[J-u-boot.git] / include / ahci.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright (C) Freescale Semiconductor, Inc. 2006.
 * Author: Jason Jin<[email protected]>
 *         Zhang Wei<[email protected]>
 */
#ifndef _AHCI_H_
#define _AHCI_H_

#include <pci.h>

#define AHCI_PCI_BAR		0x24
#define AHCI_MAX_SG		56 /* hardware max is 64K */
#define AHCI_CMD_SLOT_SZ	32
#define AHCI_MAX_CMD_SLOT	32
#define AHCI_RX_FIS_SZ		256
#define AHCI_CMD_TBL_HDR	0x80
#define AHCI_CMD_TBL_CDB	0x40
#define AHCI_CMD_TBL_SZ		AHCI_CMD_TBL_HDR + (AHCI_MAX_SG * 16)
#define AHCI_PORT_PRIV_DMA_SZ	(AHCI_CMD_SLOT_SZ * AHCI_MAX_CMD_SLOT + \
				AHCI_CMD_TBL_SZ	+ AHCI_RX_FIS_SZ)
#define AHCI_CMD_ATAPI		(1 << 5)
#define AHCI_CMD_WRITE		(1 << 6)
#define AHCI_CMD_PREFETCH	(1 << 7)
#define AHCI_CMD_RESET		(1 << 8)
#define AHCI_CMD_CLR_BUSY	(1 << 10)

#define RX_FIS_D2H_REG		0x40	/* offset of D2H Register FIS data */

/* Global controller registers */
#define HOST_CAP		0x00 /* host capabilities */
#define HOST_CTL		0x04 /* global host control */
#define HOST_IRQ_STAT		0x08 /* interrupt status */
#define HOST_PORTS_IMPL		0x0c /* bitmap of implemented ports */
#define HOST_VERSION		0x10 /* AHCI spec. version compliancy */
#define HOST_CAP2		0x24 /* host capabilities, extended */

/* HOST_CTL bits */
#define HOST_RESET		(1 << 0)  /* reset controller; self-clear */
#define HOST_IRQ_EN		(1 << 1)  /* global IRQ enable */
#define HOST_AHCI_EN		(1 << 31) /* AHCI enabled */

/* Registers for each SATA port */
#define PORT_LST_ADDR		0x00 /* command list DMA addr */
#define PORT_LST_ADDR_HI	0x04 /* command list DMA addr hi */
#define PORT_FIS_ADDR		0x08 /* FIS rx buf addr */
#define PORT_FIS_ADDR_HI	0x0c /* FIS rx buf addr hi */
#define PORT_IRQ_STAT		0x10 /* interrupt status */
#define PORT_IRQ_MASK		0x14 /* interrupt enable/disable mask */
#define PORT_CMD		0x18 /* port command */
#define PORT_TFDATA		0x20 /* taskfile data */
#define PORT_SIG		0x24 /* device TF signature */
#define PORT_CMD_ISSUE		0x38 /* command issue */
#define PORT_SCR		0x28 /* SATA phy register block */
#define PORT_SCR_STAT		0x28 /* SATA phy register: SStatus */
#define PORT_SCR_CTL		0x2c /* SATA phy register: SControl */
#define PORT_SCR_ERR		0x30 /* SATA phy register: SError */
#define PORT_SCR_ACT		0x34 /* SATA phy register: SActive */

#ifdef CONFIG_SUNXI_AHCI
#define PORT_P0DMACR		0x70 /* SUNXI specific "DMA register" */
#endif

/* PORT_IRQ_{STAT,MASK} bits */
#define PORT_IRQ_COLD_PRES	(1 << 31) /* cold presence detect */
#define PORT_IRQ_TF_ERR		(1 << 30) /* task file error */
#define PORT_IRQ_HBUS_ERR	(1 << 29) /* host bus fatal error */
#define PORT_IRQ_HBUS_DATA_ERR	(1 << 28) /* host bus data error */
#define PORT_IRQ_IF_ERR		(1 << 27) /* interface fatal error */
#define PORT_IRQ_IF_NONFATAL	(1 << 26) /* interface non-fatal error */
#define PORT_IRQ_OVERFLOW	(1 << 24) /* xfer exhausted available S/G */
#define PORT_IRQ_BAD_PMP	(1 << 23) /* incorrect port multiplier */

