LED_STATUS1
	bool "Enable status LED 1"

if LED_STATUS1

config LED_STATUS_BIT1
	int "identification"
	help
	  CONFIG_LED_STATUS_BIT1 is passed into the __led_* functions to
	  identify which LED is being acted on.  As such, the chosen value must
	  be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
	  the value to a physical LED is the responsibility of the __led_*
	  function.

config LED_STATUS_STATE1
	int "initial state"
	range LED_STATUS_OFF LED_STATUS_ON
	default LED_STATUS_OFF
	help
	  Should be set one of the following:
	  0 - off
	  1 - blinking
	  2 - on

config LED_STATUS_FREQ1
	int "blink frequency"
	range 2 10
	default 2
	help
	  The LED blink period calculated from LED_STATUS_FREQ1:
	  LED_STATUS_PERIOD1 = CONFIG_SYS_HZ/LED_STATUS_FREQ1
	  Values range: 2 - 10

endif # LED_STATUS1

config LED_STATUS2
	bool "Enable status LED 2"

if LED_STATUS2

config LED_STATUS_BIT2
	int "identification"
	help
	  CONFIG_LED_STATUS_BIT2 is passed into the __led_* functions to
	  identify which LED is being acted on.  As such, the chosen value must
	  be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
	  the value to a physical LED is the responsibility of the __led_*
	  function.

config LED_STATUS_STATE2
	int "initial state"
	range LED_STATUS_OFF LED_STATUS_ON
	default LED_STATUS_OFF
	help
	  Should be set one of the following:
	  0 - off
	  1 - blinking
	  2 - on

config LED_STATUS_FREQ2
	int "blink frequency"
	range 2 10
	default 2
	help
	  The LED blink period calculated from LED_STATUS_FREQ2:
	  LED_STATUS_PERIOD2 = CONFIG_SYS_HZ/LED_STATUS_FREQ2
	  Values range: 2 - 10

endif # LED_STATUS2

config LED_STATUS3
	bool "Enable status LED 3"

if LED_STATUS3

config LED_STATUS_BIT3
	int "identification"
	help
	  CONFIG_LED_STATUS_BIT3 is passed into the __led_* functions to
	  identify which LED is being acted on.  As such, the chosen value must
	  be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
	  the value to a physical LED is the responsibility of the __led_*
	  function.

config LED_STATUS_STATE3
	int "initial state"
	range LED_STATUS_OFF LED_STATUS_ON
	default LED_STATUS_OFF
	help
	  Should be set one of the following:
	  0 - off
	  1 - blinking
	  2 - on

config LED_STATUS_FREQ3
	int "blink frequency"
	range 2 10
	default 2
	help
	  The LED blink period calculated from LED_STATUS_FREQ3:
	  LED_STATUS_PERIOD3 = CONFIG_SYS_HZ/LED_STATUS_FREQ3
	  Values range: 2 - 10

endif # LED_STATUS3

config LED_STATUS4
	bool "Enable status LED 4"

if LED_STATUS4

config LED_STATUS_BIT4
	int "identification"
	help
	  CONFIG_LED_STATUS_BIT4 is passed into the __led_* functions to
	  identify which LED is being acted on.  As such, the chosen value must
	  be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
	  the value to a physical LED is the responsibility of the __led_*
	  function.

config LED_STATUS_STATE4
	int "initial state"
	range LED_STATUS_OFF LED_STATUS_ON
	default LED_STATUS_OFF
	help
	  Should be set one of the following:
	  0 - off
	  1 - blinking
	  2 - on

config LED_STATUS_FREQ4
	int "blink frequency"
	range 2 10
	default 2
	help
	  The LED blink period calculated from LED_STATUS_FREQ4:
	  LED_STATUS_PERIOD4 = CONFIG_SYS_HZ/LED_STATUS_FREQ4
	  Values range: 2 - 10

endif # LED_STATUS4

config LED_STATUS5
	bool "Enable status LED 5"

if LED_STATUS5

config LED_STATUS_BIT5
	int "identification"
	help
	  CONFIG_LED_STATUS_BIT5 is passed into the __led_* functions to
	  identify which LED is being acted on.  As such, the chosen value must
	  be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
	  the value to a physical LED is the responsibility of the __led_*
	  function.

