[J-u-boot.git] / include / configs / makalu.h

/*
 * Copyright (c) 2008 Nuovation System Designs, LLC
 *   Grant Erickson <[email protected]>
 *
 * (C) Copyright 2007-2008
 * Stefan Roese, DENX Software Engineering, [email protected].
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/************************************************************************
 * makalu.h - configuration for AMCC Makalu (405EX)
 ***********************************************************************/

#ifndef __CONFIG_H
#define __CONFIG_H

/*-----------------------------------------------------------------------
 * High Level Configuration Options
 *----------------------------------------------------------------------*/
#define CONFIG_MAKALU		1		/* Board is Makalu	*/
#define CONFIG_405EX		1		/* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ	33330000	/* ext frequency to pll	*/

#define	CONFIG_SYS_TEXT_BASE	0xFFFA0000

/*
 * Include common defines/options for all AMCC eval boards
 */
#define CONFIG_HOSTNAME	makalu
#define CONFIG_ADDMISC	"addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0"
#include "amcc-common.h"

#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
#define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/

/*-----------------------------------------------------------------------
 * Base addresses -- Note these are effective addresses where the
 * actual resources get mapped (not physical addresses)
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_BASE		0xFC000000
#define CONFIG_SYS_FPGA_BASE		0xF0000000

/*-----------------------------------------------------------------------
 * Initial RAM & Stack Pointer Configuration Options
 *
 *   There are traditionally three options for the primordial
 *   (i.e. initial) stack usage on the 405-series:
 *
 *      1) On-chip Memory (OCM) (i.e. SRAM)
 *      2) Data cache
 *      3) SDRAM
 *
 *   For the 405EX(r), there is no OCM, so we are left with (2) or (3)
 *   the latter of which is less than desireable since it requires
 *   setting up the SDRAM and ECC in assembly code.
 *
 *   To use (2), define 'CONFIG_SYS_INIT_DCACHE_CS' to be an unused chip
 *   select on the External Bus Controller (EBC) and then select a
 *   value for 'CONFIG_SYS_INIT_RAM_ADDR' outside of the range of valid,
 *   physical SDRAM. Otherwise, undefine 'CONFIG_SYS_INIT_DCACHE_CS' and
 *   select a value for 'CONFIG_SYS_INIT_RAM_ADDR' within the range of valid,
 *   physical SDRAM to use (3).
 *-----------------------------------------------------------------------*/

#define CONFIG_SYS_INIT_DCACHE_CS	4

#if defined(CONFIG_SYS_INIT_DCACHE_CS)
#define CONFIG_SYS_INIT_RAM_ADDR	(CONFIG_SYS_SDRAM_BASE + ( 1 << 30))	/*  1 GiB */
#else
#define CONFIG_SYS_INIT_RAM_ADDR	(CONFIG_SYS_SDRAM_BASE + (32 << 20))	/* 32 MiB */
#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */

#define CONFIG_SYS_INIT_RAM_SIZE        (4 << 10)			/*  4 KiB */
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

/*
 * If the data cache is being used for the primordial stack and global
 * data area, the POST word must be placed somewhere else. The General
 * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
 * its compare and mask register contents across reset, so it is used
 * for the POST word.
 */

#if defined(CONFIG_SYS_INIT_DCACHE_CS)
# define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
# define CONFIG_SYS_POST_WORD_ADDR	(CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
#else
# define CONFIG_SYS_INIT_EXTRA_SIZE	16
# define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE)
# define CONFIG_SYS_OCM_DATA_ADDR	CONFIG_SYS_INIT_RAM_ADDR
#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */

/*-----------------------------------------------------------------------
 * Serial Port
 *----------------------------------------------------------------------*/
#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
#undef CONFIG_SYS_EXT_SERIAL_CLOCK			/* no ext. clk		*/

/*-----------------------------------------------------------------------
 * Environment
 *----------------------------------------------------------------------*/
#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/

/*-----------------------------------------------------------------------
 * FLASH related
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_CFI			/* The flash is CFI compatible	*/
#define CONFIG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/

#define CONFIG_SYS_FLASH_BANKS_LIST    {CONFIG_SYS_FLASH_BASE}
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */

