[J-u-boot.git] / include / ns16550.h

/*
 * NS16550 Serial Port
 * originally from linux source (arch/powerpc/boot/ns16550.h)
 *
 * Cleanup and unification
 * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
 *
 * modified slightly to
 * have addresses as offsets from CONFIG_SYS_ISA_BASE
 * added a few more definitions
 * added prototypes for ns16550.c
 * reduced no of com ports to 2
 * modifications (c) Rob Taylor, Flying Pig Systems. 2000.
 *
 * added support for port on 64-bit bus
 * by Richard Danter ([email protected]), (C) 2005 Wind River Systems
 */

/*
 * Note that the following macro magic uses the fact that the compiler
 * will not allocate storage for arrays of size 0
 */

#ifndef __ns16550_h
#define __ns16550_h

#include <linux/types.h>

#ifdef CONFIG_DM_SERIAL
/*
 * For driver model we always use one byte per register, and sort out the
 * differences in the driver
 */
#define CONFIG_SYS_NS16550_REG_SIZE (-1)
#endif

#ifdef CONFIG_NS16550_DYNAMIC
#define UART_REG(x)	unsigned char x
#else
#if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0)
#error "Please define NS16550 registers size."
#elif defined(CONFIG_SYS_NS16550_MEM32) && !defined(CONFIG_DM_SERIAL)
#define UART_REG(x) u32 x
#elif (CONFIG_SYS_NS16550_REG_SIZE > 0)
#define UART_REG(x)						   \
	unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \
	unsigned char x;
#elif (CONFIG_SYS_NS16550_REG_SIZE < 0)
#define UART_REG(x)							\
	unsigned char x;						\
	unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1];
#endif
#endif /* CONFIG_NS16550_DYNAMIC */

enum ns16550_flags {
	NS16550_FLAG_IO		= 1 << 0, /* Use I/O access (else mem-mapped) */
	NS16550_FLAG_ENDIAN	= 1 << 1, /* Use out_le/be_32() */
	NS16550_FLAG_BE		= 1 << 2, /* Big-endian access (else little) */
};

/**
 * struct ns16550_plat - information about a NS16550 port
 *
 * @base:		Base register address
 * @reg_width:		IO accesses size of registers (in bytes, 1 or 4)
 * @reg_shift:		Shift size of registers (0=byte, 1=16bit, 2=32bit...)
 * @reg_offset:		Offset to start of registers (normally 0)
 * @clock:		UART base clock speed in Hz
 * @fcr:		Offset of FCR register (normally UART_FCR_DEFVAL)
 * @flags:		A few flags (enum ns16550_flags)
 * @bdf:		PCI slot/function (pci_dev_t)
 */
struct ns16550_plat {
	unsigned long base;
	int reg_width;
	int reg_shift;
	int reg_offset;
	int clock;
	u32 fcr;
	int flags;
#if defined(CONFIG_PCI) && defined(CONFIG_SPL)
	int bdf;
#endif
};

struct udevice;

struct ns16550 {
	UART_REG(rbr);		/* 0 */
	UART_REG(ier);		/* 1 */
	UART_REG(fcr);		/* 2 */
	UART_REG(lcr);		/* 3 */
	UART_REG(mcr);		/* 4 */
	UART_REG(lsr);		/* 5 */
	UART_REG(msr);		/* 6 */
	UART_REG(spr);		/* 7 */
#ifdef CONFIG_SOC_DA8XX
	UART_REG(reg8);		/* 8 */
	UART_REG(reg9);		/* 9 */
	UART_REG(revid1);	/* A */
	UART_REG(revid2);	/* B */
	UART_REG(pwr_mgmt);	/* C */
	UART_REG(mdr1);		/* D */
#else
	UART_REG(mdr1);		/* 8 */
	UART_REG(reg9);		/* 9 */
	UART_REG(regA);		/* A */
	UART_REG(regB);		/* B */
	UART_REG(regC);		/* C */
	UART_REG(regD);		/* D */
	UART_REG(regE);		/* E */
	UART_REG(uasr);		/* F */
	UART_REG(scr);		/* 10*/
	UART_REG(ssr);		/* 11*/
#endif
#ifdef CONFIG_DM_SERIAL
	struct ns16550_plat *plat;
#endif
};

