[J-u-boot.git] / include / configs / tqma6.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright (C) 2013, 2014, 2017 Markus Niebel <[email protected]>
 *
 * Configuration settings for the TQ Systems TQMa6<Q,D,DL,S> module.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include <linux/kconfig.h>
#include <linux/stringify.h>

/* SPL */
/* #if defined(CONFIG_SPL_BUILD) */
/* common IMX6 SPL configuration */
#include "imx6_spl.h"

/* #endif */

/* place code in last 4 MiB of RAM */

#include "mx6_common.h"

#if defined(CONFIG_TQMA6S)
#define PHYS_SDRAM_SIZE			(512u * SZ_1M)
#elif defined(CONFIG_TQMA6DL)
#define PHYS_SDRAM_SIZE			(SZ_1G)
#elif defined(CONFIG_TQMA6Q)
#define PHYS_SDRAM_SIZE			(SZ_1G)
#endif

/* SPI Flash */

#define TQMA6_SPI_FLASH_SECTOR_SIZE	SZ_64K

/* I2C Configs */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED		100000

/* I2C EEPROM (M24C64) */
#define CONFIG_SYS_I2C_EEPROM_ADDR			0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN			2
#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS		5 /* 32 Bytes */
#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS	20

#if !defined(CONFIG_DM_PMIC)
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
#define TQMA6_PFUZE100_I2C_BUS		2
#endif

/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR	0

/* USB Configs */
#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */

#define CONFIG_FEC_MXC
#define IMX_FEC_BASE			ENET_BASE_ADDR

#define CONFIG_ARP_TIMEOUT		200UL

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2 * SZ_1M)

#if defined(CONFIG_TQMA6X_MMC_BOOT)

#define TQMA6_UBOOT_OFFSET		SZ_1K
#define TQMA6_UBOOT_SECTOR_START	0x2
#define TQMA6_UBOOT_SECTOR_COUNT	0x7fe

#define CONFIG_SYS_MMC_ENV_DEV		0

#define TQMA6_FDT_OFFSET		(2 * SZ_1M)
#define TQMA6_FDT_SECTOR_START		0x1000
#define TQMA6_FDT_SECTOR_COUNT		0x800

#define TQMA6_KERNEL_SECTOR_START	0x2000
#define TQMA6_KERNEL_SECTOR_COUNT	0x2000

#define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
	"uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0"                \
	"uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"                 \
	"fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
	"fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                     \
	"kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
	"kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"               \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0"                       \
	"loadimage=mmc dev ${mmcdev}; "                                        \
		"mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0"       \
	"loadfdt=mmc dev ${mmcdev}; "                                          \
		"mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0"             \
	"update_uboot=if tftp ${uboot}; then "                                 \
		"if itest ${filesize} > 0; then "                              \
			"mmc dev ${mmcdev}; mmc rescan; "                      \
			"setexpr blkc ${filesize} + 0x1ff; "                   \
			"setexpr blkc ${blkc} / 0x200; "                       \
			"if itest ${blkc} <= ${uboot_size}; then "             \
				"mmc write ${loadaddr} ${uboot_start} "        \
					"${blkc}; "                            \
			"fi; "                                                 \
		"fi; fi; "                                                     \
		"setenv filesize; setenv blkc \0"                              \
	"update_kernel=run kernel_name; "                                      \
		"if tftp ${kernel}; then "                                     \
			"if itest ${filesize} > 0; then "                      \
				"mmc dev ${mmcdev}; mmc rescan; "              \
				"setexpr blkc ${filesize} + 0x1ff; "           \
				"setexpr blkc ${blkc} / 0x200; "               \
				"if itest ${blkc} <= ${kernel_size}; then "    \
					"mmc write ${loadaddr} "               \
						"${kernel_start} ${blkc}; "    \
				"fi; "                                         \
			"fi; "                                                 \
		"fi; "                                                         \
		"setenv filesize; setenv blkc \0"                              \
	"update_fdt=if tftp ${fdt_file}; then "                                \
		"if itest ${filesize} > 0; then "                              \
			"mmc dev ${mmcdev}; mmc rescan; "                      \
			"setexpr blkc ${filesize} + 0x1ff; "                   \
			"setexpr blkc ${blkc} / 0x200; "                       \
			"if itest ${blkc} <= ${fdt_size}; then "               \
				"mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
			"fi; "                                                 \
		"fi; fi; "                                                     \
		"setenv filesize; setenv blkc \0"                              \

