[J-u-boot.git] / include / configs / am335x_shc.h

/*
 * (C) Copyright 2016
 * Heiko Schocher, DENX Software Engineering, [email protected].
 *
 * Based on:
 * am335x_evm.h
 *
 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_AM335X_SHC_H
#define __CONFIG_AM335X_SHC_H

#include <configs/ti_am335x_common.h>

/* settings we don;t want on this board */
#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#undef CONFIG_CMD_EXT4
#undef CONFIG_CMD_EXT4_WRITE
#undef CONFIG_CMD_MMC_SPI
#undef CONFIG_CMD_SPI

#define CONFIG_CMD_CACHE

#ifndef CONFIG_SPL_BUILD
# define CONFIG_TIMESTAMP
# define CONFIG_LZO
#endif

#define CONFIG_SYS_BOOTM_LEN		(16 << 20)

#define MACH_TYPE_BOSCH_SHC_B		9001
#define MACH_TYPE_BOSCH_SHC_B2		9002
#define MACH_TYPE_BOSCH_SHC_C		9003
#define MACH_TYPE_BOSCH_SHC_C2		9004
#define MACH_TYPE_BOSCH_SHC_C3		9005
#define MACH_TYPE_BOSCH_SHC		9006
#ifdef CONFIG_B_SAMPLE
# define CONFIG_MACH_TYPE		MACH_TYPE_BOSCH_SHC_B
#elif defined CONFIG_B2_SAMPLE
# define CONFIG_MACH_TYPE		MACH_TYPE_BOSCH_SHC_B2
#elif defined CONFIG_C_SAMPLE
# define CONFIG_MACH_TYPE		MACH_TYPE_BOSCH_SHC_C
#elif defined CONFIG_C2_SAMPLE
# define CONFIG_MACH_TYPE		MACH_TYPE_BOSCH_SHC_C2
#elif defined CONFIG_C3_SAMPLE
# define CONFIG_MACH_TYPE		MACH_TYPE_BOSCH_SHC_C3
#elif defined CONFIG_SERIES
# define CONFIG_MACH_TYPE		MACH_TYPE_BOSCH_SHC
#endif /* #ifdef CONFIG_B_SAMPLE */
/* Clock Defines */
#define V_OSCK				24000000  /* Clock output from T2 */
#define V_SCLK				(V_OSCK)

#define CONFIG_ENV_IS_IN_MMC		1

/*
 * in case of SD Card or Network boot we want to have a possibility to
 * debrick the shc, therefore do not read environment from eMMC
 */
#if defined(CONFIG_SHC_SDBOOT) || defined(CONFIG_SHC_NETBOOT)
#define CONFIG_SYS_MMC_ENV_DEV		0
#else
#define CONFIG_SYS_MMC_ENV_DEV		1
#endif

/*
 * Info when using boot partitions: As environment resides within first
 * 128 kB, MLO must start at 128 kB == 0x20000
 * ENV at MMC Boot0 Partition - 0/Undefined=user, 1=boot0, 2=boot1,
 * 4..7=general0..3
 */
#define CONFIG_ENV_SIZE				0x1000 /* 4 KB */
#define CONFIG_ENV_OFFSET			0x7000 /* 28 kB */

#define CONFIG_HSMMC2_8BIT

#define CONFIG_ENV_OFFSET_REDUND    0x9000 /* 36 kB */
#define CONFIG_ENV_SIZE_REDUND      CONFIG_ENV_SIZE

/* Enhance our eMMC support / experience. */
#define CONFIG_CMD_GPT
#ifndef CONFIG_SHC_ICT
/*
 * In builds other than ICT, reset to retry after timeout
 * Define a timeout after which a stopped bootloader continues autoboot
 * (only works with CONFIG_RESET_TO_RETRY)
 */
# define CONFIG_BOOT_RETRY_TIME 30
# define CONFIG_RESET_TO_RETRY
#endif

#define CONFIG_ENV_VARS_UBOOT_CONFIG
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