config LED_STATUS_STATE5
	int "initial state"
	range LED_STATUS_OFF LED_STATUS_ON
	default LED_STATUS_OFF
	help
	  Should be set one of the following:
	  0 - off
	  1 - blinking
	  2 - on

config LED_STATUS_FREQ5
	int "blink frequency"
	range 2 10
	default 2
	help
	  The LED blink period calculated from LED_STATUS_FREQ5:
	  LED_STATUS_PERIOD5 = CONFIG_SYS_HZ/LED_STATUS_FREQ5
	  Values range: 2 - 10

endif # LED_STATUS5

config LED_STATUS_BOOT_ENABLE
	bool "Enable BOOT LED"
	help
	  Enable to turn an LED on when the board is booting.

if LED_STATUS_BOOT_ENABLE

config LED_STATUS_BOOT
	int "LED to light when the board is booting"
	help
	  Valid enabled LED device number.

endif # LED_STATUS_BOOT_ENABLE

config LED_STATUS_RED_ENABLE
	bool "Enable red LED"
	help
	  Enable red status LED.

if LED_STATUS_RED_ENABLE

config LED_STATUS_RED
	int "Red LED identification"
	help
	  Valid enabled LED device number.

endif # LED_STATUS_RED_ENABLE

config LED_STATUS_YELLOW_ENABLE
	bool "Enable yellow LED"
	help
	  Enable yellow status LED.

if LED_STATUS_YELLOW_ENABLE

config LED_STATUS_YELLOW
	int "Yellow LED identification"
	help
	  Valid enabled LED device number.

endif # LED_STATUS_YELLOW_ENABLE

config LED_STATUS_BLUE_ENABLE
	bool "Enable blue LED"
	help
	  Enable blue status LED.

if LED_STATUS_BLUE_ENABLE

config LED_STATUS_BLUE
	int "Blue LED identification"
	help
	  Valid enabled LED device number.

endif # LED_STATUS_BLUE_ENABLE

config LED_STATUS_GREEN_ENABLE
	bool "Enable green LED"
	help
	  Enable green status LED.

if LED_STATUS_GREEN_ENABLE

config LED_STATUS_GREEN
	int "Green LED identification"
	help
	  Valid enabled LED device number (0-5).

endif # LED_STATUS_GREEN_ENABLE

config LED_STATUS_CMD
	bool "Enable status LED commands"