#define CONFIG_BOOTCOMMAND \
	"run mmcboot; run netboot; run panicboot"

#elif defined(CONFIG_TQMA6X_SPI_BOOT)

#define TQMA6_UBOOT_OFFSET		0x400
#define TQMA6_UBOOT_SECTOR_START	0x0
/* max u-boot size: 512k */
#define TQMA6_UBOOT_SECTOR_SIZE		TQMA6_SPI_FLASH_SECTOR_SIZE
#define TQMA6_UBOOT_SECTOR_COUNT	0x8
#define TQMA6_UBOOT_SIZE		(TQMA6_UBOOT_SECTOR_SIZE * \
					 TQMA6_UBOOT_SECTOR_COUNT)

#define TQMA6_FDT_OFFSET		(CONFIG_ENV_OFFSET_REDUND + \
					 CONFIG_ENV_SECT_SIZE)
#define TQMA6_FDT_SECT_SIZE		(TQMA6_SPI_FLASH_SECTOR_SIZE)

#define TQMA6_FDT_SECTOR_START		0x0a /* 8 Sector u-boot, 2 Sector env */
#define TQMA6_FDT_SECTOR_COUNT		0x01

#define TQMA6_KERNEL_SECTOR_START	0x10
#define TQMA6_KERNEL_SECTOR_COUNT	0x60

#define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
	"mmcblkdev=0\0"                                                        \
	"uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0"                     \
	"uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"              \
	"fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
	"fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                  \
	"kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
	"kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"            \
	"update_uboot=if tftp ${uboot}; then "                                 \
		"if itest ${filesize} > 0; then "                              \
			"setexpr blkc ${filesize} + "                          \
				__stringify(TQMA6_UBOOT_OFFSET) "; "           \
			"setexpr size ${uboot_sectors} * "                     \
				__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
			"if itest ${blkc} <= ${size}; then "                   \
				"sf probe; "                                   \
				"sf erase 0 ${size}; "                         \
				"sf write ${loadaddr} ${uboot_offset} "        \
					"${filesize}; "                        \
			"fi; "                                                 \
		"fi; fi; "                                                     \
		"setenv filesize 0; setenv blkc; setenv size \0"               \
	"update_kernel=run kernel_name; if tftp ${kernel}; then "              \
		"if itest ${filesize} > 0; then "                              \
			"setexpr size ${kernel_sectors} * "                    \
				__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
			"setexpr offset ${kernel_start} * "                    \
				__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
			"if itest ${filesize} <= ${size}; then "               \
				"sf probe; "                                   \
				"sf erase ${offset} ${size}; "                 \
				"sf write ${loadaddr} ${offset} "              \
					"${filesize}; "                        \
			"fi; "                                                 \
		"fi; fi; "                                                     \
		"setenv filesize 0; setenv size ; setenv offset\0"             \
	"update_fdt=if tftp ${fdt_file}; then "                                \
		"if itest ${filesize} > 0; then "                              \
			"setexpr size ${fdt_sectors} * "                       \
				__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
			"setexpr offset ${fdt_start} * "                       \
				__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
			"if itest ${filesize} <= ${size}; then "               \
				"sf probe; "                                   \
				"sf erase ${offset} ${size}; "                 \
				"sf write ${loadaddr} ${offset} "              \
					"${filesize}; "                        \
			"fi; "                                                 \
		"fi; fi; "                                                     \
		"setenv filesize 0; setenv size ; setenv offset\0"             \
	"loadimage=sf probe; "                                                 \
		"setexpr size ${kernel_sectors} * "                            \
			__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
		"setexpr offset ${kernel_start} * "                            \
			__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
		"sf read ${loadaddr} ${offset} ${size}; "                      \
		"setenv size ; setenv offset\0"                                \
	"loadfdt=sf probe; "                                                   \
		"setexpr size ${fdt_sectors} * "                               \
			__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
		"setexpr offset ${fdt_start} * "                               \
			__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
		"sf read ${fdt_addr} ${offset} ${size}; "                      \
		"setenv size ; setenv offset\0"                                \