#define thr rbr
#define iir fcr
#define dll rbr
#define dlm ier

/*
 * These are the definitions for the FIFO Control Register
 */
#define UART_FCR_FIFO_EN	0x01 /* Fifo enable */
#define UART_FCR_CLEAR_RCVR	0x02 /* Clear the RCVR FIFO */
#define UART_FCR_CLEAR_XMIT	0x04 /* Clear the XMIT FIFO */
#define UART_FCR_DMA_SELECT	0x08 /* For DMA applications */
#define UART_FCR_TRIGGER_MASK	0xC0 /* Mask for the FIFO trigger range */
#define UART_FCR_TRIGGER_1	0x00 /* Mask for trigger set at 1 */
#define UART_FCR_TRIGGER_4	0x40 /* Mask for trigger set at 4 */
#define UART_FCR_TRIGGER_8	0x80 /* Mask for trigger set at 8 */
#define UART_FCR_TRIGGER_14	0xC0 /* Mask for trigger set at 14 */

#define UART_FCR_RXSR		0x02 /* Receiver soft reset */
#define UART_FCR_TXSR		0x04 /* Transmitter soft reset */

/* Ingenic JZ47xx specific UART-enable bit. */
#define UART_FCR_UME		0x10

/* Clear & enable FIFOs */
#define UART_FCR_DEFVAL (UART_FCR_FIFO_EN | \
			UART_FCR_RXSR |	\
			UART_FCR_TXSR)

/*
 * These are the definitions for the Modem Control Register
 */
#define UART_MCR_DTR	0x01		/* DTR   */
#define UART_MCR_RTS	0x02		/* RTS   */
#define UART_MCR_OUT1	0x04		/* Out 1 */
#define UART_MCR_OUT2	0x08		/* Out 2 */
#define UART_MCR_LOOP	0x10		/* Enable loopback test mode */
#define UART_MCR_AFE	0x20		/* Enable auto-RTS/CTS */

#define UART_MCR_DMA_EN	0x04
#define UART_MCR_TX_DFR	0x08

/*
 * These are the definitions for the Line Control Register
 *
 * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
 * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
 */
#define UART_LCR_WLS_MSK 0x03		/* character length select mask */
#define UART_LCR_WLS_5	0x00		/* 5 bit character length */
#define UART_LCR_WLS_6	0x01		/* 6 bit character length */
#define UART_LCR_WLS_7	0x02		/* 7 bit character length */
#define UART_LCR_WLS_8	0x03		/* 8 bit character length */
#define UART_LCR_STB	0x04		/* # stop Bits, off=1, on=1.5 or 2) */
#define UART_LCR_PEN	0x08		/* Parity eneble */
#define UART_LCR_EPS	0x10		/* Even Parity Select */
#define UART_LCR_STKP	0x20		/* Stick Parity */
#define UART_LCR_SBRK	0x40		/* Set Break */
#define UART_LCR_BKSE	0x80		/* Bank select enable */
#define UART_LCR_DLAB	0x80		/* Divisor latch access bit */

/*
 * These are the definitions for the Line Status Register
 */
#define UART_LSR_DR	0x01		/* Data ready */
#define UART_LSR_OE	0x02		/* Overrun */
#define UART_LSR_PE	0x04		/* Parity error */
#define UART_LSR_FE	0x08		/* Framing error */
#define UART_LSR_BI	0x10		/* Break */
#define UART_LSR_THRE	0x20		/* Xmit holding register empty */
#define UART_LSR_TEMT	0x40		/* Xmitter empty */
#define UART_LSR_ERR	0x80		/* Error */