#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE	0x20000	/* size of one complete sector	*/
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
#endif /* CONFIG_ENV_IS_IN_FLASH */

/*-----------------------------------------------------------------------
 * DDR SDRAM
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_MBYTES_SDRAM        (256)		/* 256MB			*/

#define	CONFIG_SYS_SDRAM0_MB0CF_BASE	((  0 << 20) + CONFIG_SYS_SDRAM_BASE)
#define	CONFIG_SYS_SDRAM0_MB1CF_BASE	((128 << 20) + CONFIG_SYS_SDRAM_BASE)

/* DDR1/2 SDRAM Device Control Register Data Values */
#define CONFIG_SYS_SDRAM0_MB0CF	((CONFIG_SYS_SDRAM0_MB0CF_BASE >> 3)	| \
				 SDRAM_RXBAS_SDSZ_128MB 	| \
				 SDRAM_RXBAS_SDAM_MODE2 	| \
				 SDRAM_RXBAS_SDBE_ENABLE)
#define CONFIG_SYS_SDRAM0_MB1CF	((CONFIG_SYS_SDRAM0_MB1CF_BASE >> 3)	| \
				 SDRAM_RXBAS_SDSZ_128MB 	| \
				 SDRAM_RXBAS_SDAM_MODE2 	| \
				 SDRAM_RXBAS_SDBE_ENABLE)
#define CONFIG_SYS_SDRAM0_MB2CF	SDRAM_RXBAS_SDBE_DISABLE
#define CONFIG_SYS_SDRAM0_MB3CF	SDRAM_RXBAS_SDBE_DISABLE
#define CONFIG_SYS_SDRAM0_MCOPT1	0x04322000
#define CONFIG_SYS_SDRAM0_MCOPT2	0x00000000
#define CONFIG_SYS_SDRAM0_MODT0	0x01800000
#define CONFIG_SYS_SDRAM0_MODT1	0x00000000
#define CONFIG_SYS_SDRAM0_CODT		0x0080f837
#define CONFIG_SYS_SDRAM0_RTR		0x06180000
#define CONFIG_SYS_SDRAM0_INITPLR0	0xa8380000
#define CONFIG_SYS_SDRAM0_INITPLR1	0x81900400
#define CONFIG_SYS_SDRAM0_INITPLR2	0x81020000
#define CONFIG_SYS_SDRAM0_INITPLR3	0x81030000
#define CONFIG_SYS_SDRAM0_INITPLR4	0x81010404
#define CONFIG_SYS_SDRAM0_INITPLR5	0x81000542
#define CONFIG_SYS_SDRAM0_INITPLR6	0x81900400
#define CONFIG_SYS_SDRAM0_INITPLR7	0x8D080000
#define CONFIG_SYS_SDRAM0_INITPLR8	0x8D080000
#define CONFIG_SYS_SDRAM0_INITPLR9	0x8D080000
#define CONFIG_SYS_SDRAM0_INITPLR10	0x8D080000
#define CONFIG_SYS_SDRAM0_INITPLR11	0x81000442
#define CONFIG_SYS_SDRAM0_INITPLR12	0x81010780
#define CONFIG_SYS_SDRAM0_INITPLR13	0x81010400
#define CONFIG_SYS_SDRAM0_INITPLR14	0x00000000
#define CONFIG_SYS_SDRAM0_INITPLR15	0x00000000
#define CONFIG_SYS_SDRAM0_RQDC		0x80000038
#define CONFIG_SYS_SDRAM0_RFDC		0x00000209
#define CONFIG_SYS_SDRAM0_RDCC		0x40000000
#define CONFIG_SYS_SDRAM0_DLCR		0x030000a5
#define CONFIG_SYS_SDRAM0_CLKTR	0x80000000
#define CONFIG_SYS_SDRAM0_WRDTR	0x00000000
#define CONFIG_SYS_SDRAM0_SDTR1	0x80201000
#define CONFIG_SYS_SDRAM0_SDTR2	0x32204232
#define CONFIG_SYS_SDRAM0_SDTR3	0x080b0d1a
#define CONFIG_SYS_SDRAM0_MMODE	0x00000442
#define CONFIG_SYS_SDRAM0_MEMODE	0x00000404