#define PORT_IRQ_PHYRDY		(1 << 22) /* PhyRdy changed */
#define PORT_IRQ_DEV_ILCK	(1 << 7) /* device interlock */
#define PORT_IRQ_CONNECT	(1 << 6) /* port connect change status */
#define PORT_IRQ_SG_DONE	(1 << 5) /* descriptor processed */
#define PORT_IRQ_UNK_FIS	(1 << 4) /* unknown FIS rx'd */
#define PORT_IRQ_SDB_FIS	(1 << 3) /* Set Device Bits FIS rx'd */
#define PORT_IRQ_DMAS_FIS	(1 << 2) /* DMA Setup FIS rx'd */
#define PORT_IRQ_PIOS_FIS	(1 << 1) /* PIO Setup FIS rx'd */
#define PORT_IRQ_D2H_REG_FIS	(1 << 0) /* D2H Register FIS rx'd */

#define PORT_IRQ_FATAL		PORT_IRQ_TF_ERR | PORT_IRQ_HBUS_ERR	\
				| PORT_IRQ_HBUS_DATA_ERR | PORT_IRQ_IF_ERR

#define DEF_PORT_IRQ		PORT_IRQ_FATAL | PORT_IRQ_PHYRDY	\
				| PORT_IRQ_CONNECT | PORT_IRQ_SG_DONE	\
				| PORT_IRQ_UNK_FIS | PORT_IRQ_SDB_FIS	\
				| PORT_IRQ_DMAS_FIS | PORT_IRQ_PIOS_FIS	\
				| PORT_IRQ_D2H_REG_FIS

/* PORT_SCR_STAT bits */
#define PORT_SCR_STAT_DET_MASK	0x3
#define PORT_SCR_STAT_DET_COMINIT 0x1
#define PORT_SCR_STAT_DET_PHYRDY 0x3

/* PORT_CMD bits */
#define PORT_CMD_ATAPI		(1 << 24) /* Device is ATAPI */
#define PORT_CMD_LIST_ON	(1 << 15) /* cmd list DMA engine running */
#define PORT_CMD_FIS_ON		(1 << 14) /* FIS DMA engine running */
#define PORT_CMD_FIS_RX		(1 << 4) /* Enable FIS receive DMA engine */
#define PORT_CMD_CLO		(1 << 3) /* Command list override */
#define PORT_CMD_POWER_ON	(1 << 2) /* Power up device */
#define PORT_CMD_SPIN_UP	(1 << 1) /* Spin up device */
#define PORT_CMD_START		(1 << 0) /* Enable port DMA engine */

#define PORT_CMD_ICC_ACTIVE	(0x1 << 28) /* Put i/f in active state */
#define PORT_CMD_ICC_PARTIAL	(0x2 << 28) /* Put i/f in partial state */
#define PORT_CMD_ICC_SLUMBER	(0x6 << 28) /* Put i/f in slumber state */

#define AHCI_MAX_PORTS		32

#define ATA_FLAG_SATA		(1 << 3)
#define ATA_FLAG_NO_LEGACY	(1 << 4) /* no legacy mode check */
#define ATA_FLAG_MMIO		(1 << 6) /* use MMIO, not PIO */
#define ATA_FLAG_SATA_RESET	(1 << 7) /* (obsolete) use COMRESET */
#define ATA_FLAG_PIO_DMA	(1 << 8) /* PIO cmds via DMA */
#define ATA_FLAG_NO_ATAPI	(1 << 11) /* No ATAPI support */

struct ahci_cmd_hdr {
	u32	opts;
	u32	status;
	u32	tbl_addr;
	u32	tbl_addr_hi;
	u32	reserved[4];
};

struct ahci_sg {
	u32	addr;
	u32	addr_hi;
	u32	reserved;
	u32	flags_size;
};

struct ahci_ioports {
	void __iomem	*port_mmio;
	struct ahci_cmd_hdr	*cmd_slot;
	struct ahci_sg		*cmd_tbl_sg;
	ulong	cmd_tbl;
	u32	rx_fis;
};

