[J-u-boot.git] / include / ns16550.h

/*
 * NS16550 Serial Port
 * originally from linux source (arch/powerpc/boot/ns16550.h)
 *
 * Cleanup and unification
 * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
 *
 * modified slightly to
 * have addresses as offsets from CONFIG_SYS_ISA_BASE
 * added a few more definitions
 * added prototypes for ns16550.c
 * reduced no of com ports to 2
 * modifications (c) Rob Taylor, Flying Pig Systems. 2000.
 *
 * added support for port on 64-bit bus
 * by Richard Danter ([email protected]), (C) 2005 Wind River Systems
 */

/*
 * Note that the following macro magic uses the fact that the compiler
 * will not allocate storage for arrays of size 0
 */

#include <linux/types.h>

#if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0)
#error "Please define NS16550 registers size."
#elif defined(CONFIG_SYS_NS16550_MEM32)
#define UART_REG(x) u32 x
#elif (CONFIG_SYS_NS16550_REG_SIZE > 0)
#define UART_REG(x)						   \
	unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \
	unsigned char x;
#elif (CONFIG_SYS_NS16550_REG_SIZE < 0)
#define UART_REG(x)							\
	unsigned char x;						\
	unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1];
#endif

struct NS16550 {
	UART_REG(rbr);		/* 0 */
	UART_REG(ier);		/* 1 */
	UART_REG(fcr);		/* 2 */
	UART_REG(lcr);		/* 3 */
	UART_REG(mcr);		/* 4 */
	UART_REG(lsr);		/* 5 */
	UART_REG(msr);		/* 6 */
	UART_REG(spr);		/* 7 */
#ifdef CONFIG_SOC_DA8XX
	UART_REG(reg8);		/* 8 */
	UART_REG(reg9);		/* 9 */
	UART_REG(revid1);	/* A */
	UART_REG(revid2);	/* B */
	UART_REG(pwr_mgmt);	/* C */
	UART_REG(mdr1);		/* D */
#else
	UART_REG(mdr1);		/* 8 */
	UART_REG(reg9);		/* 9 */
	UART_REG(regA);		/* A */
	UART_REG(regB);		/* B */
	UART_REG(regC);		/* C */
	UART_REG(regD);		/* D */
	UART_REG(regE);		/* E */
	UART_REG(uasr);		/* F */
	UART_REG(scr);		/* 10*/
	UART_REG(ssr);		/* 11*/
	UART_REG(reg12);	/* 12*/
	UART_REG(osc_12m_sel);	/* 13*/
#endif
};

#define thr rbr
#define iir fcr
#define dll rbr
#define dlm ier

typedef struct NS16550 *NS16550_t;

/*
 * These are the definitions for the FIFO Control Register
 */
#define UART_FCR_FIFO_EN	0x01 /* Fifo enable */
#define UART_FCR_CLEAR_RCVR	0x02 /* Clear the RCVR FIFO */
#define UART_FCR_CLEAR_XMIT	0x04 /* Clear the XMIT FIFO */
#define UART_FCR_DMA_SELECT	0x08 /* For DMA applications */
#define UART_FCR_TRIGGER_MASK	0xC0 /* Mask for the FIFO trigger range */
#define UART_FCR_TRIGGER_1	0x00 /* Mask for trigger set at 1 */
#define UART_FCR_TRIGGER_4	0x40 /* Mask for trigger set at 4 */
#define UART_FCR_TRIGGER_8	0x80 /* Mask for trigger set at 8 */
#define UART_FCR_TRIGGER_14	0xC0 /* Mask for trigger set at 14 */

#define UART_FCR_RXSR		0x02 /* Receiver soft reset */
#define UART_FCR_TXSR		0x04 /* Transmitter soft reset */

/*
 * These are the definitions for the Modem Control Register
 */
#define UART_MCR_DTR	0x01		/* DTR   */
#define UART_MCR_RTS	0x02		/* RTS   */
#define UART_MCR_OUT1	0x04		/* Out 1 */
#define UART_MCR_OUT2	0x08		/* Out 2 */
#define UART_MCR_LOOP	0x10		/* Enable loopback test mode */