/*-----------------------------------------------------------------------
 * I2C
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000

#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	6	/* 24C02 requires 5ms delay */
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52	/* I2C boot EEPROM (24C02BN)	*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/

/* Standard DTT sensor configuration */
#define CONFIG_DTT_DS1775	1
#define CONFIG_DTT_SENSORS	{ 0 }
#define CONFIG_SYS_I2C_DTT_ADDR	0x48

/* RTC configuration */
#define CONFIG_RTC_X1205	1
#define CONFIG_SYS_I2C_RTC_ADDR	0x6f

/*-----------------------------------------------------------------------
 * Ethernet
 *----------------------------------------------------------------------*/
#define CONFIG_M88E1111_PHY	1
#define CONFIG_IBM_EMAC4_V4	1
#define CONFIG_EMAC_PHY_MODE	EMAC_PHY_MODE_RGMII_RGMII
#define CONFIG_PHY_ADDR		6	/* PHY address, See schematics	*/

#define CONFIG_PHY_RESET	1	/* reset phy upon startup	*/
#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */

#define CONFIG_HAS_ETH0		1

#define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
#define CONFIG_PHY1_ADDR	0

/*
 * Default environment variables
 */
#define	CONFIG_EXTRA_ENV_SETTINGS					\
	CONFIG_AMCC_DEF_ENV						\
	CONFIG_AMCC_DEF_ENV_POWERPC					\
	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
	"kernel_addr=fc000000\0"					\
	"fdt_addr=fc1e0000\0"						\
	"ramdisk_addr=fc200000\0"					\
	"pciconfighost=1\0"						\
	"pcie_mode=RP:RP\0"						\
	""

/*
 * Commands additional to the ones defined in amcc-common.h
 */
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DTT
#define CONFIG_CMD_PCI

/* POST support */
#define CONFIG_POST		(CONFIG_SYS_POST_CACHE		| \
				 CONFIG_SYS_POST_CPU		| \
				 CONFIG_SYS_POST_ETHER		| \
				 CONFIG_SYS_POST_I2C		| \
				 CONFIG_SYS_POST_MEMORY	| \
				 CONFIG_SYS_POST_UART)

/* Define here the base-addresses of the UARTs to test in POST */
#define CONFIG_SYS_POST_UART_TABLE	{ CONFIG_SYS_NS16550_COM1, \
			CONFIG_SYS_NS16550_COM2 }

#define CONFIG_LOGBUFFER
#define CONFIG_SYS_POST_CACHE_ADDR	0x00800000 /* free virtual address	*/

#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */

/*-----------------------------------------------------------------------
 * PCI stuff
 *----------------------------------------------------------------------*/
#define CONFIG_PCI			/* include pci support	        */
#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
#define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
#define CONFIG_PCI_CONFIG_HOST_BRIDGE

/*-----------------------------------------------------------------------
 * PCIe stuff
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_PCIE_MEMBASE	0x90000000	/* mapped PCIe memory	*/
#define CONFIG_SYS_PCIE_MEMSIZE	0x08000000      /* 128 Meg, smallest incr per port */

#define	CONFIG_SYS_PCIE0_CFGBASE	0xa0000000      /* remote access */
#define	CONFIG_SYS_PCIE0_XCFGBASE	0xb0000000      /* local access */
#define	CONFIG_SYS_PCIE0_CFGMASK	0xe0000001      /* 512 Meg */

#define	CONFIG_SYS_PCIE1_CFGBASE	0xc0000000      /* remote access */
#define	CONFIG_SYS_PCIE1_XCFGBASE	0xd0000000      /* local access */
#define	CONFIG_SYS_PCIE1_CFGMASK	0xe0000001      /* 512 Meg */

#define	CONFIG_SYS_PCIE0_UTLBASE	0xef502000
#define	CONFIG_SYS_PCIE1_UTLBASE	0xef503000

/* base address of inbound PCIe window */
#define CONFIG_SYS_PCIE_INBOUND_BASE	0x0000000000000000ULL