/**
 * struct ahci_uc_priv - information about an AHCI controller
 *
 * When driver model is used, this is accessible using dev_get_uclass_priv(dev)
 * where dev is the controller (although at present it sometimes stands alone).
 */
struct ahci_uc_priv {
	/*
	 * TODO([email protected]): Drop this once this structure is only used
	 * in a driver-model context (i.e. attached to a device with
	 * dev_get_uclass_priv()
	 */
	struct udevice *dev;
	struct ahci_ioports	port[AHCI_MAX_PORTS];
	u16 *ataid[AHCI_MAX_PORTS];
	u32	n_ports;
	u32	hard_port_no;
	u32	host_flags;
	u32	host_set_flags;
	void __iomem *mmio_base;
	u32     pio_mask;
	u32	udma_mask;
	u32	flags;
	u32	cap;	/* cache of HOST_CAP register */
	u32	port_map; /* cache of HOST_PORTS_IMPL reg */
	u32	link_port_map; /*linkup port map*/
};

struct ahci_ops {
	/**
	 * reset() - reset the controller
	 *
	 * @dev:	Controller to reset
	 * @return 0 if OK, -ve on error
	 */
	int (*reset)(struct udevice *dev);

	/**
	 * port_status() - get the status of a SATA port
	 *
	 * @dev:	Controller to reset
	 * @port:	Port number to check (0 for first)
	 * @return 0 if detected, -ENXIO if nothing on port, other -ve on error
	 */
	int (*port_status)(struct udevice *dev, int port);

	/**
	 * scan() - scan SATA ports
	 *
	 * @dev:	Controller to scan
	 * @return 0 if OK, -ve on error
	 */
	int (*scan)(struct udevice *dev);
};

#define ahci_get_ops(dev)        ((struct ahci_ops *)(dev)->driver->ops)

/**
 * sata_reset() - reset the controller
 *
 * @dev:	Controller to reset
 * Return: 0 if OK, -ve on error
 */
int sata_reset(struct udevice *dev);

/**
 * sata_port_status() - get the status of a SATA port
 *
 * @dev:	Controller to reset
 * @port:	Port number to check (0 for first)
 * Return: 0 if detected, -ENXIO if nothin on port, other -ve on error
 */
int sata_dm_port_status(struct udevice *dev, int port);

/**
 * sata_scan() - scan SATA ports
 *
 * @dev:	Controller to scan
 * Return: 0 if OK, -ve on error
 */
int sata_scan(struct udevice *dev);

/**
 * ahci_init_one_dm() - set up a single AHCI port
 *
 * @dev: Controller to init
 */
int ahci_init_one_dm(struct udevice *dev);

/**
 * ahci_start_ports_dm() - start all AHCI ports for a controller
 *
 * @dev: Controller containing ports to start
 */
int ahci_start_ports_dm(struct udevice *dev);

/**
 * ahci_init_dm() - init AHCI for a controller, finding all ports
 *
 * @dev: Device to init
 */
int ahci_init_dm(struct udevice *dev, void __iomem *base);

/**
 * ahci_bind_scsi() - bind a new SCSI bus as a child
 *
 * Note that the SCSI bus device will itself bind block devices
 *
 * @ahci_dev: AHCI parent device
 * @devp: Returns new SCSI bus device
 * Return: 0 if OK, -ve on error
 */
int ahci_bind_scsi(struct udevice *ahci_dev, struct udevice **devp);

/**
 * ahci_probe_scsi() - probe and scan the attached SCSI bus
 *
 * Note that the SCSI device will itself bind block devices for any storage
 * devices it finds.
 *
 * @ahci_dev: AHCI parent device
 * @base: Base address of AHCI port
 * Return: 0 if OK, -ve on error
 */
int ahci_probe_scsi(struct udevice *ahci_dev, ulong base);