#define UART_MCR_DMA_EN	0x04
#define UART_MCR_TX_DFR	0x08

/*
 * These are the definitions for the Line Control Register
 *
 * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
 * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
 */
#define UART_LCR_WLS_MSK 0x03		/* character length select mask */
#define UART_LCR_WLS_5	0x00		/* 5 bit character length */
#define UART_LCR_WLS_6	0x01		/* 6 bit character length */
#define UART_LCR_WLS_7	0x02		/* 7 bit character length */
#define UART_LCR_WLS_8	0x03		/* 8 bit character length */
#define UART_LCR_STB	0x04		/* # stop Bits, off=1, on=1.5 or 2) */
#define UART_LCR_PEN	0x08		/* Parity eneble */
#define UART_LCR_EPS	0x10		/* Even Parity Select */
#define UART_LCR_STKP	0x20		/* Stick Parity */
#define UART_LCR_SBRK	0x40		/* Set Break */
#define UART_LCR_BKSE	0x80		/* Bank select enable */
#define UART_LCR_DLAB	0x80		/* Divisor latch access bit */

/*
 * These are the definitions for the Line Status Register
 */
#define UART_LSR_DR	0x01		/* Data ready */
#define UART_LSR_OE	0x02		/* Overrun */
#define UART_LSR_PE	0x04		/* Parity error */
#define UART_LSR_FE	0x08		/* Framing error */
#define UART_LSR_BI	0x10		/* Break */
#define UART_LSR_THRE	0x20		/* Xmit holding register empty */
#define UART_LSR_TEMT	0x40		/* Xmitter empty */
#define UART_LSR_ERR	0x80		/* Error */

#define UART_MSR_DCD	0x80		/* Data Carrier Detect */
#define UART_MSR_RI	0x40		/* Ring Indicator */
#define UART_MSR_DSR	0x20		/* Data Set Ready */
#define UART_MSR_CTS	0x10		/* Clear to Send */
#define UART_MSR_DDCD	0x08		/* Delta DCD */
#define UART_MSR_TERI	0x04		/* Trailing edge ring indicator */
#define UART_MSR_DDSR	0x02		/* Delta DSR */
#define UART_MSR_DCTS	0x01		/* Delta CTS */

/*
 * These are the definitions for the Interrupt Identification Register
 */
#define UART_IIR_NO_INT	0x01	/* No interrupts pending */
#define UART_IIR_ID	0x06	/* Mask for the interrupt ID */

#define UART_IIR_MSI	0x00	/* Modem status interrupt */
#define UART_IIR_THRI	0x02	/* Transmitter holding register empty */
#define UART_IIR_RDI	0x04	/* Receiver data interrupt */
#define UART_IIR_RLSI	0x06	/* Receiver line status interrupt */

/*
 * These are the definitions for the Interrupt Enable Register
 */
#define UART_IER_MSI	0x08	/* Enable Modem status interrupt */
#define UART_IER_RLSI	0x04	/* Enable receiver line status interrupt */
#define UART_IER_THRI	0x02	/* Enable Transmitter holding register int. */
#define UART_IER_RDI	0x01	/* Enable receiver data interrupt */


#ifdef CONFIG_OMAP1510
#define OSC_12M_SEL	0x01	/* selects 6.5 * current clk div */
#endif