/*-----------------------------------------------------------------------
 * External Bus Controller (EBC) Setup
 *----------------------------------------------------------------------*/
/* Memory Bank 0 (NOR-FLASH) initialization					*/
#define CONFIG_SYS_EBC_PB0AP		0x08033700
#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_FLASH_BASE | 0xda000)

/* Memory Bank 2 (CPLD) initialization						*/
#define CONFIG_SYS_EBC_PB2AP           0x9400C800
#define CONFIG_SYS_EBC_PB2CR           0xF0018000 /*  BAS=0x800,BS=1MB,BU=R/W,BW=8bit	*/

#define CONFIG_SYS_EBC_CFG		0x7FC00000 /*  EBC0_CFG */

/*-----------------------------------------------------------------------
 * GPIO Setup
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_4xx_GPIO_TABLE { /*	  Out		  GPIO	Alternate1	Alternate2	Alternate3 */ \
{											\
/* GPIO Core 0 */									\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO0	EBC_DATA_PAR(0)			*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO1	EBC_DATA_PAR(1)			*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO2	EBC_DATA_PAR(2)			*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO3	EBC_DATA_PAR(3)			*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO4	EBC_DATA(20)	USB2_DATA(4)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO5	EBC_DATA(21)	USB2_DATA(5)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO6	EBC_DATA(22)	USB2_DATA(6)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO7	EBC_DATA(23)	USB2_DATA(7)	*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	CS(1)/NFCE(1)	IRQ(7)		*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	CS(2)/NFCE(2)	IRQ(8)		*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3)	IRQ(9)		*/	\
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6)				*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16)	USB2_DATA(0)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17)	USB2_DATA(1)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18)	USB2_DATA(2)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19)	USB2_DATA(3)	*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD	UART1_CTS	*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR	UART1_RTS	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS			*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS			*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO20 UART0_DTR	UART1_TX	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO21 UART0_RI	UART1_RX	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ	DMA_ACK2	*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK	DMA_REQ2	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ	DMA_EOT2	IRQ(4) */ \
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK	DMA_ACK3	IRQ(3) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5)	DMA_EOT0	TS(3) */ \
{GPIO0_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ	DMA_EOT3	IRQ(5) */ \
{GPIO0_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO28				*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO29 DMA_EOT1	IRQ(2)		*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO30 DMA_REQ1	IRQ(1)		*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO31 DMA_ACK1	IRQ(0)		*/	\
}												\
}

#define CONFIG_SYS_GPIO_PCIE_RST	23
#define CONFIG_SYS_GPIO_PCIE_CLKREQ	27
#define CONFIG_SYS_GPIO_PCIE_WAKE	28

