[J-u-boot.git] / include / configs / vinco.h

/*
 * Configuration settings for the VInCo platform.
 *
 * Based on the settings for the SAMA5-EK board
 * Copyright (C) 2014 Atmel
 *		      Bo Shen <[email protected]>
 * Copyright (C) 2015 Free Electrons
 *		      Gregory CLEMENT [email protected]
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/* No NOR flash, this definition should be put before common header */
#define CONFIG_SYS_NO_FLASH

#include "at91-sama5_common.h"

/* The value in the common file is too far away for the VInCo platform */
#ifdef CONFIG_SYS_TEXT_BASE
#undef CONFIG_SYS_TEXT_BASE
#endif
#define CONFIG_SYS_TEXT_BASE		0x20f00000

/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE		ATMEL_BASE_USART3
#define	CONFIG_USART_ID			ATMEL_ID_USART3

/* SDRAM */
#define CONFIG_NR_DRAM_BANKS		1
#define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
#define CONFIG_SYS_SDRAM_SIZE		0x4000000

#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)

#define CONFIG_SYS_LOAD_ADDR		0x22000000 /* load address */

/* SerialFlash */

#ifdef CONFIG_CMD_SF
#define CONFIG_ATMEL_SPI
#define CONFIG_ATMEL_SPI0
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_SF_DEFAULT_BUS		0
#define CONFIG_SF_DEFAULT_CS		0
#define CONFIG_SF_DEFAULT_SPEED		50000000
#define CONFIG_ENV_SPI_MAX_HZ		50000000
#define CONFIG_SF_DEFAULT_MODE		(SPI_MODE_0)
#define CONFIG_ENV_SPI_MODE		(SPI_MODE_0)
#endif

/* MMC */

#ifdef CONFIG_CMD_MMC
#define CONFIG_SUPPORT_EMMC_BOOT
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_GENERIC_ATMEL_MCI
#define ATMEL_BASE_MMCI			ATMEL_BASE_MCI1
#define CONFIG_SYS_MMC_CLK_OD		500000

/* For generating MMC partitions */
#define CONFIG_PARTITION_UUIDS
#define CONFIG_RANDOM_UUID
#define CONFIG_EFI_PARTITION
#define CONFIG_CMD_GPT

#endif

/* USB */

#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
#define CONFIG_USB_STORAGE
#endif

/* USB device */
#define CONFIG_USB_ETHER
#define CONFIG_USB_ETH_RNDIS
#define CONFIG_USBNET_MANUFACTURER      "L+G VInCo"

#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_DOS_PARTITION
#endif

/* Ethernet Hardware */
#define CONFIG_PHY_SMSC
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT		20
#define CONFIG_MACB_SEARCH_PHY

#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_USB_ETHER_RNDIS

#ifdef CONFIG_SYS_USE_SERIALFLASH
/* bootstrap + u-boot + env + linux in serial flash */
#define CONFIG_ENV_SPI_BUS	CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS	CONFIG_SF_DEFAULT_CS
/* Use our own mapping for the VInCo platform */
#undef CONFIG_ENV_OFFSET
#undef CONFIG_ENV_SIZE

#define CONFIG_ENV_OFFSET       0x10000
#define CONFIG_ENV_SIZE         0x10000

/* Update the bootcommand according to our mapping for the VInCo platform */
#undef CONFIG_BOOTCOMMAND
#define CONFIG_BOOTCOMMAND  "mmc dev 0 0;" \
			    "mmc read ${loadaddr} ${k_offset} ${k_blksize};" \
			    "mmc read ${oftaddr} ${dtb_offset} ${dtb_blksize};" \
			    "bootz ${loadaddr} -  ${oftaddr}"

#undef CONFIG_BOOTARGS
#define CONFIG_BOOTARGS	    "console=ttyS0,115200 earlyprintk rw root=/dev/mmcblk0p2 rootfstype=ext4 rootwait quiet lpj=1990656"