#define CONFIG_BOOTCOMMAND                                                     \
	"sf probe; run mmcboot; run netboot; run panicboot"                    \

#else

#error "need to define boot source"

#endif

/* 128 MiB offset as in ARM related docu for linux suggested */
#define TQMA6_FDT_ADDRESS		0x18000000

/* set to a resonable value, changeable by user */
#define TQMA6_CMA_SIZE                 160M

#define CONFIG_EXTRA_ENV_SETTINGS                                              \
	"board=tqma6\0"                                                        \
	"uimage=uImage\0"                                                      \
	"zimage=zImage\0"                                                      \
	"boot_type=bootz\0"                                                    \
	"kernel_name=if test \"${boot_type}\" != bootz; then "                 \
		"setenv kernel ${uimage}; "                                    \
		"else setenv kernel ${zimage}; fi\0"                           \
	"uboot=u-boot.imx\0"                                                   \
	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0"                               \
	"fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0"                          \
	"console=" CONSOLE_DEV "\0"                                            \
	"cma_size="__stringify(TQMA6_CMA_SIZE)"\0"                             \
	"fdt_high=0xffffffff\0"                                                \
	"initrd_high=0xffffffff\0"                                             \
	"rootfsmode=ro\0"                                                      \
	"addcma=setenv bootargs ${bootargs} cma=${cma_size}\0"                 \
	"addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0"  \
	"addfb=setenv bootargs ${bootargs} "                                   \
		"imx-fbdev.legacyfb_depth=32 consoleblank=0\0"                 \
	"mmcpart=2\0"                                                          \
	"mmcblkdev=0\0"                                                        \
	"mmcargs=run addmmc addtty addfb addcma\0"                             \
	"addmmc=setenv bootargs ${bootargs} "                                  \
		"root=/dev/mmcblk${mmcblkdev}p${mmcpart} ${rootfsmode} "       \
		"rootwait\0"                                                   \
	"mmcboot=echo Booting from mmc ...; "                                  \
		"setenv bootargs; "                                            \
		"run mmcargs; "                                                \
		"run loadimage; "                                              \
		"if run loadfdt; then "                                        \
			"echo boot device tree kernel ...; "                   \
			"${boot_type} ${loadaddr} - ${fdt_addr}; "             \
		"else "                                                        \
			"${boot_type}; "                                       \
		"fi;\0"                                                        \
		"setenv bootargs \0"                                           \
	"netdev=eth0\0"                                                        \
	"rootpath=/srv/nfs/tqma6\0"                                            \
	"ipmode=static\0"                                                      \
	"netargs=run addnfs addip addtty addfb addcma\0"                       \
	"addnfs=setenv bootargs ${bootargs} "                                  \
		"root=/dev/nfs rw "                                            \
		"nfsroot=${serverip}:${rootpath},v3,tcp;\0"                    \
	"addip_static=setenv bootargs ${bootargs} "                            \
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:"            \
		"${hostname}:${netdev}:off\0"                                  \
	"addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0"                  \
	"addip=if test \"${ipmode}\" != static; then "                         \
		"run addip_dynamic; else run addip_static; fi\0"               \
	"set_getcmd=if test \"${ipmode}\" != static; then "                    \
		"setenv getcmd dhcp; setenv autoload yes; "                    \
		"else setenv getcmd tftp; setenv autoload no; fi\0"            \
	"netboot=echo Booting from net ...; "                                  \
		"run kernel_name; "                                            \
		"run set_getcmd; "                                             \
		"setenv bootargs; "                                            \
		"run netargs; "                                                \
		"if ${getcmd} ${kernel}; then "                                \
			"if ${getcmd} ${fdt_addr} ${fdt_file}; then "          \
				"${boot_type} ${loadaddr} - ${fdt_addr}; "     \
			"fi; "                                                 \
		"fi; "                                                         \
		"echo ... failed\0"                                            \
	"panicboot=echo No boot device !!! reset\0"                            \
	TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                      \