/**
 * ahci_probe_scsi_pci() - probe and scan the attached SCSI bus on PCI
 *
 * Note that the SCSI device will itself bind block devices for any storage
 * devices it finds.
 *
 * @ahci_dev: AHCI parent device
 * Return: 0 if OK, -ve on error
 */
int ahci_probe_scsi_pci(struct udevice *ahci_dev);

#endif
Commit	Line	Data
83d290c5	1	/* SPDX-License-Identifier: GPL-2.0+ */
4782ac80	2	/*
4c2e3da8	3	* Copyright (C) Freescale Semiconductor, Inc. 2006.
4782ac80 JZ	4	* Author: Jason Jin<[email protected]>
4782ac80 JZ	5	* Zhang Wei<[email protected]>
4782ac80 JZ	6	*/
	7	#ifndef _AHCI_H_
	8	#define _AHCI_H_
	9
942e3143 RH	10	#include <pci.h>
942e3143 RH	11
4782ac80 JZ	12	#define AHCI_PCI_BAR 0x24
	13	#define AHCI_MAX_SG 56 /* hardware max is 64K */
	14	#define AHCI_CMD_SLOT_SZ 32
9f472e65	15	#define AHCI_MAX_CMD_SLOT 32
4782ac80 JZ	16	#define AHCI_RX_FIS_SZ 256
	17	#define AHCI_CMD_TBL_HDR 0x80
	18	#define AHCI_CMD_TBL_CDB 0x40
	19	#define AHCI_CMD_TBL_SZ AHCI_CMD_TBL_HDR + (AHCI_MAX_SG * 16)
9f472e65 SB	20	#define AHCI_PORT_PRIV_DMA_SZ (AHCI_CMD_SLOT_SZ * AHCI_MAX_CMD_SLOT + \
9f472e65 SB	21	AHCI_CMD_TBL_SZ + AHCI_RX_FIS_SZ)
4782ac80 JZ	22	#define AHCI_CMD_ATAPI (1 << 5)
	23	#define AHCI_CMD_WRITE (1 << 6)
	24	#define AHCI_CMD_PREFETCH (1 << 7)
	25	#define AHCI_CMD_RESET (1 << 8)
	26	#define AHCI_CMD_CLR_BUSY (1 << 10)
	27
	28	#define RX_FIS_D2H_REG 0x40 /* offset of D2H Register FIS data */
	29
	30	/* Global controller registers */
	31	#define HOST_CAP 0x00 /* host capabilities */
	32	#define HOST_CTL 0x04 /* global host control */
	33	#define HOST_IRQ_STAT 0x08 /* interrupt status */
	34	#define HOST_PORTS_IMPL 0x0c /* bitmap of implemented ports */
	35	#define HOST_VERSION 0x10 /* AHCI spec. version compliancy */
4e422bce	36	#define HOST_CAP2 0x24 /* host capabilities, extended */
4782ac80 JZ	37
	38	/* HOST_CTL bits */
	39	#define HOST_RESET (1 << 0) /* reset controller; self-clear */
	40	#define HOST_IRQ_EN (1 << 1) /* global IRQ enable */
	41	#define HOST_AHCI_EN (1 << 31) /* AHCI enabled */
	42
	43	/* Registers for each SATA port */
	44	#define PORT_LST_ADDR 0x00 /* command list DMA addr */
	45	#define PORT_LST_ADDR_HI 0x04 /* command list DMA addr hi */
	46	#define PORT_FIS_ADDR 0x08 /* FIS rx buf addr */
	47	#define PORT_FIS_ADDR_HI 0x0c /* FIS rx buf addr hi */
	48	#define PORT_IRQ_STAT 0x10 /* interrupt status */
	49	#define PORT_IRQ_MASK 0x14 /* interrupt enable/disable mask */
	50	#define PORT_CMD 0x18 /* port command */
	51	#define PORT_TFDATA 0x20 /* taskfile data */
	52	#define PORT_SIG 0x24 /* device TF signature */
	53	#define PORT_CMD_ISSUE 0x38 /* command issue */
	54	#define PORT_SCR 0x28 /* SATA phy register block */