#define UART_MSR_DCD	0x80		/* Data Carrier Detect */
#define UART_MSR_RI	0x40		/* Ring Indicator */
#define UART_MSR_DSR	0x20		/* Data Set Ready */
#define UART_MSR_CTS	0x10		/* Clear to Send */
#define UART_MSR_DDCD	0x08		/* Delta DCD */
#define UART_MSR_TERI	0x04		/* Trailing edge ring indicator */
#define UART_MSR_DDSR	0x02		/* Delta DSR */
#define UART_MSR_DCTS	0x01		/* Delta CTS */

/*
 * These are the definitions for the Interrupt Identification Register
 */
#define UART_IIR_NO_INT	0x01	/* No interrupts pending */
#define UART_IIR_ID	0x06	/* Mask for the interrupt ID */

#define UART_IIR_MSI	0x00	/* Modem status interrupt */
#define UART_IIR_THRI	0x02	/* Transmitter holding register empty */
#define UART_IIR_RDI	0x04	/* Receiver data interrupt */
#define UART_IIR_RLSI	0x06	/* Receiver line status interrupt */

/*
 * These are the definitions for the Interrupt Enable Register
 */
#define UART_IER_MSI	0x08	/* Enable Modem status interrupt */
#define UART_IER_RLSI	0x04	/* Enable receiver line status interrupt */
#define UART_IER_THRI	0x02	/* Enable Transmitter holding register int. */
#define UART_IER_RDI	0x01	/* Enable receiver data interrupt */

/* useful defaults for LCR */
#define UART_LCR_8N1	0x03

void ns16550_init(struct ns16550 *com_port, int baud_divisor);
void ns16550_putc(struct ns16550 *com_port, char c);
char ns16550_getc(struct ns16550 *com_port);
int ns16550_tstc(struct ns16550 *com_port);
void ns16550_reinit(struct ns16550 *com_port, int baud_divisor);

/**
 * ns16550_calc_divisor() - calculate the divisor given clock and baud rate
 *
 * Given the UART input clock and required baudrate, calculate the divisor
 * that should be used.
 *
 * @port:	UART port
 * @clock:	UART input clock speed in Hz
 * @baudrate:	Required baud rate
 * Return: baud rate divisor that should be used
 */
int ns16550_calc_divisor(struct ns16550 *port, int clock, int baudrate);

/**
 * ns16550_serial_of_to_plat() - convert DT to platform data
 *
 * Decode a device tree node for an ns16550 device. This includes the
 * register base address and register shift properties. The caller must set
 * up the clock frequency.
 *
 * @dev:	dev to decode platform data for
 * @return:	0 if OK, -EINVAL on error
 */
int ns16550_serial_of_to_plat(struct udevice *dev);

/**
 * ns16550_serial_probe() - probe a serial port
 *
 * This sets up the serial port ready for use, except for the baud rate
 * Return: 0, or -ve on error
 */
int ns16550_serial_probe(struct udevice *dev);

/**
 * struct ns16550_serial_ops - ns16550 serial operations
 *
 * These should be used by the client driver for the driver's 'ops' member
 */
extern const struct dm_serial_ops ns16550_serial_ops;

