[J-u-boot.git] / include / configs / bf533-ezkit.h

/*
 * U-boot - Configuration file for BF533 EZKIT board
 */

#ifndef __CONFIG_EZKIT533_H__
#define __CONFIG_EZKIT533_H__

#define CONFIG_BAUDRATE		57600
#define CONFIG_STAMP		1

#define CONFIG_BOOTDELAY	5
#define CFG_AUTOLOAD		"no"	/*rarpb, bootp or dhcp commands will perform only a */

#define CFG_LONGHELP		1
#define CONFIG_CMDLINE_EDITING	1
#define CONFIG_LOADADDR		0x01000000	/* default load address */
#define CONFIG_BOOTCOMMAND	"tftp $(loadaddr) linux"
/* #define CONFIG_BOOTARGS		"root=/dev/mtdblock0 rw" */

#define CONFIG_DRIVER_SMC91111	1
#define CONFIG_SMC91111_BASE	0x20310300

#if 0
#define	CONFIG_MII
#define CFG_DISCOVER_PHY
#endif

#define CONFIG_RTC_BFIN		1
#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, currently its disabled */

/*
 * Boot Mode Set
 * Blackfin can support several boot modes
 */
#define BF533_BYPASS_BOOT	0x0001	/* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
#define BF533_PARA_BOOT		0x0002	/* Bootmode 1: Boot from 8-bit or 16-bit flash */
#define BF533_SPI_BOOT		0x0004	/* Bootmode 3: Boot from SPI flash */
/* Define the boot mode */
#define BFIN_BOOT_MODE		BF533_BYPASS_BOOT
/* #define BFIN_BOOT_MODE	BF533_SPI_BOOT */

#define CONFIG_PANIC_HANG 1

#define ADSP_BF531		0x31
#define ADSP_BF532		0x32
#define ADSP_BF533		0x33
#define BFIN_CPU		ADSP_BF533

/* This sets the default state of the cache on U-Boot's boot */
#define CONFIG_ICACHE_ON
#define CONFIG_DCACHE_ON

/* Define where the uboot will be loaded by on-chip boot rom */
#define APP_ENTRY 0x00001000

/* CONFIG_CLKIN_HZ is any value in Hz				*/
#define CONFIG_CLKIN_HZ		27000000
/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	*/
/*						    1=CLKIN/2	*/
#define CONFIG_CLKIN_HALF	0
/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass	*/
/*						 1=bypass PLL	*/
#define CONFIG_PLL_BYPASS	0
/* CONFIG_VCO_MULT controls what the multiplier of the PLL is.	*/
/* Values can range from 1-64					*/
#define CONFIG_VCO_MULT		22
/* CONFIG_CCLK_DIV controls what the core clock divider is	*/
/* Values can be 1, 2, 4, or 8 ONLY				*/
#define CONFIG_CCLK_DIV		1
/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
/* Values can range from 1-15					*/
#define CONFIG_SCLK_DIV		5
/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider	*/
/* Values can range from 2-65535				*/
/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD)			*/
#define CONFIG_SPI_BAUD		2
#define CONFIG_SPI_BAUD_INITBLOCK	4

#if ( CONFIG_CLKIN_HALF == 0 )
#define CONFIG_VCO_HZ		( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
#else
#define CONFIG_VCO_HZ		(( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
#endif

#if (CONFIG_PLL_BYPASS == 0)
#define CONFIG_CCLK_HZ		( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
#define CONFIG_SCLK_HZ		( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
#else
#define CONFIG_CCLK_HZ		CONFIG_CLKIN_HZ
#define CONFIG_SCLK_HZ		CONFIG_CLKIN_HZ
#endif

#define CONFIG_MEM_SIZE		32	/* 128, 64, 32, 16 */
#define CONFIG_MEM_ADD_WDTH	9	/* 8, 9, 10, 11    */
#define CONFIG_MEM_MT48LC16M16A2TG_75	1

#define CONFIG_LOADS_ECHO	1


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_PING
#define CONFIG_CMD_ELF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_DATE


#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"

#define	CFG_PROMPT		"ezkit> "	/* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define	CFG_CBSIZE		1024	/* Console I/O Buffer Size */
#else
#define	CFG_CBSIZE		256	/* Console I/O Buffer Size */
#endif
#define	CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
#define	CFG_MAXARGS		16	/* max number of command args */
#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
#define CFG_MEMTEST_START	0x00000000	/* memtest works on */
#define CFG_MEMTEST_END		( (CONFIG_MEM_SIZE - 1) * 1024 * 1024)	/* 1 ... 31 MB in DRAM */
#define	CFG_LOAD_ADDR		0x01000000	/* default load address */
#define	CFG_HZ			1000	/* decrementer freq: 10 ms ticks */
#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
#define	CFG_SDRAM_BASE		0x00000000
#define CFG_MAX_RAM_SIZE	(CONFIG_MEM_SIZE * 1024 * 1024)
#define CFG_FLASH_BASE		0x20000000