endif # LED_STATUS

endmenu
Commit	Line	Data
0b11dbf7 MY	1	menu "LED Support"
0b11dbf7 MY	2
5917112c SG	3	config LED
	4	bool "Enable LED support"
	5	depends on DM
	6	help
	7	Many boards have LEDs which can be used to signal status or alerts.
	8	U-Boot provides a uclass API to implement this feature. LED drivers
	9	can provide access to board-specific LEDs. Use of the device tree
	10	for configuration is encouraged.
	11
28300dc5 ÁFR	12	config LED_BCM6328
	13	bool "LED Support for BCM6328"
	14	depends on LED && ARCH_BMIPS
	15	help
	16	This option enables support for LEDs connected to the BCM6328
	17	LED HW controller accessed via MMIO registers.
	18	HW blinking is supported and up to 24 LEDs can be controlled.
	19	All LEDs can blink at the same time but the delay is shared, which
	20	means that if one LED is set to blink at 100ms and then a different
	21	LED is set to blink at 200ms, both will blink at 200ms.
	22
632889cf ÁFR	23	config LED_BCM6358
	24	bool "LED Support for BCM6358"
	25	depends on LED && ARCH_BMIPS
	26	help
	27	This option enables support for LEDs connected to the BCM6358
	28	LED HW controller accessed via MMIO registers.
	29	HW has no blinking capabilities and up to 32 LEDs can be controlled.
	30
0d2001b1 PR	31	config LED_BCM6753
0d2001b1 PR	32	bool "LED Support for BCM6753"
8c1a9c7d	33	depends on LED && BCM6855
0d2001b1 PR	34	help
	35	This option enables support for LEDs connected to the BCM6753
	36	HW has blinking and fading capabilities and up to 32 LEDs can be controlled.
	37
d00c6a2d PR	38	config LED_BCM6858
d00c6a2d PR	39	bool "LED Support for BCM6858"
2dab3ee5	40	depends on LED && (BCM6856 \|\| BCM6858 \|\| BCM63158)
d00c6a2d PR	41	help
	42	This option enables support for LEDs connected to the BCM6858
	43	HW has blinking capabilities and up to 32 LEDs can be controlled.
	44
047e31ed JL	45	config LED_CORTINA
	46	bool "LED Support for Cortina Access CAxxxx SoCs"
	47	depends on LED && (CORTINA_PLATFORM)
	48	help
	49	This option enables support for LEDs connected to the Cortina
	50	Access CAxxxx SOCs.
	51
067cfc1c IV	52	config LED_PWM
	53	bool "LED PWM"
	54	depends on LED && DM_PWM
	55	help
	56	Enable support for LEDs connected to PWM.
	57	Linux compatible ofdata.
047e31ed	58
53378dac SG	59	config LED_BLINK
	60	bool "Support LED blinking"
	61	depends on LED
	62	help
	63	Some drivers can support automatic blinking of LEDs with a given
	64	period, without needing timers or extra code to handle the timing.
	65	This option enables support for this which adds slightly to the
	66	code size.
	67
f0cd2454	68	config SPL_LED
5917112c	69	bool "Enable LED support in SPL"
b340199f	70	depends on SPL_DM
5917112c SG	71	help
	72	The LED subsystem adds a small amount of overhead to the image.
	73	If this is acceptable and you have a need to use LEDs in SPL,
	74	enable this option. You will need to enable device tree in SPL
	75	for this to work.
9b36f748	76
5ac76bad SG	77	config LED_GPIO
	78	bool "LED support for GPIO-connected LEDs"
	79	depends on LED && DM_GPIO
	80	help
	81	Enable support for LEDs which are connected to GPIO lines. These
	82	GPIOs may be on the SoC or some other device which provides GPIOs.
	83	The GPIO driver must used driver model. LEDs are configured using
	84	the device tree.
0b11dbf7	85
6a436c91 SG	86	config SPL_LED_GPIO
6a436c91 SG	87	bool "LED support for GPIO-connected LEDs in SPL"
b340199f	88	depends on SPL_LED && SPL_DM_GPIO
6a436c91 SG	89	help
	90	This option is an SPL-variant of the LED_GPIO option.
	91	See the help of LED_GPIO for details.
	92
79267edd UM	93	config LED_STATUS
	94	bool "Enable status LED API"
	95	help
	96	Allows common u-boot commands to use a board's leds to
	97	provide status for activities like booting and downloading files.
	98
	99	if LED_STATUS
	100
	101	# Hidden constants
	102
	103	config LED_STATUS_OFF