#endif	/* __CONFIG_H */
Commit	Line	Data
211ea91a	1	/*
8a24c07b GE	2	* Copyright (c) 2008 Nuovation System Designs, LLC
	3	* Grant Erickson <[email protected]>
	4	*
869d14b4	5	* (C) Copyright 2007-2008
211ea91a SR	6	* Stefan Roese, DENX Software Engineering, [email protected].
211ea91a SR	7	*
3765b3e7	8	* SPDX-License-Identifier: GPL-2.0+
211ea91a SR	9	*/
	10
	11	/************************************************************************
	12	* makalu.h - configuration for AMCC Makalu (405EX)
	13	***********************************************************************/
	14
	15	#ifndef __CONFIG_H
	16	#define __CONFIG_H
	17
	18	/*-----------------------------------------------------------------------
	19	* High Level Configuration Options
	20	----------------------------------------------------------------------/
	21	#define CONFIG_MAKALU 1 /* Board is Makalu */
211ea91a SR	22	#define CONFIG_405EX 1 /* Specifc 405EX support*/
	23	#define CONFIG_SYS_CLK_FREQ 33330000 /* ext frequency to pll */
	24
2ae18241 WD	25	#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
2ae18241 WD	26
490f2040 SR	27	/*
	28	* Include common defines/options for all AMCC eval boards
	29	*/
	30	#define CONFIG_HOSTNAME makalu
	31	#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0"
	32	#include "amcc-common.h"
	33
211ea91a SR	34	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
	35	#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
	36
	37	/*-----------------------------------------------------------------------
	38	* Base addresses -- Note these are effective addresses where the
	39	* actual resources get mapped (not physical addresses)
	40	----------------------------------------------------------------------/
6d0f6bcf JCPV	41	#define CONFIG_SYS_FLASH_BASE 0xFC000000
6d0f6bcf JCPV	42	#define CONFIG_SYS_FPGA_BASE 0xF0000000
211ea91a SR	43
211ea91a SR	44	/*-----------------------------------------------------------------------
8a24c07b GE	45	* Initial RAM & Stack Pointer Configuration Options
	46	*
	47	* There are traditionally three options for the primordial
	48	* (i.e. initial) stack usage on the 405-series:
	49	*
	50	* 1) On-chip Memory (OCM) (i.e. SRAM)
	51	* 2) Data cache
	52	* 3) SDRAM
	53	*
	54	* For the 405EX(r), there is no OCM, so we are left with (2) or (3)
	55	* the latter of which is less than desireable since it requires
	56	* setting up the SDRAM and ECC in assembly code.
	57	*
6d0f6bcf	58	* To use (2), define 'CONFIG_SYS_INIT_DCACHE_CS' to be an unused chip
8a24c07b	59	* select on the External Bus Controller (EBC) and then select a
6d0f6bcf JCPV	60	* value for 'CONFIG_SYS_INIT_RAM_ADDR' outside of the range of valid,
	61	* physical SDRAM. Otherwise, undefine 'CONFIG_SYS_INIT_DCACHE_CS' and
	62	* select a value for 'CONFIG_SYS_INIT_RAM_ADDR' within the range of valid,
8a24c07b GE	63	* physical SDRAM to use (3).
	64	-----------------------------------------------------------------------/
	65
6d0f6bcf	66	#define CONFIG_SYS_INIT_DCACHE_CS 4
8a24c07b	67
6d0f6bcf JCPV	68	#if defined(CONFIG_SYS_INIT_DCACHE_CS)
6d0f6bcf JCPV	69	#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */
8a24c07b	70	#else
6d0f6bcf JCPV	71	#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + (32 << 20)) /* 32 MiB */
6d0f6bcf JCPV	72	#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */
8a24c07b	73
553f0982	74	#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) /* 4 KiB */
25ddd1fb	75	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
211ea91a	76
8a24c07b GE	77	/*
	78	* If the data cache is being used for the primordial stack and global
	79	* data area, the POST word must be placed somewhere else. The General
	80	* Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
	81	* its compare and mask register contents across reset, so it is used
	82	* for the POST word.
	83	*/
	84
6d0f6bcf JCPV	85	#if defined(CONFIG_SYS_INIT_DCACHE_CS)
6d0f6bcf JCPV	86	# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
800eb096	87	# define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
8a24c07b	88	#else
6d0f6bcf JCPV	89	# define CONFIG_SYS_INIT_EXTRA_SIZE 16
6d0f6bcf JCPV	90	# define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE)