#ifndef CONFIG_SPL_BUILD
#define CONFIG_EXTRA_ENV_SETTINGS \
	"loadaddr=0x80200000\0" \
	"kloadaddr=0x84000000\0" \
	"fdtaddr=0x85000000\0" \
	"fdt_high=0xffffffff\0" \
	"rdaddr=0x81000000\0" \
	"bootfile=uImage\0" \
	"fdtfile=am335x-shc.dtb\0" \
	"verify=no\0" \
	"serverip=10.55.152.184\0" \
	"rootpath=/srv/nfs/shc-rootfs\0" \
	"console=ttyO0,115200n8\0" \
	"optargs=quiet\0" \
	"mmcdev=1\0" \
	"harakiri=0\0" \
	"mmcpart=2\0" \
	"active_root=root1\0" \
	"inactive_root=root2\0" \
	"mmcrootfstype=ext4 rootwait\0" \
	"nfsopts=nolock\0" \
	"static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
		"::off\0" \
	"ip_method=none\0" \
	"bootargs_defaults=setenv bootargs " \
		"console=${console} " \
		"${optargs}\0" \
	"mmcargs=run bootargs_defaults;" \
		"setenv bootargs ${bootargs} " \
		"root=${mmcroot} " \
		"rootfstype=${mmcrootfstype} ip=${ip_method}\0" \
	"netargs=setenv bootargs console=${console} " \
		"${optargs} " \
		"root=/dev/nfs " \
		"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
		"ip=dhcp\0" \
	"bootenv=uEnv.txt\0" \
	"loadbootenv=if fatload mmc ${mmcdev} ${loadaddr} ${bootenv}; then " \
			"echo Loaded environment from ${bootenv}; " \
			"run importbootenv; " \
		"fi;\0" \
	"importbootenv=echo Importing environment variables from uEnv.txt ...; " \
		"env import -t $loadaddr $filesize\0" \
	"loaduimagefat=fatload mmc ${mmcdev} ${kloadaddr} ${bootfile}\0" \
	"loaduimage=ext2load mmc ${mmcdev}:${mmcpart} ${kloadaddr} /boot/${bootfile}\0" \
	"loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdtaddr} /boot/${fdtfile}\0" \
	"netloaduimage=tftp ${loadaddr} ${bootfile}\0" \
	"netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
	"mmcboot=echo Booting Linux from ${mmcdevice} ...; " \
		"run mmcargs; " \
		"if run loadfdt; then " \
			"echo device tree detected; " \
			"bootm ${kloadaddr} - ${fdtaddr}; " \
		"else " \
			"bootm ${kloadaddr}; " \
		"fi; \0" \
	"netboot=echo Booting from network ...; " \
		"setenv autoload no; " \
		"dhcp; " \
		"run netloaduimage; " \
		"run netargs; " \
		"echo NFS path: ${serverip}:${rootpath};" \
		"if run netloadfdt; then " \
			"echo device tree detected; " \
			"bootm ${loadaddr} - ${fdtaddr}; " \
		"else " \
			"bootm ${loadaddr}; " \
		"fi; \0" \
	"emmc_erase=if test ${harakiri} = 1 ; then echo erase emmc ...; setenv mmcdev 1; mmc erase 0 200; reset; fi; \0" \
	"mmcpart_gp=mmcpart gp 1 40; \0" \
	"mmcpart_enhance=mmcpart enhance 0 64; \0" \
	"mmcpart_rel_write=mmcpart rel_write 1f; \0" \
	"mmcpart_commit=mmcpart commit 1; \0" \
	"mmc_hw_part=run mmcpart_gp; run mmcpart_enhance; run mmcpart_rel_write; run mmcpart_commit; \0" \
	"led_success=gpio set 22; \0" \
	"fusecmd=mmc dev 1; if mmcpart iscommitted; then echo HW Partitioning already committed; mmcpart list; else run mmc_hw_part; fi; run led_success; \0" \
	"uenv_exec=if test -n $uenvcmd; then " \
			"echo Running uenvcmd ...; " \
			"run uenvcmd; " \
		"fi;\0" \
	"sd_setup=echo SD/MMC-Card detected on device 0; " \
		"setenv mmcdevice SD; " \
		"setenv mmcdev 0; " \
		"setenv mmcpart 2; " \
		"setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0" \
	"emmc_setup=echo eMMC detected on device 1; " \
		"setenv mmcdevice eMMC; " \
		"setenv mmcdev 1; " \
		"run emmc_erase; " \
		"if test ${active_root} = root2; then " \
			"echo Active root is partition 6 (root2); " \
			"setenv mmcpart 6; " \
		"else " \
			"echo Active root is partition 5 (root1); " \
			"setenv mmcpart 5; " \
		"fi; " \
		"setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0"
#endif /* #ifndef CONFIG_SPL_BUILD */