	55	#define PORT_SCR_STAT 0x28 /* SATA phy register: SStatus */
	56	#define PORT_SCR_CTL 0x2c /* SATA phy register: SControl */
	57	#define PORT_SCR_ERR 0x30 /* SATA phy register: SError */
	58	#define PORT_SCR_ACT 0x34 /* SATA phy register: SActive */
	59
a6e50a88 IC	60	#ifdef CONFIG_SUNXI_AHCI
	61	#define PORT_P0DMACR 0x70 /* SUNXI specific "DMA register" */
	62	#endif
	63
4782ac80 JZ	64	/* PORT_IRQ_{STAT,MASK} bits */
	65	#define PORT_IRQ_COLD_PRES (1 << 31) /* cold presence detect */
	66	#define PORT_IRQ_TF_ERR (1 << 30) /* task file error */
	67	#define PORT_IRQ_HBUS_ERR (1 << 29) /* host bus fatal error */
	68	#define PORT_IRQ_HBUS_DATA_ERR (1 << 28) /* host bus data error */
	69	#define PORT_IRQ_IF_ERR (1 << 27) /* interface fatal error */
	70	#define PORT_IRQ_IF_NONFATAL (1 << 26) /* interface non-fatal error */
	71	#define PORT_IRQ_OVERFLOW (1 << 24) /* xfer exhausted available S/G */
	72	#define PORT_IRQ_BAD_PMP (1 << 23) /* incorrect port multiplier */
	73
	74	#define PORT_IRQ_PHYRDY (1 << 22) /* PhyRdy changed */
	75	#define PORT_IRQ_DEV_ILCK (1 << 7) /* device interlock */
	76	#define PORT_IRQ_CONNECT (1 << 6) /* port connect change status */
	77	#define PORT_IRQ_SG_DONE (1 << 5) /* descriptor processed */
	78	#define PORT_IRQ_UNK_FIS (1 << 4) /* unknown FIS rx'd */
	79	#define PORT_IRQ_SDB_FIS (1 << 3) /* Set Device Bits FIS rx'd */
	80	#define PORT_IRQ_DMAS_FIS (1 << 2) /* DMA Setup FIS rx'd */
	81	#define PORT_IRQ_PIOS_FIS (1 << 1) /* PIO Setup FIS rx'd */
	82	#define PORT_IRQ_D2H_REG_FIS (1 << 0) /* D2H Register FIS rx'd */
	83
53677ef1	84	#define PORT_IRQ_FATAL PORT_IRQ_TF_ERR \| PORT_IRQ_HBUS_ERR \
4782ac80 JZ	85	\| PORT_IRQ_HBUS_DATA_ERR \| PORT_IRQ_IF_ERR
4782ac80 JZ	86
53677ef1 WD	87	#define DEF_PORT_IRQ PORT_IRQ_FATAL \| PORT_IRQ_PHYRDY \
	88	\| PORT_IRQ_CONNECT \| PORT_IRQ_SG_DONE \
	89	\| PORT_IRQ_UNK_FIS \| PORT_IRQ_SDB_FIS \
4782ac80 JZ	90	\| PORT_IRQ_DMAS_FIS \| PORT_IRQ_PIOS_FIS \
	91	\| PORT_IRQ_D2H_REG_FIS
	92
2bdb10db RH	93	/* PORT_SCR_STAT bits */
	94	#define PORT_SCR_STAT_DET_MASK 0x3
	95	#define PORT_SCR_STAT_DET_COMINIT 0x1
	96	#define PORT_SCR_STAT_DET_PHYRDY 0x3
	97
4782ac80 JZ	98	/* PORT_CMD bits */
	99	#define PORT_CMD_ATAPI (1 << 24) /* Device is ATAPI */
	100	#define PORT_CMD_LIST_ON (1 << 15) /* cmd list DMA engine running */
	101	#define PORT_CMD_FIS_ON (1 << 14) /* FIS DMA engine running */
	102	#define PORT_CMD_FIS_RX (1 << 4) /* Enable FIS receive DMA engine */
	103	#define PORT_CMD_CLO (1 << 3) /* Command list override */
	104	#define PORT_CMD_POWER_ON (1 << 2) /* Power up device */
	105	#define PORT_CMD_SPIN_UP (1 << 1) /* Spin up device */
	106	#define PORT_CMD_START (1 << 0) /* Enable port DMA engine */
	107