6d0f6bcf JCPV	91	# define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_INIT_RAM_ADDR
6d0f6bcf JCPV	92	#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */
211ea91a SR	93
	94	/*-----------------------------------------------------------------------
	95	* Serial Port
	96	----------------------------------------------------------------------/
550650dd	97	#define CONFIG_CONS_INDEX 1 /* Use UART0 */
6d0f6bcf	98	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no ext. clk */
211ea91a	99
211ea91a SR	100	/*-----------------------------------------------------------------------
	101	* Environment
	102	----------------------------------------------------------------------/
5a1aceb0	103	#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
211ea91a SR	104
	105	/*-----------------------------------------------------------------------
	106	* FLASH related
	107	----------------------------------------------------------------------/
6d0f6bcf	108	#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
00b1883a	109	#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
211ea91a	110
6d0f6bcf JCPV	111	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
	112	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	113	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
211ea91a	114
6d0f6bcf JCPV	115	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
6d0f6bcf JCPV	116	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
211ea91a	117
6d0f6bcf JCPV	118	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
6d0f6bcf JCPV	119	#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
211ea91a	120
5a1aceb0	121	#ifdef CONFIG_ENV_IS_IN_FLASH
0e8d1586	122	#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
6d0f6bcf	123	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
0e8d1586	124	#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
211ea91a SR	125
211ea91a SR	126	/* Address and size of Redundant Environment Sector */
0e8d1586 JCPV	127	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
0e8d1586 JCPV	128	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
5a1aceb0	129	#endif /* CONFIG_ENV_IS_IN_FLASH */
211ea91a SR	130
	131	/*-----------------------------------------------------------------------
	132	* DDR SDRAM
	133	----------------------------------------------------------------------/
6d0f6bcf	134	#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */
8a24c07b	135
6d0f6bcf JCPV	136	#define CONFIG_SYS_SDRAM0_MB0CF_BASE (( 0 << 20) + CONFIG_SYS_SDRAM_BASE)
6d0f6bcf JCPV	137	#define CONFIG_SYS_SDRAM0_MB1CF_BASE ((128 << 20) + CONFIG_SYS_SDRAM_BASE)
8a24c07b GE	138
8a24c07b GE	139	/* DDR1/2 SDRAM Device Control Register Data Values */
6d0f6bcf	140	#define CONFIG_SYS_SDRAM0_MB0CF ((CONFIG_SYS_SDRAM0_MB0CF_BASE >> 3) \| \
8a24c07b GE	141	SDRAM_RXBAS_SDSZ_128MB \| \
	142	SDRAM_RXBAS_SDAM_MODE2 \| \
	143	SDRAM_RXBAS_SDBE_ENABLE)
6d0f6bcf	144	#define CONFIG_SYS_SDRAM0_MB1CF ((CONFIG_SYS_SDRAM0_MB1CF_BASE >> 3) \| \
8a24c07b GE	145	SDRAM_RXBAS_SDSZ_128MB \| \
	146	SDRAM_RXBAS_SDAM_MODE2 \| \
	147	SDRAM_RXBAS_SDBE_ENABLE)
6d0f6bcf JCPV	148	#define CONFIG_SYS_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE
	149	#define CONFIG_SYS_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE
	150	#define CONFIG_SYS_SDRAM0_MCOPT1 0x04322000
	151	#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000
	152	#define CONFIG_SYS_SDRAM0_MODT0 0x01800000
	153	#define CONFIG_SYS_SDRAM0_MODT1 0x00000000
	154	#define CONFIG_SYS_SDRAM0_CODT 0x0080f837
	155	#define CONFIG_SYS_SDRAM0_RTR 0x06180000
	156	#define CONFIG_SYS_SDRAM0_INITPLR0 0xa8380000
	157	#define CONFIG_SYS_SDRAM0_INITPLR1 0x81900400
	158	#define CONFIG_SYS_SDRAM0_INITPLR2 0x81020000
	159	#define CONFIG_SYS_SDRAM0_INITPLR3 0x81030000
	160	#define CONFIG_SYS_SDRAM0_INITPLR4 0x81010404
	161	#define CONFIG_SYS_SDRAM0_INITPLR5 0x81000542
	162	#define CONFIG_SYS_SDRAM0_INITPLR6 0x81900400
	163	#define CONFIG_SYS_SDRAM0_INITPLR7 0x8D080000
	164	#define CONFIG_SYS_SDRAM0_INITPLR8 0x8D080000
	165	#define CONFIG_SYS_SDRAM0_INITPLR9 0x8D080000
	166	#define CONFIG_SYS_SDRAM0_INITPLR10 0x8D080000
	167	#define CONFIG_SYS_SDRAM0_INITPLR11 0x81000442
	168	#define CONFIG_SYS_SDRAM0_INITPLR12 0x81010780
	169	#define CONFIG_SYS_SDRAM0_INITPLR13 0x81010400
