[J-u-boot.git] / doc / README.fec_mxc

U-Boot config options used in fec_mxc.c

CONFIG_FEC_MXC
	Selects fec_mxc.c to be compiled into u-boot. Can read out the
	ethaddr from the SoC eFuses (see below).

CONFIG_MII
	Must be defined if CONFIG_FEC_MXC is defined.

CONFIG_FEC_XCV_TYPE
	Defaults to MII100 for 100 Base-tx.
	RGMII selects 1000 Base-tx reduced pin count interface.
	RMII selects 100 Base-tx reduced pin count interface.

CONFIG_FEC_MXC_SWAP_PACKET
	Forced on iff MX28.
	Swaps the bytes order of all words(4 byte units) in the packet.
	This should not be specified by a board file. It is cpu specific.

CONFIG_PHYLIB
	fec_mxc supports PHYLIB and should be used for new boards.

CONFIG_FEC_MXC_NO_ANEG
	Relevant only if PHYLIB not used. Skips auto-negotiation restart.

CONFIG_FEC_MXC_PHYADDR
	Optional, selects the exact phy address that should be connected
	and function fecmxc_initialize will try to initialize it.

CONFIG_FEC_FIXED_SPEED
	Optional, selects a fixed speed on the MAC interface without asking some
	phy. This is usefull if there is a direct MAC <-> MAC connection, for
	example if the CPU is connected directly via the RGMII interface to a
	ethernet-switch.

Reading the ethaddr from the SoC eFuses:
if CONFIG_FEC_MXC is defined and the U-Boot environment does not contain the
ethaddr variable, then its value gets read from the corresponding eFuses in
the SoC. See the README files of the specific SoC for details.
Commit	Line	Data
a187559e	1	U-Boot config options used in fec_mxc.c
c30eab2d TK	2
c30eab2d TK	3	CONFIG_FEC_MXC
95c69223 OM	4	Selects fec_mxc.c to be compiled into u-boot. Can read out the
95c69223 OM	5	ethaddr from the SoC eFuses (see below).
c30eab2d TK	6
	7	CONFIG_MII
	8	Must be defined if CONFIG_FEC_MXC is defined.
	9
	10	CONFIG_FEC_XCV_TYPE
	11	Defaults to MII100 for 100 Base-tx.
	12	RGMII selects 1000 Base-tx reduced pin count interface.
	13	RMII selects 100 Base-tx reduced pin count interface.
	14
	15	CONFIG_FEC_MXC_SWAP_PACKET
	16	Forced on iff MX28.
	17	Swaps the bytes order of all words(4 byte units) in the packet.
	18	This should not be specified by a board file. It is cpu specific.
	19
	20	CONFIG_PHYLIB
	21	fec_mxc supports PHYLIB and should be used for new boards.
	22
	23	CONFIG_FEC_MXC_NO_ANEG
	24	Relevant only if PHYLIB not used. Skips auto-negotiation restart.
	25
	26	CONFIG_FEC_MXC_PHYADDR
	27	Optional, selects the exact phy address that should be connected
	28	and function fecmxc_initialize will try to initialize it.
95c69223	29
0750701a HS	30	CONFIG_FEC_FIXED_SPEED
	31	Optional, selects a fixed speed on the MAC interface without asking some
	32	phy. This is usefull if there is a direct MAC <-> MAC connection, for
	33	example if the CPU is connected directly via the RGMII interface to a
	34	ethernet-switch.
95c69223 OM	35
	36	Reading the ethaddr from the SoC eFuses:
	37	if CONFIG_FEC_MXC is defined and the U-Boot environment does not contain the
	38	ethaddr variable, then its value gets read from the corresponding eFuses in
	39	the SoC. See the README files of the specific SoC for details.