[J-u-boot.git] / include / configs / rut.h

/*
 * siemens rut
 * (C) Copyright 2013 Siemens Schweiz AG
 * (C) Heiko Schocher, DENX Software Engineering, [email protected].
 *
 * Based on:
 * U-Boot file:/include/configs/am335x_evm.h
 *
 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_RUT_H
#define __CONFIG_RUT_H

#define CONFIG_SIEMENS_RUT
#define CONFIG_SIEMENS_MACH_TYPE	MACH_TYPE_RUT

#include "siemens-am33x-common.h"

#define RUT_IOCTRL_VAL	0x18b
#define DDR_PLL_FREQ	303

 /* Physical Memory Map */
#define CONFIG_MAX_RAM_BANK_SIZE	(256 << 20) /* 256 MiB */

/* I2C Configuration */
#define CONFIG_SYS_I2C_SPEED		100000

#define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */

#define CONFIG_PHY_NATSEMI

#define CONFIG_FACTORYSET

/* Watchdog */
#define WATCHDOG_TRIGGER_GPIO	14

#ifndef CONFIG_SPL_BUILD

/* Use common default */
#define MTDPARTS_DEFAULT	MTDPARTS_DEFAULT_V1

/* Default env settings */
#define CONFIG_EXTRA_ENV_SETTINGS \
	"hostname=rut\0" \
	"ubi_off=2048\0"\
	"nand_img_size=0x500000\0" \
	"splashpos=m,m\0" \
	"optargs=fixrtc --no-log consoleblank=0 \0" \
	CONFIG_ENV_SETTINGS_V1 \
	CONFIG_ENV_SETTINGS_NAND_V1 \
	"mmc_dev=0\0" \
	"mmc_root=/dev/mmcblk0p2 rw\0" \
	"mmc_root_fs_type=ext4 rootwait\0" \
	"mmc_load_uimage=" \
		"mmc rescan; " \
		"setenv bootfile uImage;" \
		"fatload mmc ${mmc_dev} ${kloadaddr} ${bootfile}\0" \
	"loadbootenv=fatload mmc ${mmc_dev} ${loadaddr} ${bootenv}\0" \
	"importbootenv=echo Importing environment from mmc ...; " \
		"env import -t $loadaddr $filesize\0" \
	"mmc_args=run bootargs_defaults;" \
		"mtdparts default;" \
		"setenv bootargs ${bootargs} " \
		"root=${mmc_root} ${mtdparts}" \
		"rootfstype=${mmc_root_fs_type} ip=${ip_method} " \
		"eth=${ethaddr} " \
		"\0" \
	"mmc_boot=run mmc_args; " \
		"run mmc_load_uimage; " \
		"bootm ${kloadaddr}\0" \
	""

#ifndef CONFIG_RESTORE_FLASH
/* set to negative value for no autoboot */

#define CONFIG_BOOTCOMMAND \
	"if mmc rescan; then " \
		"echo SD/MMC found on device ${mmc_dev};" \
		"if run loadbootenv; then " \
			"echo Loaded environment from ${bootenv};" \
			"run importbootenv;" \
		"fi;" \
		"if test -n $uenvcmd; then " \
			"echo Running uenvcmd ...;" \
			"run uenvcmd;" \
		"fi;" \
		"if run mmc_load_uimage; then " \
			"run mmc_args;" \
			"bootm ${kloadaddr};" \
		"fi;" \
	"fi;" \
	"run nand_boot;" \
	"reset;"

#else

#define CONFIG_BOOTCOMMAND			\
	"setenv autoload no; "			\
	"dhcp; "				\
	"if tftp 80000000 debrick.scr; then "	\
		"source 80000000; "		\
	"fi"
#endif

#endif /* CONFIG_SPL_BUILD */

#ifdef CONFIG_SPL_BUILD
#undef CONFIG_HW_WATCHDOG
#endif

#if defined(CONFIG_VIDEO)
#define CONFIG_VIDEO_DA8XX
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_BMP_LOGO
#define DA8XX_LCD_CNTL_BASE	LCD_CNTL_BASE

#define CONFIG_SPI
#define CONFIG_OMAP3_SPI

#define BOARD_LCD_RESET		115	/* Bank 3 pin 19 */
#define CONFIG_FORMIKE
#define DISPL_PLL_SPREAD_SPECTRUM
#endif