#if defined CONFIG_SHC_NETBOOT
/* Network Boot */
# define CONFIG_BOOTCOMMAND \
	"run fusecmd; " \
	"if run netboot; then " \
		"echo Booting from network; " \
	"else " \
		"echo ERROR: Cannot boot from network!; " \
		"panic; " \
	"fi; "

#elif defined CONFIG_SHC_SDBOOT /* !defined CONFIG_SHC_NETBOOT */
/* SD-Card Boot */
# define CONFIG_BOOTCOMMAND \
	"if mmc dev 0; mmc rescan; then " \
		"run sd_setup; " \
	"else " \
		"echo ERROR: SD/MMC-Card not detected!; " \
		"panic; " \
	"fi; " \
	"if run loaduimage; then " \
		"echo Bootable SD/MMC-Card inserted, booting from it!; " \
		"run mmcboot; " \
	"else " \
		"echo ERROR: Unable to load uImage from SD/MMC-Card!; " \
		"panic; " \
	"fi; "

#elif defined CONFIG_SHC_ICT
/* ICT adapter boots only u-boot and does HW partitioning */
# define CONFIG_BOOTCOMMAND \
	"if mmc dev 0; mmc rescan; then " \
		"run sd_setup; " \
	"else " \
		"echo ERROR: SD/MMC-Card not detected!; " \
		"panic; " \
	"fi; " \
	"run fusecmd; "

#else /* !defined CONFIG_SHC_NETBOOT, !defined CONFIG_SHC_SDBOOT */
/* Regular Boot from internal eMMC */
# define CONFIG_BOOTCOMMAND \
	"if mmc dev 1; mmc rescan; then " \
		"run emmc_setup; " \
	"else " \
		"echo ERROR: eMMC device not detected!; " \
		"panic; " \
	"fi; " \
	"if run loaduimage; then " \
		"run mmcboot; " \
	"else " \
		"echo ERROR Unable to load uImage from eMMC!; " \
		"echo Performing Rollback!; " \
		"setenv _active_ ${active_root}; " \
		"setenv _inactive_ ${inactive_root}; " \
		"setenv active_root ${_inactive_}; " \
		"setenv inactive_root ${_active_}; " \
		"saveenv; " \
		"reset; " \
	"fi; "

#endif /* Regular Boot */

/* NS16550 Configuration */
#define CONFIG_SYS_NS16550_COM1		0x44e09000	/* UART0 */
#define CONFIG_SYS_NS16550_COM2		0x48022000	/* UART1 */
#define CONFIG_SYS_NS16550_COM3		0x48024000	/* UART2 */
#define CONFIG_SYS_NS16550_COM4		0x481a6000	/* UART3 */
#define CONFIG_SYS_NS16550_COM5		0x481a8000	/* UART4 */
#define CONFIG_SYS_NS16550_COM6		0x481aa000	/* UART5 */
#define CONFIG_BAUDRATE			115200
#define CONFIG_CONS_INDEX               1

/* PMIC support */
#define CONFIG_POWER_TPS65217

/* SPL */

#define CONFIG_SPL_LDSCRIPT		"arch/arm/mach-omap2/am33xx/u-boot-spl.lds"

#ifndef CONFIG_SPL_USBETH_SUPPORT
#define CONFIG_FASTBOOT_FLASH_MMC_DEV   1
#endif

/*
 * Disable MMC DM for SPL build and can be re-enabled after adding
 * DM support in SPL
 */
#ifdef CONFIG_SPL_BUILD
#undef CONFIG_DM_MMC
#undef CONFIG_TIMER
#endif