#endif /* __ns16550_h */
Commit	Line	Data
717b5aad WD	1	/*
717b5aad WD	2	* NS16550 Serial Port
a47a12be	3	* originally from linux source (arch/powerpc/boot/ns16550.h)
200779e3 DZ	4	*
	5	* Cleanup and unification
	6	* (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
	7	*
717b5aad	8	* modified slightly to
6d0f6bcf	9	* have addresses as offsets from CONFIG_SYS_ISA_BASE
717b5aad WD	10	* added a few more definitions
	11	* added prototypes for ns16550.c
	12	* reduced no of com ports to 2
	13	* modifications (c) Rob Taylor, Flying Pig Systems. 2000.
b87dfd28	14	*
f5e0d039 HS	15	* added support for port on 64-bit bus
f5e0d039 HS	16	* by Richard Danter ([email protected]), (C) 2005 Wind River Systems
717b5aad WD	17	*/
717b5aad WD	18
453c0d75 DZ	19	/*
	20	* Note that the following macro magic uses the fact that the compiler
	21	* will not allocate storage for arrays of size 0
	22	*/
	23
d30c7209 SG	24	#ifndef __ns16550_h
	25	#define __ns16550_h
	26
79df1208 DA	27	#include <linux/types.h>
79df1208 DA	28
12e431b2 SG	29	#ifdef CONFIG_DM_SERIAL
	30	/*
	31	* For driver model we always use one byte per register, and sort out the
	32	* differences in the driver
	33	*/
	34	#define CONFIG_SYS_NS16550_REG_SIZE (-1)
	35	#endif
	36
62cbde4c SG	37	#ifdef CONFIG_NS16550_DYNAMIC
	38	#define UART_REG(x) unsigned char x
	39	#else
453c0d75	40	#if !defined(CONFIG_SYS_NS16550_REG_SIZE) \|\| (CONFIG_SYS_NS16550_REG_SIZE == 0)
717b5aad	41	#error "Please define NS16550 registers size."
90914008	42	#elif defined(CONFIG_SYS_NS16550_MEM32) && !defined(CONFIG_DM_SERIAL)
79df1208	43	#define UART_REG(x) u32 x
453c0d75 DZ	44	#elif (CONFIG_SYS_NS16550_REG_SIZE > 0)
	45	#define UART_REG(x) \
	46	unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \
	47	unsigned char x;
	48	#elif (CONFIG_SYS_NS16550_REG_SIZE < 0)
	49	#define UART_REG(x) \
	50	unsigned char x; \
	51	unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1];
717b5aad	52	#endif
62cbde4c SG	53	#endif /* CONFIG_NS16550_DYNAMIC */
	54
	55	enum ns16550_flags {
	56	NS16550_FLAG_IO = 1 << 0, /* Use I/O access (else mem-mapped) */
	57	NS16550_FLAG_ENDIAN = 1 << 1, /* Use out_le/be_32() */
	58	NS16550_FLAG_BE = 1 << 2, /* Big-endian access (else little) */
	59	};
717b5aad	60
12e431b2	61	/**
8a8d24bd	62	* struct ns16550_plat - information about a NS16550 port
12e431b2 SG	63	*
12e431b2 SG	64	* @base: Base register address
62cbde4c	65	* @reg_width: IO accesses size of registers (in bytes, 1 or 4)
12e431b2	66	* @reg_shift: Shift size of registers (0=byte, 1=16bit, 2=32bit...)
62cbde4c	67	* @reg_offset: Offset to start of registers (normally 0)
12e431b2	68	* @clock: UART base clock speed in Hz
62cbde4c SG	69	* @fcr: Offset of FCR register (normally UART_FCR_DEFVAL)
62cbde4c SG	70	* @flags: A few flags (enum ns16550_flags)
4e8de068	71	* @bdf: PCI slot/function (pci_dev_t)
12e431b2	72	*/
8a8d24bd	73	struct ns16550_plat {
167efe01	74	unsigned long base;
4e720779	75	int reg_width;
12e431b2	76	int reg_shift;
59b35ddd	77	int reg_offset;
0af76162	78	int clock;
65f83802	79	u32 fcr;
62cbde4c	80	int flags;
4e8de068 SG	81	#if defined(CONFIG_PCI) && defined(CONFIG_SPL)
	82	int bdf;
	83	#endif
12e431b2 SG	84	};
	85
	86	struct udevice;
	87
d30c7209	88	struct ns16550 {
453c0d75 DZ	89	UART_REG(rbr); /* 0 */
	90	UART_REG(ier); /* 1 */
	91	UART_REG(fcr); /* 2 */
	92	UART_REG(lcr); /* 3 */
	93	UART_REG(mcr); /* 4 */
	94	UART_REG(lsr); /* 5 */
	95	UART_REG(msr); /* 6 */