#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
#define CFG_MONITOR_BASE	(CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
#define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
#define CFG_GBL_DATA_SIZE	0x4000
#define CFG_GBL_DATA_ADDR	(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
#define CONFIG_STACKBASE	(CFG_GBL_DATA_ADDR  - 4)

#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
#define CFG_FLASH0_BASE		0x20000000
#define CFG_FLASH1_BASE		0x20200000
#define CFG_FLASH2_BASE		0x20280000
#define CFG_MAX_FLASH_BANKS	3	/* max number of memory banks */
#define CFG_MAX_FLASH_SECT	40	/* max number of sectors on one chip */

#define	CFG_ENV_IS_IN_FLASH	1
#define CFG_ENV_ADDR		0x20020000
#define	CFG_ENV_SECT_SIZE	0x10000	/* Total Size of Environment Sector */

/* JFFS Partition offset set  */
#define CFG_JFFS2_FIRST_BANK	0
#define CFG_JFFS2_NUM_BANKS	1
/* 512k reserved for u-boot */
#define CFG_JFFS2_FIRST_SECTOR	11


/*
 * Stack sizes
 */
#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */

#define POLL_MODE		1
#define FLASH_TOT_SECT		40
#define FLASH_SIZE		0x220000
#define CFG_FLASH_SIZE		0x220000

/*
 * Initialize PSD4256 registers for using I2C
 */
#define	CONFIG_MISC_INIT_R

/*
 * I2C settings
 * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
 */
#define CONFIG_SOFT_I2C		1	/* I2C bit-banged */
/*
 * Software (bit-bang) I2C driver configuration
 */
#define PF_SCL			PF0
#define PF_SDA			PF1

#define I2C_INIT		(*pFIO_DIR |=  PF_SCL); asm("ssync;")
#define I2C_ACTIVE		(*pFIO_DIR |=  PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
#define I2C_TRISTATE		(*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
#define I2C_READ		((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
#define I2C_SDA(bit)	if(bit) { \
				*pFIO_FLAG_S = PF_SDA; \
				asm("ssync;"); \
				} \
			else    { \
				*pFIO_FLAG_C = PF_SDA; \
				asm("ssync;"); \
				}
#define I2C_SCL(bit)	if(bit) { \
				*pFIO_FLAG_S = PF_SCL; \
				asm("ssync;"); \
				} \
			else    { \
				*pFIO_FLAG_C = PF_SCL; \
				asm("ssync;"); \
				}
#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */

#define CFG_I2C_SPEED		50000
#define CFG_I2C_SLAVE		0xFE

#define CFG_BOOTM_LEN		0x4000000	/* Large Image Length, set to 64 Meg */

/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
/* #define AMGCTLVAL		(AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
#define AMBCTL0VAL		(B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
				~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
#define AMBCTL1VAL		(B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
				B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
*/
#define AMGCTLVAL		0xFF
#define AMBCTL0VAL		0x7BB07BB0
#define AMBCTL1VAL		0xFFC27BB0

#define CONFIG_VDSP		1

#ifdef CONFIG_VDSP
#define ET_EXEC_VDSP		0x8
#define SHT_STRTAB_VDSP		0x1
#define ELFSHDRSIZE_VDSP	0x2C
#define VDSP_ENTRY_ADDR		0xFFA00000
#endif