	108	#define PORT_CMD_ICC_ACTIVE (0x1 << 28) /* Put i/f in active state */
	109	#define PORT_CMD_ICC_PARTIAL (0x2 << 28) /* Put i/f in partial state */
	110	#define PORT_CMD_ICC_SLUMBER (0x6 << 28) /* Put i/f in slumber state */
	111
	112	#define AHCI_MAX_PORTS 32
	113
4782ac80 JZ	114	#define ATA_FLAG_SATA (1 << 3)
	115	#define ATA_FLAG_NO_LEGACY (1 << 4) /* no legacy mode check */
	116	#define ATA_FLAG_MMIO (1 << 6) /* use MMIO, not PIO */
	117	#define ATA_FLAG_SATA_RESET (1 << 7) /* (obsolete) use COMRESET */
	118	#define ATA_FLAG_PIO_DMA (1 << 8) /* PIO cmds via DMA */
	119	#define ATA_FLAG_NO_ATAPI (1 << 11) /* No ATAPI support */
	120
	121	struct ahci_cmd_hdr {
	122	u32 opts;
	123	u32 status;
	124	u32 tbl_addr;
	125	u32 tbl_addr_hi;
	126	u32 reserved[4];
	127	};
	128
	129	struct ahci_sg {
	130	u32 addr;
	131	u32 addr_hi;
	132	u32 reserved;
	133	u32 flags_size;
	134	};
	135
	136	struct ahci_ioports {
fa31377e	137	void __iomem *port_mmio;
4782ac80 JZ	138	struct ahci_cmd_hdr *cmd_slot;
4782ac80 JZ	139	struct ahci_sg *cmd_tbl_sg;
fa31377e	140	ulong cmd_tbl;
4782ac80 JZ	141	u32 rx_fis;
	142	};
	143
2c9f9efb SG	144	/**
	145	* struct ahci_uc_priv - information about an AHCI controller
	146	*
	147	* When driver model is used, this is accessible using dev_get_uclass_priv(dev)
	148	* where dev is the controller (although at present it sometimes stands alone).
	149	*/
	150	struct ahci_uc_priv {
2c9f9efb SG	151	/*
	152	* TODO([email protected]): Drop this once this structure is only used
	153	* in a driver-model context (i.e. attached to a device with
	154	* dev_get_uclass_priv()
	155	*/
ff758ccc	156	struct udevice *dev;
4782ac80	157	struct ahci_ioports port[AHCI_MAX_PORTS];
4b62b2ff	158	u16 *ataid[AHCI_MAX_PORTS];
4782ac80 JZ	159	u32 n_ports;
	160	u32 hard_port_no;
	161	u32 host_flags;
	162	u32 host_set_flags;
9efaca3e	163	void __iomem *mmio_base;
4782ac80 JZ	164	u32 pio_mask;
	165	u32 udma_mask;
	166	u32 flags;
	167	u32 cap; /* cache of HOST_CAP register */
	168	u32 port_map; /* cache of HOST_PORTS_IMPL reg */
	169	u32 link_port_map; /linkup port map/
	170	};
	171
b8341f1c SG	172	struct ahci_ops {
	173	/**
	174	* reset() - reset the controller
	175	*
	176	* @dev: Controller to reset
	177	* @return 0 if OK, -ve on error
	178	*/
	179	int (reset)(struct udevice dev);
	180
	181	/**
	182	* port_status() - get the status of a SATA port
	183	*
	184	* @dev: Controller to reset
	185	* @port: Port number to check (0 for first)
	186	* @return 0 if detected, -ENXIO if nothing on port, other -ve on error
	187	*/
	188	int (port_status)(struct udevice dev, int port);
	189
	190	/**
	191	* scan() - scan SATA ports
	192	*
	193	* @dev: Controller to scan
	194	* @return 0 if OK, -ve on error
	195	*/