/* Physical Memory Map */
#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/*
 * All the defines above are for the TQMa6 SoM
 *
 * Now include the baseboard specific configuration
 */
#ifdef CONFIG_MBA6
#include "tqma6_mba6.h"
#elif CONFIG_WRU4
#include "tqma6_wru4.h"
#else
#error "No baseboard for the TQMa6 defined!"
#endif

/* Support at least the sensor on TQMa6 SOM */

#endif /* __CONFIG_H */
Commit	Line	Data
83d290c5	1	/* SPDX-License-Identifier: GPL-2.0+ */
cb07d74e	2	/*
468fb1e4	3	* Copyright (C) 2013, 2014, 2017 Markus Niebel <[email protected]>
cb07d74e	4	*
468fb1e4	5	* Configuration settings for the TQ Systems TQMa6<Q,D,DL,S> module.
cb07d74e MN	6	*/
	7
	8	#ifndef __CONFIG_H
	9	#define __CONFIG_H
	10
66cacc9d	11	#include <linux/kconfig.h>
1af3c7f4 SG	12	#include <linux/stringify.h>
1af3c7f4 SG	13
1719d49c MN	14	/* SPL */
1719d49c MN	15	/* #if defined(CONFIG_SPL_BUILD) */
1719d49c MN	16	/* common IMX6 SPL configuration */
	17	#include "imx6_spl.h"
	18
	19	/* #endif */
	20
cd6ddc48	21	/* place code in last 4 MiB of RAM */
cd6ddc48	22
cb07d74e	23	#include "mx6_common.h"
cb07d74e	24
d4b349e4	25	#if defined(CONFIG_TQMA6S)
cb07d74e	26	#define PHYS_SDRAM_SIZE (512u * SZ_1M)
468fb1e4 MN	27	#elif defined(CONFIG_TQMA6DL)
468fb1e4 MN	28	#define PHYS_SDRAM_SIZE (SZ_1G)
d4b349e4	29	#elif defined(CONFIG_TQMA6Q)
468fb1e4	30	#define PHYS_SDRAM_SIZE (SZ_1G)
cb07d74e MN	31	#endif
cb07d74e MN	32
cb07d74e	33	/* SPI Flash */
cb07d74e	34
52835468 MN	35	#define TQMA6_SPI_FLASH_SECTOR_SIZE SZ_64K
52835468 MN	36
cb07d74e	37	/* I2C Configs */
cb07d74e MN	38	#define CONFIG_I2C_MULTI_BUS
	39	#define CONFIG_SYS_I2C_SPEED 100000
	40
cb07d74e MN	41	/* I2C EEPROM (M24C64) */
	42	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	43	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	44	#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS 5 /* 32 Bytes */
	45	#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS 20
cb07d74e	46
e7ae6b5e	47	#if !defined(CONFIG_DM_PMIC)
cb07d74e MN	48	#define CONFIG_POWER
	49	#define CONFIG_POWER_I2C
	50	#define CONFIG_POWER_PFUZE100
	51	#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
	52	#define TQMA6_PFUZE100_I2C_BUS 2
e7ae6b5e	53	#endif
cb07d74e MN	54
cb07d74e MN	55	/* MMC Configs */
cb07d74e MN	56	#define CONFIG_SYS_FSL_ESDHC_ADDR 0
cb07d74e MN	57
cb07d74e	58	/* USB Configs */
cb07d74e	59	#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI \| PORT_PTS_PTW)
911b5ea5 SR	60	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
911b5ea5 SR	61	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
cb07d74e	62
cb07d74e MN	63	#define CONFIG_FEC_MXC
cb07d74e MN	64	#define IMX_FEC_BASE ENET_BASE_ADDR
cb07d74e	65
cb07d74e	66	#define CONFIG_ARP_TIMEOUT 200UL
cb07d74e	67
cb07d74e MN	68	/* Size of malloc() pool */
	69	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * SZ_1M)
	70
	71	#if defined(CONFIG_TQMA6X_MMC_BOOT)
	72
cb07d74e MN	73	#define TQMA6_UBOOT_OFFSET SZ_1K
	74	#define TQMA6_UBOOT_SECTOR_START 0x2
	75	#define TQMA6_UBOOT_SECTOR_COUNT 0x7fe
	76
cb07d74e MN	77	#define CONFIG_SYS_MMC_ENV_DEV 0
	78
	79	#define TQMA6_FDT_OFFSET (2 * SZ_1M)
	80	#define TQMA6_FDT_SECTOR_START 0x1000
	81	#define TQMA6_FDT_SECTOR_COUNT 0x800
	82
	83	#define TQMA6_KERNEL_SECTOR_START 0x2000
	84	#define TQMA6_KERNEL_SECTOR_COUNT 0x2000