	170	#define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000
	171	#define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000
	172	#define CONFIG_SYS_SDRAM0_RQDC 0x80000038
	173	#define CONFIG_SYS_SDRAM0_RFDC 0x00000209
	174	#define CONFIG_SYS_SDRAM0_RDCC 0x40000000
	175	#define CONFIG_SYS_SDRAM0_DLCR 0x030000a5
	176	#define CONFIG_SYS_SDRAM0_CLKTR 0x80000000
	177	#define CONFIG_SYS_SDRAM0_WRDTR 0x00000000
	178	#define CONFIG_SYS_SDRAM0_SDTR1 0x80201000
	179	#define CONFIG_SYS_SDRAM0_SDTR2 0x32204232
	180	#define CONFIG_SYS_SDRAM0_SDTR3 0x080b0d1a
	181	#define CONFIG_SYS_SDRAM0_MMODE 0x00000442
	182	#define CONFIG_SYS_SDRAM0_MEMODE 0x00000404
211ea91a SR	183
	184	/*-----------------------------------------------------------------------
	185	* I2C
	186	----------------------------------------------------------------------/
880540de	187	#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
211ea91a	188
6d0f6bcf JCPV	189	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
	190	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
	191	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
211ea91a SR	192
	193	/* Standard DTT sensor configuration */
	194	#define CONFIG_DTT_DS1775 1
	195	#define CONFIG_DTT_SENSORS { 0 }
6d0f6bcf	196	#define CONFIG_SYS_I2C_DTT_ADDR 0x48
211ea91a SR	197
	198	/* RTC configuration */
	199	#define CONFIG_RTC_X1205 1
6d0f6bcf	200	#define CONFIG_SYS_I2C_RTC_ADDR 0x6f
211ea91a SR	201
	202	/*-----------------------------------------------------------------------
	203	* Ethernet
	204	----------------------------------------------------------------------/
	205	#define CONFIG_M88E1111_PHY 1
	206	#define CONFIG_IBM_EMAC4_V4 1
1740c1bf	207	#define CONFIG_EMAC_PHY_MODE EMAC_PHY_MODE_RGMII_RGMII
211ea91a SR	208	#define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */
	209
	210	#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
	211	#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
	212
	213	#define CONFIG_HAS_ETH0 1
	214
211ea91a	215	#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
ecdcbd4f	216	#define CONFIG_PHY1_ADDR 0
211ea91a	217
490f2040 SR	218	/*
	219	* Default environment variables
	220	*/
211ea91a	221	#define CONFIG_EXTRA_ENV_SETTINGS \
490f2040 SR	222	CONFIG_AMCC_DEF_ENV \
	223	CONFIG_AMCC_DEF_ENV_POWERPC \
	224	CONFIG_AMCC_DEF_ENV_PPC_OLD \
	225	CONFIG_AMCC_DEF_ENV_NOR_UPD \
ecdcbd4f	226	"kernel_addr=fc000000\0" \
869d14b4	227	"fdt_addr=fc1e0000\0" \
ecdcbd4f	228	"ramdisk_addr=fc200000\0" \
211ea91a SR	229	"pciconfighost=1\0" \
	230	"pcie_mode=RP:RP\0" \
	231	""
211ea91a SR	232
211ea91a SR	233	/*
490f2040	234	* Commands additional to the ones defined in amcc-common.h
211ea91a	235	*/
211ea91a	236	#define CONFIG_CMD_DATE
211ea91a	237	#define CONFIG_CMD_DTT
211ea91a	238	#define CONFIG_CMD_PCI
211ea91a SR	239
211ea91a SR	240	/* POST support */
6d0f6bcf JCPV	241	#define CONFIG_POST (CONFIG_SYS_POST_CACHE \| \
	242	CONFIG_SYS_POST_CPU \| \
	243	CONFIG_SYS_POST_ETHER \| \
	244	CONFIG_SYS_POST_I2C \| \
	245	CONFIG_SYS_POST_MEMORY \| \
	246	CONFIG_SYS_POST_UART)
211ea91a SR	247
211ea91a SR	248	/* Define here the base-addresses of the UARTs to test in POST */
5d7c73e6 SR	249	#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \
5d7c73e6 SR	250	CONFIG_SYS_NS16550_COM2 }
211ea91a SR	251
211ea91a SR	252	#define CONFIG_LOGBUFFER
6d0f6bcf	253	#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
211ea91a	254
6d0f6bcf	255	#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
211ea91a	256
211ea91a SR	257	/*-----------------------------------------------------------------------
	258	* PCI stuff
	259	----------------------------------------------------------------------/
	260	#define CONFIG_PCI /* include pci support */
842033e6	261	#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
211ea91a SR	262	#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
	263	#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
	264	#define CONFIG_PCI_CONFIG_HOST_BRIDGE
	265
	266	/*-----------------------------------------------------------------------
	267	* PCIe stuff
	268	----------------------------------------------------------------------/
6d0f6bcf JCPV	269	#define CONFIG_SYS_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */
6d0f6bcf JCPV	270	#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */
211ea91a	271
6d0f6bcf JCPV	272	#define CONFIG_SYS_PCIE0_CFGBASE 0xa0000000 /* remote access */
	273	#define CONFIG_SYS_PCIE0_XCFGBASE 0xb0000000 /* local access */
	274	#define CONFIG_SYS_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */
211ea91a	275
6d0f6bcf JCPV	276	#define CONFIG_SYS_PCIE1_CFGBASE 0xc0000000 /* remote access */
	277	#define CONFIG_SYS_PCIE1_XCFGBASE 0xd0000000 /* local access */
	278	#define CONFIG_SYS_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */
211ea91a	279
6d0f6bcf JCPV	280	#define CONFIG_SYS_PCIE0_UTLBASE 0xef502000
6d0f6bcf JCPV	281	#define CONFIG_SYS_PCIE1_UTLBASE 0xef503000
211ea91a SR	282
211ea91a SR	283	/* base address of inbound PCIe window */
6d0f6bcf	284	#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL
211ea91a	285
211ea91a SR	286	/*-----------------------------------------------------------------------
	287	* External Bus Controller (EBC) Setup
	288	----------------------------------------------------------------------/
	289	/* Memory Bank 0 (NOR-FLASH) initialization */
6d0f6bcf JCPV	290	#define CONFIG_SYS_EBC_PB0AP 0x08033700
6d0f6bcf JCPV	291	#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE \| 0xda000)
211ea91a SR	292
211ea91a SR	293	/* Memory Bank 2 (CPLD) initialization */
6d0f6bcf JCPV	294	#define CONFIG_SYS_EBC_PB2AP 0x9400C800
6d0f6bcf JCPV	295	#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */
211ea91a	296
6d0f6bcf	297	#define CONFIG_SYS_EBC_CFG 0x7FC00000 /* EBC0_CFG */
211ea91a SR	298
	299	/*-----------------------------------------------------------------------
	300	* GPIO Setup
	301	----------------------------------------------------------------------/
6d0f6bcf	302	#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
ecdcbd4f SR	303	{ \
	304	/* GPIO Core 0 */ \
	305	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \
	306	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \
	307	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \
	308	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \
7cfc12a7 SR	309	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \
	310	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \
	311	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \
	312	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \
8be76090 SR	313	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 CS(1)/NFCE(1) IRQ(7) */ \
	314	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 CS(2)/NFCE(2) IRQ(8) */ \
	315	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3) IRQ(9) */ \
ecdcbd4f	316	{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \
7cfc12a7 SR	317	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \
	318	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \
	319	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \
	320	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \
ecdcbd4f SR	321	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \
	322	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \
	323	{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \
	324	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \
	325	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \
	326	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \
	327	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \
	328	{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \
	329	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \
	330	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \
	331	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \
	332	{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \
	333	{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 */ \
8be76090 SR	334	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO29 DMA_EOT1 IRQ(2) */ \
	335	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 DMA_REQ1 IRQ(1) */ \
	336	{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO31 DMA_ACK1 IRQ(0) */ \
ecdcbd4f SR	337	} \
	338	}
	339
6d0f6bcf JCPV	340	#define CONFIG_SYS_GPIO_PCIE_RST 23
	341	#define CONFIG_SYS_GPIO_PCIE_CLKREQ 27
	342	#define CONFIG_SYS_GPIO_PCIE_WAKE 28
211ea91a	343
211ea91a	344	#endif /* __CONFIG_H */