#define CONFIG_EXTRA_ENV_SETTINGS \
	"kernel_start=0x20000\0" \
	"kernel_size=0x800000\0" \
	"mmcblksize=0x200\0" \
	"oftaddr=0x21000000\0" \
	"loadaddr=0x22000000\0" \
	"update_uboot=tftp ${loadaddr} u-boot.bin;sf probe 0;" \
	"sf erase 0x20000 0x4B000; sf write ${loadaddr} 0x20000 0x4B000\0" \
	"create_partition=setexpr dtb_start ${kernel_start} + 0x400000;" \
	"setexpr rootfs_start ${kernel_start} + ${kernel_size};" \
	"setenv partitions 'name=kernel,size=${kernel_size}," \
	"start=${kernel_start};name=rootfs,size=-';" \
	"gpt write mmc 0 ${partitions} \0"\
	"f2blk_size=setexpr fileblksize ${filesize} / ${mmcblksize};" \
	"setexpr fileblksize ${fileblksize} + 1\0" \
	"store_kernel=tftp ${loadaddr} zImage; run f2blk_size;" \
	"setexpr k_blksize ${fileblksize};" \
	"setexpr k_offset ${kernel_start} / ${mmcblksize};" \
	"mmc write ${fileaddr} ${k_offset} ${fileblksize}\0" \
	"store_dtb=tftp ${loadaddr} at91-vinco.dtb; run f2blk_size;" \
	"setexpr dtb_blksize ${fileblksize};" \
	"setexpr dtb_offset ${dtb_start} / ${mmcblksize};" \
	"mmc write ${fileaddr} ${dtb_offset} ${fileblksize}\0" \
	"store_rootfs=tftp ${loadaddr} vinco-gateway-image-vinco.ext4;" \
	"setexpr rootfs_offset ${rootfs_start} / ${mmcblksize};" \
	"mmc write ${fileaddr} ${rootfs_offset} ${fileblksize}\0" \
	"bootdelay=0\0"