#endif
Commit	Line	Data
3f0606ad AL	1	/*
	2	* U-boot - Configuration file for BF533 EZKIT board
	3	*/
	4
	5	#ifndef __CONFIG_EZKIT533_H__
	6	#define __CONFIG_EZKIT533_H__
	7
	8	#define CONFIG_BAUDRATE 57600
	9	#define CONFIG_STAMP 1
	10
	11	#define CONFIG_BOOTDELAY 5
8db13d63	12	#define CFG_AUTOLOAD "no" /rarpb, bootp or dhcp commands will perform only a /
3f0606ad	13
8db13d63	14	#define CFG_LONGHELP 1
3f0606ad	15	#define CONFIG_CMDLINE_EDITING 1
8db13d63	16	#define CONFIG_LOADADDR 0x01000000 /* default load address */
3f0606ad	17	#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux"
8db13d63	18	/* #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" */
3f0606ad AL	19
	20	#define CONFIG_DRIVER_SMC91111 1
	21	#define CONFIG_SMC91111_BASE 0x20310300
	22
	23	#if 0
	24	#define CONFIG_MII
	25	#define CFG_DISCOVER_PHY
	26	#endif
	27
	28	#define CONFIG_RTC_BFIN 1
	29	#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
	30
	31	/*
	32	* Boot Mode Set
	33	* Blackfin can support several boot modes
	34	*/
8db13d63 AL	35	#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
	36	#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
	37	#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
3f0606ad AL	38	/* Define the boot mode */
3f0606ad AL	39	#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
8db13d63	40	/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
3f0606ad AL	41
	42	#define CONFIG_PANIC_HANG 1
	43
	44	#define ADSP_BF531 0x31
	45	#define ADSP_BF532 0x32
	46	#define ADSP_BF533 0x33
	47	#define BFIN_CPU ADSP_BF533
	48
	49	/* This sets the default state of the cache on U-Boot's boot */
	50	#define CONFIG_ICACHE_ON
	51	#define CONFIG_DCACHE_ON
	52
	53	/* Define where the uboot will be loaded by on-chip boot rom */
	54	#define APP_ENTRY 0x00001000
	55
8db13d63 AL	56	/* CONFIG_CLKIN_HZ is any value in Hz */
	57	#define CONFIG_CLKIN_HZ 27000000
	58	/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
	59	/* 1=CLKIN/2 */
	60	#define CONFIG_CLKIN_HALF 0
	61	/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
	62	/* 1=bypass PLL */
	63	#define CONFIG_PLL_BYPASS 0
	64	/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
	65	/* Values can range from 1-64 */
	66	#define CONFIG_VCO_MULT 22
	67	/* CONFIG_CCLK_DIV controls what the core clock divider is */
	68	/* Values can be 1, 2, 4, or 8 ONLY */
	69	#define CONFIG_CCLK_DIV 1
3f0606ad	70	/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
8db13d63 AL	71	/* Values can range from 1-15 */
	72	#define CONFIG_SCLK_DIV 5
	73	/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
	74	/* Values can range from 2-65535 */
	75	/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
	76	#define CONFIG_SPI_BAUD 2
	77	#define CONFIG_SPI_BAUD_INITBLOCK 4
3f0606ad AL	78
3f0606ad AL	79	#if ( CONFIG_CLKIN_HALF == 0 )
8db13d63	80	#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
3f0606ad	81	#else
8db13d63	82	#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
3f0606ad AL	83	#endif
	84
	85	#if (CONFIG_PLL_BYPASS == 0)
8db13d63 AL	86	#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
8db13d63 AL	87	#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
3f0606ad	88	#else
8db13d63 AL	89	#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
8db13d63 AL	90	#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
3f0606ad AL	91	#endif
3f0606ad AL	92
8440bb14	93	#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */
8db13d63 AL	94	#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
8db13d63 AL	95	#define CONFIG_MEM_MT48LC16M16A2TG_75 1
3f0606ad AL	96
	97	#define CONFIG_LOADS_ECHO 1
	98
	99
079a136c JL	100	/*
	101	* BOOTP options
	102	*/
	103	#define CONFIG_BOOTP_BOOTFILESIZE
	104	#define CONFIG_BOOTP_BOOTPATH
	105	#define CONFIG_BOOTP_GATEWAY
	106	#define CONFIG_BOOTP_HOSTNAME
	107
	108
ba2351f9 JL	109	/*
	110	* Command line configuration.
	111	*/
	112	#include <config_cmd_default.h>
3f0606ad	113
ba2351f9 JL	114	#define CONFIG_CMD_PING
	115	#define CONFIG_CMD_ELF
	116	#define CONFIG_CMD_I2C
	117	#define CONFIG_CMD_JFFS2
	118	#define CONFIG_CMD_DATE
	119
	120
	121	#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"
3f0606ad AL	122
3f0606ad AL	123	#define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */
ba2351f9	124	#if defined(CONFIG_CMD_KGDB)