#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_DRIVER_TI_CPSW
#define CONFIG_MII
#define CONFIG_BOOTP_DEFAULT
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_NET_RETRY_COUNT         10
#define CONFIG_NET_MULTI
#define CONFIG_PHY_GIGE
#define CONFIG_PHYLIB
#define CONFIG_PHY_ADDR			0
#define CONFIG_PHY_SMSC

/* I2C configuration */
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* Main EEPROM */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
#define CONFIG_SYS_I2C_SPEED		400000
#define CONFIG_SYS_I2C_SLAVE		1

#define CONFIG_SHOW_BOOT_PROGRESS

#if defined CONFIG_SHC_NETBOOT
#ifdef CONFIG_SPL_BUILD
#define CONFIG_ENV_IS_NOWHERE
#undef CONFIG_ENV_IS_IN_MMC
#endif
#endif
#endif	/* ! __CONFIG_AM335X_SHC_H */
Commit	Line	Data
d8ccbe93 HS	1	/*
	2	* (C) Copyright 2016
	3	* Heiko Schocher, DENX Software Engineering, [email protected].
	4	*
	5	* Based on:
	6	* am335x_evm.h
	7	*
	8	* Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
	9	*
	10	* SPDX-License-Identifier: GPL-2.0+
	11	*/
	12
	13	#ifndef __CONFIG_AM335X_SHC_H
	14	#define __CONFIG_AM335X_SHC_H
	15
	16	#include <configs/ti_am335x_common.h>
	17
	18	/* settings we don;t want on this board */
	19	#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
	20	#undef CONFIG_CMD_EXT4
	21	#undef CONFIG_CMD_EXT4_WRITE
	22	#undef CONFIG_CMD_MMC_SPI
	23	#undef CONFIG_CMD_SPI
d8ccbe93 HS	24
	25	#define CONFIG_CMD_CACHE
	26
	27	#ifndef CONFIG_SPL_BUILD
	28	# define CONFIG_TIMESTAMP
	29	# define CONFIG_LZO
	30	#endif
	31
	32	#define CONFIG_SYS_BOOTM_LEN (16 << 20)
	33
	34	#define MACH_TYPE_BOSCH_SHC_B 9001
	35	#define MACH_TYPE_BOSCH_SHC_B2 9002
	36	#define MACH_TYPE_BOSCH_SHC_C 9003
	37	#define MACH_TYPE_BOSCH_SHC_C2 9004
	38	#define MACH_TYPE_BOSCH_SHC_C3 9005
	39	#define MACH_TYPE_BOSCH_SHC 9006
	40	#ifdef CONFIG_B_SAMPLE
	41	# define CONFIG_MACH_TYPE MACH_TYPE_BOSCH_SHC_B
	42	#elif defined CONFIG_B2_SAMPLE
	43	# define CONFIG_MACH_TYPE MACH_TYPE_BOSCH_SHC_B2
	44	#elif defined CONFIG_C_SAMPLE
	45	# define CONFIG_MACH_TYPE MACH_TYPE_BOSCH_SHC_C
	46	#elif defined CONFIG_C2_SAMPLE
	47	# define CONFIG_MACH_TYPE MACH_TYPE_BOSCH_SHC_C2
	48	#elif defined CONFIG_C3_SAMPLE
	49	# define CONFIG_MACH_TYPE MACH_TYPE_BOSCH_SHC_C3
	50	#elif defined CONFIG_SERIES
	51	# define CONFIG_MACH_TYPE MACH_TYPE_BOSCH_SHC
	52	#endif /* #ifdef CONFIG_B_SAMPLE */
d8ccbe93 HS	53	/* Clock Defines */
	54	#define V_OSCK 24000000 /* Clock output from T2 */
	55	#define V_SCLK (V_OSCK)
	56
d8ccbe93 HS	57	#define CONFIG_ENV_IS_IN_MMC 1
	58
	59	/*
	60	* in case of SD Card or Network boot we want to have a possibility to
	61	* debrick the shc, therefore do not read environment from eMMC
	62	*/
	63	#if defined(CONFIG_SHC_SDBOOT) \|\| defined(CONFIG_SHC_NETBOOT)
	64	#define CONFIG_SYS_MMC_ENV_DEV 0
	65	#else
	66	#define CONFIG_SYS_MMC_ENV_DEV 1
	67	#endif
	68
	69	/*