/* useful defaults for LCR */
#define UART_LCR_8N1	0x03

void NS16550_init(NS16550_t com_port, int baud_divisor);
void NS16550_putc(NS16550_t com_port, char c);
char NS16550_getc(NS16550_t com_port);
int NS16550_tstc(NS16550_t com_port);
void NS16550_reinit(NS16550_t com_port, int baud_divisor);
Commit	Line	Data
717b5aad WD	1	/*
717b5aad WD	2	* NS16550 Serial Port
a47a12be	3	* originally from linux source (arch/powerpc/boot/ns16550.h)
200779e3 DZ	4	*
	5	* Cleanup and unification
	6	* (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
	7	*
717b5aad	8	* modified slightly to
6d0f6bcf	9	* have addresses as offsets from CONFIG_SYS_ISA_BASE
717b5aad WD	10	* added a few more definitions
	11	* added prototypes for ns16550.c
	12	* reduced no of com ports to 2
	13	* modifications (c) Rob Taylor, Flying Pig Systems. 2000.
b87dfd28	14	*
f5e0d039 HS	15	* added support for port on 64-bit bus
f5e0d039 HS	16	* by Richard Danter ([email protected]), (C) 2005 Wind River Systems
717b5aad WD	17	*/
717b5aad WD	18
453c0d75 DZ	19	/*
	20	* Note that the following macro magic uses the fact that the compiler
	21	* will not allocate storage for arrays of size 0
	22	*/
	23
79df1208 DA	24	#include <linux/types.h>
79df1208 DA	25
453c0d75	26	#if !defined(CONFIG_SYS_NS16550_REG_SIZE) \|\| (CONFIG_SYS_NS16550_REG_SIZE == 0)
717b5aad	27	#error "Please define NS16550 registers size."
79df1208 DA	28	#elif defined(CONFIG_SYS_NS16550_MEM32)
79df1208 DA	29	#define UART_REG(x) u32 x
453c0d75 DZ	30	#elif (CONFIG_SYS_NS16550_REG_SIZE > 0)
	31	#define UART_REG(x) \
	32	unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \
	33	unsigned char x;
	34	#elif (CONFIG_SYS_NS16550_REG_SIZE < 0)
	35	#define UART_REG(x) \
	36	unsigned char x; \
	37	unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1];
717b5aad WD	38	#endif
717b5aad WD	39
453c0d75 DZ	40	struct NS16550 {
	41	UART_REG(rbr); /* 0 */
	42	UART_REG(ier); /* 1 */
	43	UART_REG(fcr); /* 2 */
	44	UART_REG(lcr); /* 3 */
	45	UART_REG(mcr); /* 4 */
	46	UART_REG(lsr); /* 5 */
	47	UART_REG(msr); /* 6 */
	48	UART_REG(spr); /* 7 */
99b603e7 MK	49	#ifdef CONFIG_SOC_DA8XX
	50	UART_REG(reg8); /* 8 */
	51	UART_REG(reg9); /* 9 */
	52	UART_REG(revid1); /* A */
	53	UART_REG(revid2); /* B */
	54	UART_REG(pwr_mgmt); /* C */
	55	UART_REG(mdr1); /* D */
	56	#else
453c0d75 DZ	57	UART_REG(mdr1); /* 8 */
	58	UART_REG(reg9); /* 9 */
	59	UART_REG(regA); /* A */
	60	UART_REG(regB); /* B */
	61	UART_REG(regC); /* C */
	62	UART_REG(regD); /* D */
	63	UART_REG(regE); /* E */
	64	UART_REG(uasr); /* F */
	65	UART_REG(scr); /* 10*/
	66	UART_REG(ssr); /* 11*/
	67	UART_REG(reg12); /* 12*/
	68	UART_REG(osc_12m_sel); /* 13*/
99b603e7	69	#endif
453c0d75 DZ	70	};
453c0d75 DZ	71
717b5aad WD	72	#define thr rbr
	73	#define iir fcr
	74	#define dll rbr
	75	#define dlm ier
	76
f8df9d0d	77	typedef struct NS16550 *NS16550_t;
717b5aad	78
200779e3 DZ	79	/*
	80	* These are the definitions for the FIFO Control Register
	81	*/
f8df9d0d	82	#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */
200779e3 DZ	83	#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
	84	#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
	85	#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
	86	#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
	87	#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
	88	#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
	89	#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
	90	#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
	91
	92	#define UART_FCR_RXSR 0x02 /* Receiver soft reset */