3f0606ad AL	125	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
	126	#else
	127	#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
	128	#endif
	129	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	130	#define CFG_MAXARGS 16 /* max number of command args */
	131	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
	132	#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
	133	#define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */
	134	#define CFG_LOAD_ADDR 0x01000000 /* default load address */
	135	#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */
	136	#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
	137	#define CFG_SDRAM_BASE 0x00000000
	138	#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
	139	#define CFG_FLASH_BASE 0x20000000
	140
	141	#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	142	#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
	143	#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
	144	#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
	145	#define CFG_GBL_DATA_SIZE 0x4000
	146	#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
	147	#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
	148
	149	#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
	150	#define CFG_FLASH0_BASE 0x20000000
	151	#define CFG_FLASH1_BASE 0x20200000
	152	#define CFG_FLASH2_BASE 0x20280000
	153	#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
	154	#define CFG_MAX_FLASH_SECT 40 /* max number of sectors on one chip */
	155
	156	#define CFG_ENV_IS_IN_FLASH 1
	157	#define CFG_ENV_ADDR 0x20020000
	158	#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
	159
	160	/* JFFS Partition offset set */
8db13d63 AL	161	#define CFG_JFFS2_FIRST_BANK 0
8db13d63 AL	162	#define CFG_JFFS2_NUM_BANKS 1
3f0606ad	163	/* 512k reserved for u-boot */
8db13d63	164	#define CFG_JFFS2_FIRST_SECTOR 11
3f0606ad AL	165
	166
	167	/*
	168	* Stack sizes
	169	*/
8db13d63	170	#define CONFIG_STACKSIZE (1281024) / regular stack */
3f0606ad AL	171
	172	#define POLL_MODE 1
	173	#define FLASH_TOT_SECT 40
	174	#define FLASH_SIZE 0x220000
	175	#define CFG_FLASH_SIZE 0x220000
	176
	177	/*
	178	* Initialize PSD4256 registers for using I2C
	179	*/
	180	#define CONFIG_MISC_INIT_R
	181
	182	/*
	183	* I2C settings
	184	* By default PF1 is used as SDA and PF0 as SCL on the Stamp board
	185	*/
8db13d63	186	#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
3f0606ad AL	187	/*
	188	* Software (bit-bang) I2C driver configuration
	189	*/
8db13d63 AL	190	#define PF_SCL PF0
	191	#define PF_SDA PF1
	192
	193	#define I2C_INIT (*pFIO_DIR \|= PF_SCL); asm("ssync;")
	194	#define I2C_ACTIVE (pFIO_DIR \|= PF_SDA); pFIO_INEN &= ~PF_SDA; asm("ssync;")
	195	#define I2C_TRISTATE (pFIO_DIR &= ~PF_SDA); pFIO_INEN \|= PF_SDA; asm("ssync;")
	196	#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
	197	#define I2C_SDA(bit) if(bit) { \
	198	*pFIO_FLAG_S = PF_SDA; \
	199	asm("ssync;"); \
	200	} \
	201	else { \
	202	*pFIO_FLAG_C = PF_SDA; \
	203	asm("ssync;"); \
	204	}
	205	#define I2C_SCL(bit) if(bit) { \
	206	*pFIO_FLAG_S = PF_SCL; \
	207	asm("ssync;"); \
	208	} \
	209	else { \
	210	*pFIO_FLAG_C = PF_SCL; \
	211	asm("ssync;"); \
	212	}
	213	#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
	214
	215	#define CFG_I2C_SPEED 50000
	216	#define CFG_I2C_SLAVE 0xFE
3f0606ad AL	217
	218	#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
	219
	220	/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
8db13d63 AL	221	/* #define AMGCTLVAL (AMBEN_P0 \| AMBEN_P1 \| AMBEN_P2 \| AMCKEN)
	222	#define AMBCTL0VAL (B1WAT_7 \| B1RAT_11 \| B1HT_2 \| B1ST_3 \| B1TT_4 \| ~B1RDYPOL \| \
	223	~B1RDYEN \| B0WAT_7 \| B0RAT_11 \| B0HT_2 \| B0ST_3 \| B0TT_4 \| ~B0RDYPOL \| ~B0RDYEN)
	224	#define AMBCTL1VAL (B3WAT_2 \| B3RAT_2 \| B3HT_1 \| B3ST_1 \| B3TT_4 \| B3RDYPOL \| ~B3RDYEN \| \
	225	B2WAT_7 \| B2RAT_11 \| B2HT_2 \| B2ST_3 \| B2TT_4 \| ~B2RDYPOL \| ~B2RDYEN)
3f0606ad	226	*/
8db13d63 AL	227	#define AMGCTLVAL 0xFF
	228	#define AMBCTL0VAL 0x7BB07BB0
	229	#define AMBCTL1VAL 0xFFC27BB0
3f0606ad AL	230
	231	#define CONFIG_VDSP 1
	232
	233	#ifdef CONFIG_VDSP
	234	#define ET_EXEC_VDSP 0x8
	235	#define SHT_STRTAB_VDSP 0x1
	236	#define ELFSHDRSIZE_VDSP 0x2C
	237	#define VDSP_ENTRY_ADDR 0xFFA00000
	238	#endif
	239
	240	#endif