	70	* Info when using boot partitions: As environment resides within first
	71	* 128 kB, MLO must start at 128 kB == 0x20000
	72	* ENV at MMC Boot0 Partition - 0/Undefined=user, 1=boot0, 2=boot1,
	73	* 4..7=general0..3
	74	*/
	75	#define CONFIG_ENV_SIZE 0x1000 /* 4 KB */
	76	#define CONFIG_ENV_OFFSET 0x7000 /* 28 kB */
	77
	78	#define CONFIG_HSMMC2_8BIT
	79
	80	#define CONFIG_ENV_OFFSET_REDUND 0x9000 /* 36 kB */
	81	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	82
	83	/* Enhance our eMMC support / experience. */
	84	#define CONFIG_CMD_GPT
d8ccbe93 HS	85	#ifndef CONFIG_SHC_ICT
	86	/*
	87	* In builds other than ICT, reset to retry after timeout
	88	* Define a timeout after which a stopped bootloader continues autoboot
	89	* (only works with CONFIG_RESET_TO_RETRY)
	90	*/
	91	# define CONFIG_BOOT_RETRY_TIME 30
	92	# define CONFIG_RESET_TO_RETRY
	93	#endif
	94
	95	#define CONFIG_ENV_VARS_UBOOT_CONFIG
	96	#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
	97
	98	#ifndef CONFIG_SPL_BUILD
	99	#define CONFIG_EXTRA_ENV_SETTINGS \
	100	"loadaddr=0x80200000\0" \
	101	"kloadaddr=0x84000000\0" \
	102	"fdtaddr=0x85000000\0" \
	103	"fdt_high=0xffffffff\0" \
	104	"rdaddr=0x81000000\0" \
	105	"bootfile=uImage\0" \
	106	"fdtfile=am335x-shc.dtb\0" \
	107	"verify=no\0" \
	108	"serverip=10.55.152.184\0" \
	109	"rootpath=/srv/nfs/shc-rootfs\0" \
	110	"console=ttyO0,115200n8\0" \
	111	"optargs=quiet\0" \
	112	"mmcdev=1\0" \
	113	"harakiri=0\0" \
	114	"mmcpart=2\0" \
	115	"active_root=root1\0" \
	116	"inactive_root=root2\0" \
	117	"mmcrootfstype=ext4 rootwait\0" \
	118	"nfsopts=nolock\0" \
	119	"static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
	120	"::off\0" \
	121	"ip_method=none\0" \
	122	"bootargs_defaults=setenv bootargs " \
	123	"console=${console} " \
	124	"${optargs}\0" \
	125	"mmcargs=run bootargs_defaults;" \
	126	"setenv bootargs ${bootargs} " \
	127	"root=${mmcroot} " \
	128	"rootfstype=${mmcrootfstype} ip=${ip_method}\0" \
	129	"netargs=setenv bootargs console=${console} " \
	130	"${optargs} " \
	131	"root=/dev/nfs " \
	132	"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
	133	"ip=dhcp\0" \
	134	"bootenv=uEnv.txt\0" \
	135	"loadbootenv=if fatload mmc ${mmcdev} ${loadaddr} ${bootenv}; then " \
	136	"echo Loaded environment from ${bootenv}; " \
	137	"run importbootenv; " \
	138	"fi;\0" \
	139	"importbootenv=echo Importing environment variables from uEnv.txt ...; " \
	140	"env import -t $loadaddr $filesize\0" \
	141	"loaduimagefat=fatload mmc ${mmcdev} ${kloadaddr} ${bootfile}\0" \
	142	"loaduimage=ext2load mmc ${mmcdev}:${mmcpart} ${kloadaddr} /boot/${bootfile}\0" \
	143	"loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdtaddr} /boot/${fdtfile}\0" \
	144	"netloaduimage=tftp ${loadaddr} ${bootfile}\0" \
	145	"netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
	146	"mmcboot=echo Booting Linux from ${mmcdevice} ...; " \