#endif	/* ! __CONFIG_RUT_H */
Commit	Line	Data
c0dcece7 HS	1	/*
	2	* siemens rut
	3	* (C) Copyright 2013 Siemens Schweiz AG
	4	* (C) Heiko Schocher, DENX Software Engineering, [email protected].
	5	*
	6	* Based on:
	7	* U-Boot file:/include/configs/am335x_evm.h
	8	*
	9	* Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
	10	*
	11	* SPDX-License-Identifier: GPL-2.0+
	12	*/
	13
	14	#ifndef __CONFIG_RUT_H
	15	#define __CONFIG_RUT_H
	16
	17	#define CONFIG_SIEMENS_RUT
c0dcece7 HS	18	#define CONFIG_SIEMENS_MACH_TYPE MACH_TYPE_RUT
	19
	20	#include "siemens-am33x-common.h"
	21
c0dcece7 HS	22	#define RUT_IOCTRL_VAL 0x18b
	23	#define DDR_PLL_FREQ 303
	24
	25	/* Physical Memory Map */
	26	#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MiB */
	27
	28	/* I2C Configuration */
	29	#define CONFIG_SYS_I2C_SPEED 100000
	30
	31	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	32	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	33	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
	34	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
	35
c0dcece7 HS	36	#define CONFIG_PHY_NATSEMI
	37
	38	#define CONFIG_FACTORYSET
	39
c0dcece7 HS	40	/* Watchdog */
	41	#define WATCHDOG_TRIGGER_GPIO 14
	42
	43	#ifndef CONFIG_SPL_BUILD
	44
61159b76 HS	45	/* Use common default */
	46	#define MTDPARTS_DEFAULT MTDPARTS_DEFAULT_V1
	47
c0dcece7 HS	48	/* Default env settings */
	49	#define CONFIG_EXTRA_ENV_SETTINGS \
	50	"hostname=rut\0" \
6b3943f1	51	"ubi_off=2048\0"\
56eb3da4 SE	52	"nand_img_size=0x500000\0" \
56eb3da4 SE	53	"splashpos=m,m\0" \
c0dcece7	54	"optargs=fixrtc --no-log consoleblank=0 \0" \
61159b76 HS	55	CONFIG_ENV_SETTINGS_V1 \
61159b76 HS	56	CONFIG_ENV_SETTINGS_NAND_V1 \
c0dcece7 HS	57	"mmc_dev=0\0" \
	58	"mmc_root=/dev/mmcblk0p2 rw\0" \
	59	"mmc_root_fs_type=ext4 rootwait\0" \
	60	"mmc_load_uimage=" \
	61	"mmc rescan; " \
	62	"setenv bootfile uImage;" \
	63	"fatload mmc ${mmc_dev} ${kloadaddr} ${bootfile}\0" \
	64	"loadbootenv=fatload mmc ${mmc_dev} ${loadaddr} ${bootenv}\0" \
	65	"importbootenv=echo Importing environment from mmc ...; " \
	66	"env import -t $loadaddr $filesize\0" \
	67	"mmc_args=run bootargs_defaults;" \
	68	"mtdparts default;" \
	69	"setenv bootargs ${bootargs} " \
	70	"root=${mmc_root} ${mtdparts}" \
	71	"rootfstype=${mmc_root_fs_type} ip=${ip_method} " \
	72	"eth=${ethaddr} " \
	73	"\0" \
	74	"mmc_boot=run mmc_args; " \
	75	"run mmc_load_uimage; " \
	76	"bootm ${kloadaddr}\0" \
	77	""
	78
	79	#ifndef CONFIG_RESTORE_FLASH
	80	/* set to negative value for no autoboot */
c0dcece7 HS	81
	82	#define CONFIG_BOOTCOMMAND \
	83	"if mmc rescan; then " \
	84	"echo SD/MMC found on device ${mmc_dev};" \
	85	"if run loadbootenv; then " \
	86	"echo Loaded environment from ${bootenv};" \
	87	"run importbootenv;" \
	88	"fi;" \
	89	"if test -n $uenvcmd; then " \
	90	"echo Running uenvcmd ...;" \
	91	"run uenvcmd;" \
	92	"fi;" \
	93	"if run mmc_load_uimage; then " \
	94	"run mmc_args;" \
	95	"bootm ${kloadaddr};" \
	96	"fi;" \
	97	"fi;" \
	98	"run nand_boot;" \
56eb3da4	99	"reset;"
c0dcece7 HS	100
c0dcece7 HS	101	#else
c0dcece7 HS	102
	103	#define CONFIG_BOOTCOMMAND \
	104	"setenv autoload no; " \
	105	"dhcp; " \
	106	"if tftp 80000000 debrick.scr; then " \
	107	"source 80000000; " \
	108	"fi"
	109	#endif
	110
	111	#endif /* CONFIG_SPL_BUILD */
	112
	113	#ifdef CONFIG_SPL_BUILD
	114	#undef CONFIG_HW_WATCHDOG
	115	#endif
	116
c0dcece7 HS	117	#if defined(CONFIG_VIDEO)
c0dcece7 HS	118	#define CONFIG_VIDEO_DA8XX
c0dcece7 HS	119	#define CONFIG_SPLASH_SCREEN
	120	#define CONFIG_SPLASH_SCREEN_ALIGN
	121	#define CONFIG_VIDEO_LOGO
	122	#define CONFIG_VIDEO_BMP_RLE8
	123	#define CONFIG_VIDEO_BMP_LOGO
c0dcece7 HS	124	#define DA8XX_LCD_CNTL_BASE LCD_CNTL_BASE
	125
	126	#define CONFIG_SPI
	127	#define CONFIG_OMAP3_SPI
	128
	129	#define BOARD_LCD_RESET 115 /* Bank 3 pin 19 */
c0dcece7	130	#define CONFIG_FORMIKE
56eb3da4	131	#define DISPL_PLL_SPREAD_SPECTRUM
c0dcece7 HS	132	#endif
	133
	134	#endif /* ! __CONFIG_RUT_H */