	85
	86	#define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
	87	"uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0" \
	88	"uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0" \
	89	"fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0" \
	90	"fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0" \
	91	"kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0" \
	92	"kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0" \
	93	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	94	"loadimage=mmc dev ${mmcdev}; " \
	95	"mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0" \
	96	"loadfdt=mmc dev ${mmcdev}; " \
	97	"mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0" \
	98	"update_uboot=if tftp ${uboot}; then " \
	99	"if itest ${filesize} > 0; then " \
	100	"mmc dev ${mmcdev}; mmc rescan; " \
e7203d77 MN	101	"setexpr blkc ${filesize} + 0x1ff; " \
e7203d77 MN	102	"setexpr blkc ${blkc} / 0x200; " \
cb07d74e MN	103	"if itest ${blkc} <= ${uboot_size}; then " \
	104	"mmc write ${loadaddr} ${uboot_start} " \
	105	"${blkc}; " \
	106	"fi; " \
	107	"fi; fi; " \
	108	"setenv filesize; setenv blkc \0" \
	109	"update_kernel=run kernel_name; " \
	110	"if tftp ${kernel}; then " \
	111	"if itest ${filesize} > 0; then " \
	112	"mmc dev ${mmcdev}; mmc rescan; " \
e7203d77 MN	113	"setexpr blkc ${filesize} + 0x1ff; " \
e7203d77 MN	114	"setexpr blkc ${blkc} / 0x200; " \
cb07d74e MN	115	"if itest ${blkc} <= ${kernel_size}; then " \
	116	"mmc write ${loadaddr} " \
	117	"${kernel_start} ${blkc}; " \
	118	"fi; " \
	119	"fi; " \
	120	"fi; " \
	121	"setenv filesize; setenv blkc \0" \
	122	"update_fdt=if tftp ${fdt_file}; then " \
	123	"if itest ${filesize} > 0; then " \
	124	"mmc dev ${mmcdev}; mmc rescan; " \
e7203d77 MN	125	"setexpr blkc ${filesize} + 0x1ff; " \
e7203d77 MN	126	"setexpr blkc ${blkc} / 0x200; " \
cb07d74e MN	127	"if itest ${blkc} <= ${fdt_size}; then " \
	128	"mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
	129	"fi; " \
	130	"fi; fi; " \
	131	"setenv filesize; setenv blkc \0" \
	132
	133	#define CONFIG_BOOTCOMMAND \
	134	"run mmcboot; run netboot; run panicboot"
	135
	136	#elif defined(CONFIG_TQMA6X_SPI_BOOT)
	137
cb07d74e MN	138	#define TQMA6_UBOOT_OFFSET 0x400
	139	#define TQMA6_UBOOT_SECTOR_START 0x0
	140	/* max u-boot size: 512k */
52835468	141	#define TQMA6_UBOOT_SECTOR_SIZE TQMA6_SPI_FLASH_SECTOR_SIZE
cb07d74e MN	142	#define TQMA6_UBOOT_SECTOR_COUNT 0x8
	143	#define TQMA6_UBOOT_SIZE (TQMA6_UBOOT_SECTOR_SIZE * \
	144	TQMA6_UBOOT_SECTOR_COUNT)
	145
cb07d74e MN	146	#define TQMA6_FDT_OFFSET (CONFIG_ENV_OFFSET_REDUND + \
cb07d74e MN	147	CONFIG_ENV_SECT_SIZE)
52835468	148	#define TQMA6_FDT_SECT_SIZE (TQMA6_SPI_FLASH_SECTOR_SIZE)
cb07d74e MN	149
	150	#define TQMA6_FDT_SECTOR_START 0x0a /* 8 Sector u-boot, 2 Sector env */
	151	#define TQMA6_FDT_SECTOR_COUNT 0x01
	152
	153	#define TQMA6_KERNEL_SECTOR_START 0x10
	154	#define TQMA6_KERNEL_SECTOR_COUNT 0x60
	155
	156	#define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
	157	"mmcblkdev=0\0" \
	158	"uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0" \
	159	"uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0" \
	160	"fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0" \
	161	"fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0" \