	196	int (scan)(struct udevice dev);
	197	};
	198
	199	#define ahci_get_ops(dev) ((struct ahci_ops *)(dev)->driver->ops)
	200
	201	/**
	202	* sata_reset() - reset the controller
	203	*
	204	* @dev: Controller to reset
185f812c	205	* Return: 0 if OK, -ve on error
b8341f1c SG	206	*/
	207	int sata_reset(struct udevice *dev);
	208
	209	/**
	210	* sata_port_status() - get the status of a SATA port
	211	*
	212	* @dev: Controller to reset
	213	* @port: Port number to check (0 for first)
185f812c	214	* Return: 0 if detected, -ENXIO if nothin on port, other -ve on error
b8341f1c SG	215	*/
	216	int sata_dm_port_status(struct udevice *dev, int port);
	217
	218	/**
	219	* sata_scan() - scan SATA ports
	220	*
	221	* @dev: Controller to scan
185f812c	222	* Return: 0 if OK, -ve on error
b8341f1c SG	223	*/
	224	int sata_scan(struct udevice *dev);
	225
7cf1afce	226	/**
e81589ea	227	* ahci_init_one_dm() - set up a single AHCI port
7cf1afce SG	228	*
	229	* @dev: Controller to init
	230	*/
e81589ea	231	int ahci_init_one_dm(struct udevice *dev);
7cf1afce SG	232
7cf1afce SG	233	/**
e81589ea	234	* ahci_start_ports_dm() - start all AHCI ports for a controller
7cf1afce SG	235	*
	236	* @dev: Controller containing ports to start
	237	*/
e81589ea	238	int ahci_start_ports_dm(struct udevice *dev);
7cf1afce	239
4279efc4 SG	240	/**
	241	* ahci_init_dm() - init AHCI for a controller, finding all ports
	242	*
	243	* @dev: Device to init
	244	*/
	245	int ahci_init_dm(struct udevice dev, void __iomem base);
	246
681357ff SG	247	/**
	248	* ahci_bind_scsi() - bind a new SCSI bus as a child
	249	*
	250	* Note that the SCSI bus device will itself bind block devices
	251	*
	252	* @ahci_dev: AHCI parent device
	253	* @devp: Returns new SCSI bus device
185f812c	254	* Return: 0 if OK, -ve on error
681357ff SG	255	*/
	256	int ahci_bind_scsi(struct udevice ahci_dev, struct udevice *devp);
	257
	258	/**
	259	* ahci_probe_scsi() - probe and scan the attached SCSI bus
	260	*
	261	* Note that the SCSI device will itself bind block devices for any storage
	262	* devices it finds.
	263	*
	264	* @ahci_dev: AHCI parent device
745a94f3	265	* @base: Base address of AHCI port
185f812c	266	* Return: 0 if OK, -ve on error
681357ff	267	*/
745a94f3 SG	268	int ahci_probe_scsi(struct udevice *ahci_dev, ulong base);
	269
	270	/**
	271	* ahci_probe_scsi_pci() - probe and scan the attached SCSI bus on PCI
	272	*
	273	* Note that the SCSI device will itself bind block devices for any storage
	274	* devices it finds.
	275	*
	276	* @ahci_dev: AHCI parent device
185f812c	277	* Return: 0 if OK, -ve on error
745a94f3 SG	278	*/
745a94f3 SG	279	int ahci_probe_scsi_pci(struct udevice *ahci_dev);
681357ff	280
4782ac80	281	#endif