	104	int
	105	default 0
	106
	107	config LED_STATUS_BLINKING
	108	int
	109	default 1
	110
	111	config LED_STATUS_ON
	112	int
	113	default 2
	114
	115	# Hidden constants end
	116
	117	config LED_STATUS_GPIO
	118	bool "GPIO status LED implementation"
	119	help
	120	The status LED can be connected to a GPIO pin. In such cases, the
	121	gpio_led driver can be used as a status LED backend implementation.
	122
	123	config LED_STATUS_BOARD_SPECIFIC
	124	bool "Specific board"
	125	default y
	126	help
	127	LED support is only for a specific board.
	128
	129	comment "LEDs parameters"
	130
	131	config LED_STATUS0
	132	bool "Enable status LED 0"
	133
	134	if LED_STATUS0
	135
	136	config LED_STATUS_BIT
	137	int "identification"
	138	help
	139	CONFIG_LED_STATUS_BIT is passed into the __led_* functions to identify
	140	which LED is being acted on. As such, the chosen value must be unique
	141	with respect to the other CONFIG_LED_STATUS_BIT's. Mapping the value
	142	to a physical LED is the responsibility of the __led_* function.
	143
	144	config LED_STATUS_STATE
	145	int "initial state"
	146	range LED_STATUS_OFF LED_STATUS_ON
	147	default LED_STATUS_OFF
	148	help
	149	Should be set one of the following:
	150	0 - off
	151	1 - blinking
	152	2 - on
	153
	154	config LED_STATUS_FREQ
	155	int "blink frequency"
	156	range 2 10
157	default 2
158	help
159	The LED blink period calculated from LED_STATUS_FREQ:
160	LED_STATUS_PERIOD = CONFIG_SYS_HZ/LED_STATUS_FREQ
161	Values range: 2 - 10
162
163	endif # LED_STATUS0
164
165	config LED_STATUS1
166	bool "Enable status LED 1"
167
168	if LED_STATUS1
169
170	config LED_STATUS_BIT1
171	int "identification"
172	help
173	CONFIG_LED_STATUS_BIT1 is passed into the __led_* functions to
174	identify which LED is being acted on. As such, the chosen value must
175	be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
176	the value to a physical LED is the responsibility of the __led_*
177	function.
178
179	config LED_STATUS_STATE1
180	int "initial state"
181	range LED_STATUS_OFF LED_STATUS_ON
182	default LED_STATUS_OFF
183	help
184	Should be set one of the following:
185	0 - off
186	1 - blinking
187	2 - on
188
189	config LED_STATUS_FREQ1
190	int "blink frequency"
191	range 2 10
192	default 2
193	help
194	The LED blink period calculated from LED_STATUS_FREQ1:
195	LED_STATUS_PERIOD1 = CONFIG_SYS_HZ/LED_STATUS_FREQ1
196	Values range: 2 - 10
197
198	endif # LED_STATUS1
199
200	config LED_STATUS2
201	bool "Enable status LED 2"
202
203	if LED_STATUS2
204
205	config LED_STATUS_BIT2
206	int "identification"
207	help
208	CONFIG_LED_STATUS_BIT2 is passed into the __led_* functions to
209	identify which LED is being acted on. As such, the chosen value must
210	be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
211	the value to a physical LED is the responsibility of the __led_*
212	function.
213
214	config LED_STATUS_STATE2
215	int "initial state"
216	range LED_STATUS_OFF LED_STATUS_ON
217	default LED_STATUS_OFF
218	help
219	Should be set one of the following:
220	0 - off
221	1 - blinking
222	2 - on
223
224	config LED_STATUS_FREQ2
225	int "blink frequency"
226	range 2 10
227	default 2
228	help
229	The LED blink period calculated from LED_STATUS_FREQ2:
230	LED_STATUS_PERIOD2 = CONFIG_SYS_HZ/LED_STATUS_FREQ2
231	Values range: 2 - 10
232
233	endif # LED_STATUS2
234
235	config LED_STATUS3
236	bool "Enable status LED 3"
237
238	if LED_STATUS3
239
240	config LED_STATUS_BIT3
241	int "identification"
242	help
243	CONFIG_LED_STATUS_BIT3 is passed into the __led_* functions to
244	identify which LED is being acted on. As such, the chosen value must
245	be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
246	the value to a physical LED is the responsibility of the __led_*
247	function.
248
249	config LED_STATUS_STATE3
250	int "initial state"