	162	"kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0" \
	163	"kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0" \
	164	"update_uboot=if tftp ${uboot}; then " \
	165	"if itest ${filesize} > 0; then " \
	166	"setexpr blkc ${filesize} + " \
	167	__stringify(TQMA6_UBOOT_OFFSET) "; " \
	168	"setexpr size ${uboot_sectors} * " \
52835468	169	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e MN	170	"if itest ${blkc} <= ${size}; then " \
	171	"sf probe; " \
	172	"sf erase 0 ${size}; " \
	173	"sf write ${loadaddr} ${uboot_offset} " \
	174	"${filesize}; " \
	175	"fi; " \
	176	"fi; fi; " \
	177	"setenv filesize 0; setenv blkc; setenv size \0" \
	178	"update_kernel=run kernel_name; if tftp ${kernel}; then " \
	179	"if itest ${filesize} > 0; then " \
	180	"setexpr size ${kernel_sectors} * " \
52835468	181	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e	182	"setexpr offset ${kernel_start} * " \
52835468	183	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e MN	184	"if itest ${filesize} <= ${size}; then " \
	185	"sf probe; " \
	186	"sf erase ${offset} ${size}; " \
	187	"sf write ${loadaddr} ${offset} " \
	188	"${filesize}; " \
	189	"fi; " \
	190	"fi; fi; " \
	191	"setenv filesize 0; setenv size ; setenv offset\0" \
	192	"update_fdt=if tftp ${fdt_file}; then " \
	193	"if itest ${filesize} > 0; then " \
	194	"setexpr size ${fdt_sectors} * " \
52835468	195	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e	196	"setexpr offset ${fdt_start} * " \
52835468	197	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e MN	198	"if itest ${filesize} <= ${size}; then " \
	199	"sf probe; " \
	200	"sf erase ${offset} ${size}; " \
	201	"sf write ${loadaddr} ${offset} " \
	202	"${filesize}; " \
	203	"fi; " \
	204	"fi; fi; " \
	205	"setenv filesize 0; setenv size ; setenv offset\0" \
	206	"loadimage=sf probe; " \
	207	"setexpr size ${kernel_sectors} * " \
52835468	208	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e	209	"setexpr offset ${kernel_start} * " \
52835468	210	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e MN	211	"sf read ${loadaddr} ${offset} ${size}; " \
	212	"setenv size ; setenv offset\0" \
	213	"loadfdt=sf probe; " \
	214	"setexpr size ${fdt_sectors} * " \
52835468	215	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e	216	"setexpr offset ${fdt_start} * " \
52835468	217	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
0b14f1a6	218	"sf read ${fdt_addr} ${offset} ${size}; " \
cb07d74e MN	219	"setenv size ; setenv offset\0" \
cb07d74e MN	220
cb07d74e MN	221	#define CONFIG_BOOTCOMMAND \
	222	"sf probe; run mmcboot; run netboot; run panicboot" \
	223
	224	#else
	225
	226	#error "need to define boot source"
	227
	228	#endif
	229
	230	/* 128 MiB offset as in ARM related docu for linux suggested */
	231	#define TQMA6_FDT_ADDRESS 0x18000000
	232
9e9846a4 MN	233	/* set to a resonable value, changeable by user */
	234	#define TQMA6_CMA_SIZE 160M
	235
cb07d74e MN	236	#define CONFIG_EXTRA_ENV_SETTINGS \
	237	"board=tqma6\0" \
	238	"uimage=uImage\0" \
	239	"zimage=zImage\0" \
	240	"boot_type=bootz\0" \
	241	"kernel_name=if test \"${boot_type}\" != bootz; then " \
	242	"setenv kernel ${uimage}; " \
	243	"else setenv kernel ${zimage}; fi\0" \
	244	"uboot=u-boot.imx\0" \
	245	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