	96	UART_REG(spr); /* 7 */
99b603e7 MK	97	#ifdef CONFIG_SOC_DA8XX
	98	UART_REG(reg8); /* 8 */
	99	UART_REG(reg9); /* 9 */
	100	UART_REG(revid1); /* A */
	101	UART_REG(revid2); /* B */
	102	UART_REG(pwr_mgmt); /* C */
	103	UART_REG(mdr1); /* D */
	104	#else
453c0d75 DZ	105	UART_REG(mdr1); /* 8 */
	106	UART_REG(reg9); /* 9 */
	107	UART_REG(regA); /* A */
	108	UART_REG(regB); /* B */
	109	UART_REG(regC); /* C */
	110	UART_REG(regD); /* D */
	111	UART_REG(regE); /* E */
	112	UART_REG(uasr); /* F */
	113	UART_REG(scr); /* 10*/
	114	UART_REG(ssr); /* 11*/
99b603e7	115	#endif
12e431b2	116	#ifdef CONFIG_DM_SERIAL
8a8d24bd	117	struct ns16550_plat *plat;
12e431b2	118	#endif
453c0d75 DZ	119	};
453c0d75 DZ	120
717b5aad WD	121	#define thr rbr
	122	#define iir fcr
	123	#define dll rbr
	124	#define dlm ier
	125
200779e3 DZ	126	/*
	127	* These are the definitions for the FIFO Control Register
	128	*/
f8df9d0d	129	#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */
200779e3 DZ	130	#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
	131	#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
	132	#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
	133	#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
	134	#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
	135	#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
	136	#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
	137	#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
	138
	139	#define UART_FCR_RXSR 0x02 /* Receiver soft reset */
	140	#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */
	141
0b060eef MV	142	/* Ingenic JZ47xx specific UART-enable bit. */
	143	#define UART_FCR_UME 0x10
	144
17fa0326 HS	145	/* Clear & enable FIFOs */
	146	#define UART_FCR_DEFVAL (UART_FCR_FIFO_EN \| \
	147	UART_FCR_RXSR \| \
	148	UART_FCR_TXSR)
	149
200779e3 DZ	150	/*
	151	* These are the definitions for the Modem Control Register
	152	*/
	153	#define UART_MCR_DTR 0x01 /* DTR */
	154	#define UART_MCR_RTS 0x02 /* RTS */
	155	#define UART_MCR_OUT1 0x04 /* Out 1 */
	156	#define UART_MCR_OUT2 0x08 /* Out 2 */
	157	#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
d57dee57	158	#define UART_MCR_AFE 0x20 /* Enable auto-RTS/CTS */
200779e3 DZ	159
	160	#define UART_MCR_DMA_EN 0x04
	161	#define UART_MCR_TX_DFR 0x08
	162
	163	/*
	164	* These are the definitions for the Line Control Register
	165	*
	166	* Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
	167	* UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
	168	*/
	169	#define UART_LCR_WLS_MSK 0x03 /* character length select mask */
	170	#define UART_LCR_WLS_5 0x00 /* 5 bit character length */
	171	#define UART_LCR_WLS_6 0x01 /* 6 bit character length */
	172	#define UART_LCR_WLS_7 0x02 /* 7 bit character length */
	173	#define UART_LCR_WLS_8 0x03 /* 8 bit character length */
f8df9d0d	174	#define UART_LCR_STB 0x04 /* # stop Bits, off=1, on=1.5 or 2) */
200779e3 DZ	175	#define UART_LCR_PEN 0x08 /* Parity eneble */
	176	#define UART_LCR_EPS 0x10 /* Even Parity Select */
	177	#define UART_LCR_STKP 0x20 /* Stick Parity */
	178	#define UART_LCR_SBRK 0x40 /* Set Break */
	179	#define UART_LCR_BKSE 0x80 /* Bank select enable */
	180	#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
	181
	182	/*
	183	* These are the definitions for the Line Status Register
	184	*/
	185	#define UART_LSR_DR 0x01 /* Data ready */
	186	#define UART_LSR_OE 0x02 /* Overrun */