251	range LED_STATUS_OFF LED_STATUS_ON
252	default LED_STATUS_OFF
253	help
254	Should be set one of the following:
255	0 - off
256	1 - blinking
257	2 - on
258
259	config LED_STATUS_FREQ3
260	int "blink frequency"
261	range 2 10
262	default 2
263	help
264	The LED blink period calculated from LED_STATUS_FREQ3:
265	LED_STATUS_PERIOD3 = CONFIG_SYS_HZ/LED_STATUS_FREQ3
266	Values range: 2 - 10
267
268	endif # LED_STATUS3
269
270	config LED_STATUS4
271	bool "Enable status LED 4"
272
273	if LED_STATUS4
274
275	config LED_STATUS_BIT4
276	int "identification"
277	help
278	CONFIG_LED_STATUS_BIT4 is passed into the __led_* functions to
279	identify which LED is being acted on. As such, the chosen value must
280	be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
281	the value to a physical LED is the responsibility of the __led_*
282	function.
283
284	config LED_STATUS_STATE4
285	int "initial state"
286	range LED_STATUS_OFF LED_STATUS_ON
287	default LED_STATUS_OFF
288	help
289	Should be set one of the following:
290	0 - off
291	1 - blinking
292	2 - on
293
294	config LED_STATUS_FREQ4
295	int "blink frequency"
296	range 2 10
297	default 2
298	help
299	The LED blink period calculated from LED_STATUS_FREQ4:
300	LED_STATUS_PERIOD4 = CONFIG_SYS_HZ/LED_STATUS_FREQ4
301	Values range: 2 - 10
302
303	endif # LED_STATUS4
304
305	config LED_STATUS5
306	bool "Enable status LED 5"
307
308	if LED_STATUS5
309
310	config LED_STATUS_BIT5
311	int "identification"
312	help
313	CONFIG_LED_STATUS_BIT5 is passed into the __led_* functions to
314	identify which LED is being acted on. As such, the chosen value must
315	be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
316	the value to a physical LED is the responsibility of the __led_*
317	function.
318
319	config LED_STATUS_STATE5
320	int "initial state"
321	range LED_STATUS_OFF LED_STATUS_ON
322	default LED_STATUS_OFF
323	help
324	Should be set one of the following:
325	0 - off
326	1 - blinking
327	2 - on
328
329	config LED_STATUS_FREQ5
330	int "blink frequency"
331	range 2 10
332	default 2
333	help
334	The LED blink period calculated from LED_STATUS_FREQ5:
335	LED_STATUS_PERIOD5 = CONFIG_SYS_HZ/LED_STATUS_FREQ5
336	Values range: 2 - 10
337
338	endif # LED_STATUS5
339
340	config LED_STATUS_BOOT_ENABLE
341	bool "Enable BOOT LED"
342	help
343	Enable to turn an LED on when the board is booting.
344
345	if LED_STATUS_BOOT_ENABLE
346
347	config LED_STATUS_BOOT
348	int "LED to light when the board is booting"
349	help
350	Valid enabled LED device number.
351
352	endif # LED_STATUS_BOOT_ENABLE
353
354	config LED_STATUS_RED_ENABLE
355	bool "Enable red LED"
356	help
357	Enable red status LED.
358
359	if LED_STATUS_RED_ENABLE
360
361	config LED_STATUS_RED
362	int "Red LED identification"
363	help
364	Valid enabled LED device number.
365
366	endif # LED_STATUS_RED_ENABLE
367
368	config LED_STATUS_YELLOW_ENABLE
369	bool "Enable yellow LED"
370	help
371	Enable yellow status LED.
372
373	if LED_STATUS_YELLOW_ENABLE
374
375	config LED_STATUS_YELLOW
376	int "Yellow LED identification"
377	help
378	Valid enabled LED device number.
379
380	endif # LED_STATUS_YELLOW_ENABLE
381
382	config LED_STATUS_BLUE_ENABLE
383	bool "Enable blue LED"
384	help
385	Enable blue status LED.
386
387	if LED_STATUS_BLUE_ENABLE
388
389	config LED_STATUS_BLUE
390	int "Blue LED identification"
391	help
392	Valid enabled LED device number.
393
394	endif # LED_STATUS_BLUE_ENABLE
395
396	config LED_STATUS_GREEN_ENABLE
397	bool "Enable green LED"
398	help
399	Enable green status LED.
400
401	if LED_STATUS_GREEN_ENABLE
402
403	config LED_STATUS_GREEN
404	int "Green LED identification"
405	help
406	Valid enabled LED device number (0-5).
407
408	endif # LED_STATUS_GREEN_ENABLE
409
410	config LED_STATUS_CMD
411	bool "Enable status LED commands"
412
413	endif # LED_STATUS
414
0b11dbf7	415	endmenu