	147	"run mmcargs; " \
	148	"if run loadfdt; then " \
149	"echo device tree detected; " \
150	"bootm ${kloadaddr} - ${fdtaddr}; " \
151	"else " \
152	"bootm ${kloadaddr}; " \
153	"fi; \0" \
154	"netboot=echo Booting from network ...; " \
155	"setenv autoload no; " \
156	"dhcp; " \
157	"run netloaduimage; " \
158	"run netargs; " \
159	"echo NFS path: ${serverip}:${rootpath};" \
160	"if run netloadfdt; then " \
161	"echo device tree detected; " \
162	"bootm ${loadaddr} - ${fdtaddr}; " \
163	"else " \
164	"bootm ${loadaddr}; " \
165	"fi; \0" \
166	"emmc_erase=if test ${harakiri} = 1 ; then echo erase emmc ...; setenv mmcdev 1; mmc erase 0 200; reset; fi; \0" \
167	"mmcpart_gp=mmcpart gp 1 40; \0" \
168	"mmcpart_enhance=mmcpart enhance 0 64; \0" \
169	"mmcpart_rel_write=mmcpart rel_write 1f; \0" \
170	"mmcpart_commit=mmcpart commit 1; \0" \
171	"mmc_hw_part=run mmcpart_gp; run mmcpart_enhance; run mmcpart_rel_write; run mmcpart_commit; \0" \
172	"led_success=gpio set 22; \0" \
173	"fusecmd=mmc dev 1; if mmcpart iscommitted; then echo HW Partitioning already committed; mmcpart list; else run mmc_hw_part; fi; run led_success; \0" \
174	"uenv_exec=if test -n $uenvcmd; then " \
175	"echo Running uenvcmd ...; " \
176	"run uenvcmd; " \
177	"fi;\0" \
178	"sd_setup=echo SD/MMC-Card detected on device 0; " \
179	"setenv mmcdevice SD; " \
180	"setenv mmcdev 0; " \
181	"setenv mmcpart 2; " \
182	"setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0" \
183	"emmc_setup=echo eMMC detected on device 1; " \
184	"setenv mmcdevice eMMC; " \
185	"setenv mmcdev 1; " \
186	"run emmc_erase; " \
187	"if test ${active_root} = root2; then " \
188	"echo Active root is partition 6 (root2); " \
189	"setenv mmcpart 6; " \
190	"else " \
191	"echo Active root is partition 5 (root1); " \
192	"setenv mmcpart 5; " \
193	"fi; " \
194	"setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0"
195	#endif /* #ifndef CONFIG_SPL_BUILD */
196
197	#if defined CONFIG_SHC_NETBOOT
198	/* Network Boot */
199	# define CONFIG_BOOTCOMMAND \
200	"run fusecmd; " \
201	"if run netboot; then " \
202	"echo Booting from network; " \
203	"else " \
204	"echo ERROR: Cannot boot from network!; " \
205	"panic; " \
206	"fi; "
207
208	#elif defined CONFIG_SHC_SDBOOT /* !defined CONFIG_SHC_NETBOOT */
209	/* SD-Card Boot */
210	# define CONFIG_BOOTCOMMAND \
211	"if mmc dev 0; mmc rescan; then " \
212	"run sd_setup; " \
213	"else " \
214	"echo ERROR: SD/MMC-Card not detected!; " \
215	"panic; " \
216	"fi; " \
217	"if run loaduimage; then " \
218	"echo Bootable SD/MMC-Card inserted, booting from it!; " \
219	"run mmcboot; " \
220	"else " \
221	"echo ERROR: Unable to load uImage from SD/MMC-Card!; " \
222	"panic; " \
223	"fi; "
224
225	#elif defined CONFIG_SHC_ICT
226	/* ICT adapter boots only u-boot and does HW partitioning */
227	# define CONFIG_BOOTCOMMAND \