	93	#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */
	94
	95	/*
	96	* These are the definitions for the Modem Control Register
	97	*/
	98	#define UART_MCR_DTR 0x01 /* DTR */
	99	#define UART_MCR_RTS 0x02 /* RTS */
	100	#define UART_MCR_OUT1 0x04 /* Out 1 */
	101	#define UART_MCR_OUT2 0x08 /* Out 2 */
	102	#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
	103
	104	#define UART_MCR_DMA_EN 0x04
	105	#define UART_MCR_TX_DFR 0x08
	106
	107	/*
	108	* These are the definitions for the Line Control Register
	109	*
	110	* Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
	111	* UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
	112	*/
	113	#define UART_LCR_WLS_MSK 0x03 /* character length select mask */
	114	#define UART_LCR_WLS_5 0x00 /* 5 bit character length */
	115	#define UART_LCR_WLS_6 0x01 /* 6 bit character length */
	116	#define UART_LCR_WLS_7 0x02 /* 7 bit character length */
	117	#define UART_LCR_WLS_8 0x03 /* 8 bit character length */
f8df9d0d	118	#define UART_LCR_STB 0x04 /* # stop Bits, off=1, on=1.5 or 2) */
200779e3 DZ	119	#define UART_LCR_PEN 0x08 /* Parity eneble */
	120	#define UART_LCR_EPS 0x10 /* Even Parity Select */
	121	#define UART_LCR_STKP 0x20 /* Stick Parity */
	122	#define UART_LCR_SBRK 0x40 /* Set Break */
	123	#define UART_LCR_BKSE 0x80 /* Bank select enable */
	124	#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
	125
	126	/*
	127	* These are the definitions for the Line Status Register
	128	*/
	129	#define UART_LSR_DR 0x01 /* Data ready */
	130	#define UART_LSR_OE 0x02 /* Overrun */
	131	#define UART_LSR_PE 0x04 /* Parity error */
	132	#define UART_LSR_FE 0x08 /* Framing error */
	133	#define UART_LSR_BI 0x10 /* Break */
	134	#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
	135	#define UART_LSR_TEMT 0x40 /* Xmitter empty */
	136	#define UART_LSR_ERR 0x80 /* Error */
	137
	138	#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
	139	#define UART_MSR_RI 0x40 /* Ring Indicator */
	140	#define UART_MSR_DSR 0x20 /* Data Set Ready */
	141	#define UART_MSR_CTS 0x10 /* Clear to Send */
	142	#define UART_MSR_DDCD 0x08 /* Delta DCD */
	143	#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
	144	#define UART_MSR_DDSR 0x02 /* Delta DSR */
	145	#define UART_MSR_DCTS 0x01 /* Delta CTS */
	146
	147	/*
	148	* These are the definitions for the Interrupt Identification Register
	149	*/
	150	#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
	151	#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
	152
	153	#define UART_IIR_MSI 0x00 /* Modem status interrupt */
	154	#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
	155	#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
	156	#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
	157
	158	/*
	159	* These are the definitions for the Interrupt Enable Register
	160	*/
	161	#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
	162	#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
	163	#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
	164	#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
	165
7b5611cd	166
2e5983d2	167	#ifdef CONFIG_OMAP1510
200779e3	168	#define OSC_12M_SEL 0x01 /* selects 6.5 * current clk div */
2e5983d2 WD	169	#endif
2e5983d2 WD	170
717b5aad	171	/* useful defaults for LCR */
200779e3	172	#define UART_LCR_8N1 0x03
717b5aad	173
f8df9d0d SG	174	void NS16550_init(NS16550_t com_port, int baud_divisor);
	175	void NS16550_putc(NS16550_t com_port, char c);
	176	char NS16550_getc(NS16550_t com_port);
	177	int NS16550_tstc(NS16550_t com_port);
	178	void NS16550_reinit(NS16550_t com_port, int baud_divisor);