	187	#define UART_LSR_PE 0x04 /* Parity error */
	188	#define UART_LSR_FE 0x08 /* Framing error */
	189	#define UART_LSR_BI 0x10 /* Break */
	190	#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
	191	#define UART_LSR_TEMT 0x40 /* Xmitter empty */
	192	#define UART_LSR_ERR 0x80 /* Error */
	193
	194	#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
	195	#define UART_MSR_RI 0x40 /* Ring Indicator */
	196	#define UART_MSR_DSR 0x20 /* Data Set Ready */
	197	#define UART_MSR_CTS 0x10 /* Clear to Send */
	198	#define UART_MSR_DDCD 0x08 /* Delta DCD */
	199	#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
	200	#define UART_MSR_DDSR 0x02 /* Delta DSR */
	201	#define UART_MSR_DCTS 0x01 /* Delta CTS */
	202
	203	/*
	204	* These are the definitions for the Interrupt Identification Register
	205	*/
	206	#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
	207	#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
	208
	209	#define UART_IIR_MSI 0x00 /* Modem status interrupt */
	210	#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
	211	#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
	212	#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
	213
	214	/*
	215	* These are the definitions for the Interrupt Enable Register
	216	*/
	217	#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
	218	#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
	219	#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
	220	#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
	221
717b5aad	222	/* useful defaults for LCR */
200779e3	223	#define UART_LCR_8N1 0x03
717b5aad	224
2d6bf754 SG	225	void ns16550_init(struct ns16550 *com_port, int baud_divisor);
	226	void ns16550_putc(struct ns16550 *com_port, char c);
	227	char ns16550_getc(struct ns16550 *com_port);
	228	int ns16550_tstc(struct ns16550 *com_port);
	229	void ns16550_reinit(struct ns16550 *com_port, int baud_divisor);
fa54eb12 SG	230
	231	/**
	232	* ns16550_calc_divisor() - calculate the divisor given clock and baud rate
	233	*
	234	* Given the UART input clock and required baudrate, calculate the divisor
	235	* that should be used.
	236	*
	237	* @port: UART port
	238	* @clock: UART input clock speed in Hz
	239	* @baudrate: Required baud rate
185f812c	240	* Return: baud rate divisor that should be used
fa54eb12	241	*/
d30c7209	242	int ns16550_calc_divisor(struct ns16550 *port, int clock, int baudrate);
12e431b2 SG	243
12e431b2 SG	244	/**
d1998a9f	245	* ns16550_serial_of_to_plat() - convert DT to platform data
12e431b2 SG	246	*
	247	* Decode a device tree node for an ns16550 device. This includes the
	248	* register base address and register shift properties. The caller must set
	249	* up the clock frequency.
	250	*
	251	* @dev: dev to decode platform data for
	252	* @return: 0 if OK, -EINVAL on error
	253	*/
d1998a9f	254	int ns16550_serial_of_to_plat(struct udevice *dev);
12e431b2 SG	255
	256	/**
	257	* ns16550_serial_probe() - probe a serial port
	258	*
	259	* This sets up the serial port ready for use, except for the baud rate
185f812c	260	* Return: 0, or -ve on error
12e431b2 SG	261	*/
	262	int ns16550_serial_probe(struct udevice *dev);
	263
	264	/**
	265	* struct ns16550_serial_ops - ns16550 serial operations
	266	*
	267	* These should be used by the client driver for the driver's 'ops' member
	268	*/
	269	extern const struct dm_serial_ops ns16550_serial_ops;
d30c7209 SG	270
d30c7209 SG	271	#endif /* __ns16550_h */