	246	"fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0" \
dc05e47a	247	"console=" CONSOLE_DEV "\0" \
9e9846a4	248	"cma_size="__stringify(TQMA6_CMA_SIZE)"\0" \
cb07d74e MN	249	"fdt_high=0xffffffff\0" \
cb07d74e MN	250	"initrd_high=0xffffffff\0" \
34713901	251	"rootfsmode=ro\0" \
9e9846a4	252	"addcma=setenv bootargs ${bootargs} cma=${cma_size}\0" \
cb07d74e MN	253	"addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \
	254	"addfb=setenv bootargs ${bootargs} " \
	255	"imx-fbdev.legacyfb_depth=32 consoleblank=0\0" \
	256	"mmcpart=2\0" \
	257	"mmcblkdev=0\0" \
9e9846a4	258	"mmcargs=run addmmc addtty addfb addcma\0" \
cb07d74e	259	"addmmc=setenv bootargs ${bootargs} " \
34713901 MN	260	"root=/dev/mmcblk${mmcblkdev}p${mmcpart} ${rootfsmode} " \
34713901 MN	261	"rootwait\0" \
cb07d74e MN	262	"mmcboot=echo Booting from mmc ...; " \
	263	"setenv bootargs; " \
	264	"run mmcargs; " \
	265	"run loadimage; " \
	266	"if run loadfdt; then " \
	267	"echo boot device tree kernel ...; " \
	268	"${boot_type} ${loadaddr} - ${fdt_addr}; " \
	269	"else " \
	270	"${boot_type}; " \
	271	"fi;\0" \
	272	"setenv bootargs \0" \
	273	"netdev=eth0\0" \
	274	"rootpath=/srv/nfs/tqma6\0" \
	275	"ipmode=static\0" \
9e9846a4	276	"netargs=run addnfs addip addtty addfb addcma\0" \
cb07d74e MN	277	"addnfs=setenv bootargs ${bootargs} " \
	278	"root=/dev/nfs rw " \
	279	"nfsroot=${serverip}:${rootpath},v3,tcp;\0" \
	280	"addip_static=setenv bootargs ${bootargs} " \
	281	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:" \
	282	"${hostname}:${netdev}:off\0" \
	283	"addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0" \
	284	"addip=if test \"${ipmode}\" != static; then " \
	285	"run addip_dynamic; else run addip_static; fi\0" \
	286	"set_getcmd=if test \"${ipmode}\" != static; then " \
	287	"setenv getcmd dhcp; setenv autoload yes; " \
	288	"else setenv getcmd tftp; setenv autoload no; fi\0" \
	289	"netboot=echo Booting from net ...; " \
	290	"run kernel_name; " \
	291	"run set_getcmd; " \
	292	"setenv bootargs; " \
	293	"run netargs; " \
	294	"if ${getcmd} ${kernel}; then " \
	295	"if ${getcmd} ${fdt_addr} ${fdt_file}; then " \
	296	"${boot_type} ${loadaddr} - ${fdt_addr}; " \
	297	"fi; " \
	298	"fi; " \
	299	"echo ... failed\0" \
	300	"panicboot=echo No boot device !!! reset\0" \
	301	TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
	302
cb07d74e	303	/* Physical Memory Map */
cb07d74e MN	304	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
	305
	306	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
	307	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	308	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
	309
	310	#define CONFIG_SYS_INIT_SP_OFFSET \
	311	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	312	#define CONFIG_SYS_INIT_SP_ADDR \
	313	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
	314
6b396b31 SR	315	/*
	316	* All the defines above are for the TQMa6 SoM
	317	*
	318	* Now include the baseboard specific configuration
	319	*/
	320	#ifdef CONFIG_MBA6
	321	#include "tqma6_mba6.h"
452308c0 SR	322	#elif CONFIG_WRU4
452308c0 SR	323	#include "tqma6_wru4.h"
6b396b31 SR	324	#else
	325	#error "No baseboard for the TQMa6 defined!"
	326	#endif
	327
	328	/* Support at least the sensor on TQMa6 SOM */
6b396b31	329
cb07d74e	330	#endif /* __CONFIG_H */