228	"if mmc dev 0; mmc rescan; then " \
229	"run sd_setup; " \
230	"else " \
231	"echo ERROR: SD/MMC-Card not detected!; " \
232	"panic; " \
233	"fi; " \
234	"run fusecmd; "
235
236	#else /* !defined CONFIG_SHC_NETBOOT, !defined CONFIG_SHC_SDBOOT */
237	/* Regular Boot from internal eMMC */
238	# define CONFIG_BOOTCOMMAND \
239	"if mmc dev 1; mmc rescan; then " \
240	"run emmc_setup; " \
241	"else " \
242	"echo ERROR: eMMC device not detected!; " \
243	"panic; " \
244	"fi; " \
245	"if run loaduimage; then " \
246	"run mmcboot; " \
247	"else " \
248	"echo ERROR Unable to load uImage from eMMC!; " \
249	"echo Performing Rollback!; " \
250	"setenv _active_ ${active_root}; " \
251	"setenv _inactive_ ${inactive_root}; " \
252	"setenv active_root ${_inactive_}; " \
253	"setenv inactive_root ${_active_}; " \
254	"saveenv; " \
255	"reset; " \
256	"fi; "
257
258	#endif /* Regular Boot */
259
260	/* NS16550 Configuration */
261	#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
262	#define CONFIG_SYS_NS16550_COM2 0x48022000 /* UART1 */
263	#define CONFIG_SYS_NS16550_COM3 0x48024000 /* UART2 */
264	#define CONFIG_SYS_NS16550_COM4 0x481a6000 /* UART3 */
265	#define CONFIG_SYS_NS16550_COM5 0x481a8000 /* UART4 */
266	#define CONFIG_SYS_NS16550_COM6 0x481aa000 /* UART5 */
267	#define CONFIG_BAUDRATE 115200
268	#define CONFIG_CONS_INDEX 1
269
270	/* PMIC support */
271	#define CONFIG_POWER_TPS65217
272
273	/* SPL */
d8ccbe93	274
983e3700	275	#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/am33xx/u-boot-spl.lds"
d8ccbe93 HS	276
d8ccbe93 HS	277	#ifndef CONFIG_SPL_USBETH_SUPPORT
d8ccbe93 HS	278	#define CONFIG_FASTBOOT_FLASH_MMC_DEV 1
	279	#endif
	280
	281	/*
	282	* Disable MMC DM for SPL build and can be re-enabled after adding
	283	* DM support in SPL
	284	*/
	285	#ifdef CONFIG_SPL_BUILD
	286	#undef CONFIG_DM_MMC
	287	#undef CONFIG_TIMER
	288	#endif
	289
	290	#define CONFIG_CMD_DHCP
	291	#define CONFIG_CMD_PING
	292	#define CONFIG_DRIVER_TI_CPSW
	293	#define CONFIG_MII
	294	#define CONFIG_BOOTP_DEFAULT
	295	#define CONFIG_BOOTP_DNS
	296	#define CONFIG_BOOTP_DNS2
	297	#define CONFIG_BOOTP_SEND_HOSTNAME
	298	#define CONFIG_BOOTP_GATEWAY
	299	#define CONFIG_BOOTP_SUBNETMASK
	300	#define CONFIG_NET_RETRY_COUNT 10
	301	#define CONFIG_NET_MULTI
	302	#define CONFIG_PHY_GIGE
	303	#define CONFIG_PHYLIB
	304	#define CONFIG_PHY_ADDR 0
	305	#define CONFIG_PHY_SMSC
	306
	307	/* I2C configuration */
	308	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */
	309	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	310	#define CONFIG_SYS_I2C_SPEED 400000
	311	#define CONFIG_SYS_I2C_SLAVE 1
	312
	313	#define CONFIG_SHOW_BOOT_PROGRESS
	314
	315	#if defined CONFIG_SHC_NETBOOT
	316	#ifdef CONFIG_SPL_BUILD
d8ccbe93 HS	317	#define CONFIG_ENV_IS_NOWHERE
	318	#undef CONFIG_ENV_IS_IN_MMC
	319	#endif
	320	#endif
	321	#endif /* ! __CONFIG_AM335X_SHC_H */