#endif
#define CONFIG_ZERO_BOOTDELAY_CHECK

#endif
Commit	Line	Data
522e4fbb GC	1	/*
	2	* Configuration settings for the VInCo platform.
	3	*
	4	* Based on the settings for the SAMA5-EK board
	5	* Copyright (C) 2014 Atmel
	6	* Bo Shen <[email protected]>
	7	* Copyright (C) 2015 Free Electrons
	8	* Gregory CLEMENT [email protected]
	9	*
	10	* SPDX-License-Identifier: GPL-2.0+
	11	*/
	12
	13	#ifndef __CONFIG_H
	14	#define __CONFIG_H
	15
	16	/* No NOR flash, this definition should be put before common header */
	17	#define CONFIG_SYS_NO_FLASH
	18
	19	#include "at91-sama5_common.h"
	20
	21	/* The value in the common file is too far away for the VInCo platform */
	22	#ifdef CONFIG_SYS_TEXT_BASE
	23	#undef CONFIG_SYS_TEXT_BASE
	24	#endif
	25	#define CONFIG_SYS_TEXT_BASE 0x20f00000
	26
	27	/* serial console */
	28	#define CONFIG_ATMEL_USART
	29	#define CONFIG_USART_BASE ATMEL_BASE_USART3
	30	#define CONFIG_USART_ID ATMEL_ID_USART3
	31
	32	/* SDRAM */
	33	#define CONFIG_NR_DRAM_BANKS 1
	34	#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
	35	#define CONFIG_SYS_SDRAM_SIZE 0x4000000
	36
522e4fbb GC	37	#define CONFIG_SYS_INIT_SP_ADDR \
	38	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
	39
	40	#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
	41
	42	/* SerialFlash */
522e4fbb GC	43
	44	#ifdef CONFIG_CMD_SF
	45	#define CONFIG_ATMEL_SPI
	46	#define CONFIG_ATMEL_SPI0
	47	#define CONFIG_SPI_FLASH_STMICRO
	48	#define CONFIG_SF_DEFAULT_BUS 0
	49	#define CONFIG_SF_DEFAULT_CS 0
	50	#define CONFIG_SF_DEFAULT_SPEED 50000000
	51	#define CONFIG_ENV_SPI_MAX_HZ 50000000
	52	#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
	53	#define CONFIG_ENV_SPI_MODE (SPI_MODE_0)
	54	#endif
	55
522e4fbb	56	/* MMC */
522e4fbb GC	57
	58	#ifdef CONFIG_CMD_MMC
	59	#define CONFIG_SUPPORT_EMMC_BOOT
	60	#define CONFIG_MMC
	61	#define CONFIG_GENERIC_MMC
	62	#define CONFIG_GENERIC_ATMEL_MCI
	63	#define ATMEL_BASE_MMCI ATMEL_BASE_MCI1
	64	#define CONFIG_SYS_MMC_CLK_OD 500000
	65
	66	/* For generating MMC partitions */
	67	#define CONFIG_PARTITION_UUIDS
	68	#define CONFIG_RANDOM_UUID
	69	#define CONFIG_EFI_PARTITION
	70	#define CONFIG_CMD_GPT
	71
	72	#endif
	73
	74	/* USB */
522e4fbb GC	75
	76	#ifdef CONFIG_CMD_USB
	77	#define CONFIG_USB_EHCI
	78	#define CONFIG_USB_EHCI_ATMEL
	79	#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
	80	#define CONFIG_USB_STORAGE
	81	#endif
	82
	83	/* USB device */
522e4fbb GC	84	#define CONFIG_USB_ETHER
	85	#define CONFIG_USB_ETH_RNDIS
	86	#define CONFIG_USBNET_MANUFACTURER "L+G VInCo"
	87
	88	#if defined(CONFIG_CMD_USB) \|\| defined(CONFIG_CMD_MMC)
522e4fbb GC	89	#define CONFIG_DOS_PARTITION
	90	#endif
	91
	92	/* Ethernet Hardware */
522e4fbb GC	93	#define CONFIG_PHY_SMSC
	94	#define CONFIG_MACB
	95	#define CONFIG_RMII
	96	#define CONFIG_NET_RETRY_COUNT 20
	97	#define CONFIG_MACB_SEARCH_PHY
	98
522e4fbb GC	99	#define CONFIG_USB_HOST_ETHER
	100	#define CONFIG_USB_ETHER_SMSC95XX
	101	#define CONFIG_USB_ETHER_RNDIS
	102
522e4fbb GC	103	#ifdef CONFIG_SYS_USE_SERIALFLASH
	104	/* bootstrap + u-boot + env + linux in serial flash */
	105	#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
	106	#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
	107	/* Use our own mapping for the VInCo platform */
	108	#undef CONFIG_ENV_OFFSET
	109	#undef CONFIG_ENV_SIZE
	110
	111	#define CONFIG_ENV_OFFSET 0x10000
	112	#define CONFIG_ENV_SIZE 0x10000
	113
	114	/* Update the bootcommand according to our mapping for the VInCo platform */
	115	#undef CONFIG_BOOTCOMMAND
	116	#define CONFIG_BOOTCOMMAND "mmc dev 0 0;" \
	117	"mmc read ${loadaddr} ${k_offset} ${k_blksize};" \
	118	"mmc read ${oftaddr} ${dtb_offset} ${dtb_blksize};" \
	119	"bootz ${loadaddr} - ${oftaddr}"
	120
	121	#undef CONFIG_BOOTARGS
	122	#define CONFIG_BOOTARGS "console=ttyS0,115200 earlyprintk rw root=/dev/mmcblk0p2 rootfstype=ext4 rootwait quiet lpj=1990656"
	123
	124	#define CONFIG_EXTRA_ENV_SETTINGS \
	125	"kernel_start=0x20000\0" \
	126	"kernel_size=0x800000\0" \
	127	"mmcblksize=0x200\0" \
	128	"oftaddr=0x21000000\0" \
	129	"loadaddr=0x22000000\0" \
	130	"update_uboot=tftp ${loadaddr} u-boot.bin;sf probe 0;" \
	131	"sf erase 0x20000 0x4B000; sf write ${loadaddr} 0x20000 0x4B000\0" \
	132	"create_partition=setexpr dtb_start ${kernel_start} + 0x400000;" \
	133	"setexpr rootfs_start ${kernel_start} + ${kernel_size};" \
	134	"setenv partitions 'name=kernel,size=${kernel_size}," \
	135	"start=${kernel_start};name=rootfs,size=-';" \
	136	"gpt write mmc 0 ${partitions} \0"\
	137	"f2blk_size=setexpr fileblksize ${filesize} / ${mmcblksize};" \
	138	"setexpr fileblksize ${fileblksize} + 1\0" \
	139	"store_kernel=tftp ${loadaddr} zImage; run f2blk_size;" \
	140	"setexpr k_blksize ${fileblksize};" \
	141	"setexpr k_offset ${kernel_start} / ${mmcblksize};" \
	142	"mmc write ${fileaddr} ${k_offset} ${fileblksize}\0" \
	143	"store_dtb=tftp ${loadaddr} at91-vinco.dtb; run f2blk_size;" \
	144	"setexpr dtb_blksize ${fileblksize};" \
	145	"setexpr dtb_offset ${dtb_start} / ${mmcblksize};" \
	146	"mmc write ${fileaddr} ${dtb_offset} ${fileblksize}\0" \
	147	"store_rootfs=tftp ${loadaddr} vinco-gateway-image-vinco.ext4;" \
	148	"setexpr rootfs_offset ${rootfs_start} / ${mmcblksize};" \
	149	"mmc write ${fileaddr} ${rootfs_offset} ${fileblksize}\0" \
	150	"bootdelay=0\0"
	151
	152	#endif
	153	#define CONFIG_ZERO_BOOTDELAY_CHECK
	154
	155	#endif