[J-u-boot.git] / include / configs / apalis-tk1.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright (c) 2017 Toradex, Inc.
 *
 * Configuration settings for the Toradex Apalis TK1 modules.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include <linux/sizes.h>

#include "tegra124-common.h"

#define CONFIG_ARCH_MISC_INIT

/* Board-specific serial config */
#define CONFIG_TEGRA_ENABLE_UARTA
#define CONFIG_SYS_NS16550_COM1		NV_PA_APB_UARTA_BASE

/* Environment in eMMC, before config block at the end of 1st "boot sector" */
#define CONFIG_ENV_OFFSET		(-CONFIG_ENV_SIZE + \
					 CONFIG_TDX_CFG_BLOCK_OFFSET)
#define CONFIG_SYS_MMC_ENV_DEV		0
#define CONFIG_SYS_MMC_ENV_PART		1

/* PCI host support */
#undef CONFIG_PCI_SCAN_SHOW

/* PCI networking support */
#define CONFIG_E1000_NO_NVM

/* General networking support */
#define CONFIG_IP_DEFRAG
#define CONFIG_TFTP_BLOCKSIZE		16352
#define CONFIG_TFTP_TSIZE

#undef CONFIG_IPADDR
#define CONFIG_IPADDR		192.168.10.2
#define CONFIG_NETMASK		255.255.255.0
#undef CONFIG_SERVERIP
#define CONFIG_SERVERIP		192.168.10.1

#define DFU_ALT_EMMC_INFO	"apalis-tk1.img raw 0x0 0x500 mmcpart 1; " \
				"boot part 0 1 mmcpart 0; " \
				"rootfs part 0 2 mmcpart 0; " \
				"uImage fat 0 1 mmcpart 0; " \
				"tegra124-apalis-eval.dtb fat 0 1 mmcpart 0"

#define EMMC_BOOTCMD \
	"emmcargs=ip=off root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait\0" \
	"emmcboot=run setup; setenv bootargs ${defargs} ${emmcargs} " \
		"${setupargs} ${vidargs}; echo Booting from internal eMMC " \
		"chip...; run emmcdtbload; load mmc 0:1 ${kernel_addr_r} " \
		"${boot_file} && run fdt_fixup && " \
		"bootm ${kernel_addr_r} - ${dtbparam}\0" \
	"emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} " \
		"${soc}-apalis-${fdt_board}.dtb && " \
		"setenv dtbparam ${fdt_addr_r}\0"

#define NFS_BOOTCMD \
	"nfsargs=ip=:::::eth0:on root=/dev/nfs rw\0" \
	"nfsboot=pci enum; run setup; setenv bootargs ${defargs} ${nfsargs} " \
		"${setupargs} ${vidargs}; echo Booting via DHCP/TFTP/NFS...; " \
		"run nfsdtbload; dhcp ${kernel_addr_r} " \
		"&& run fdt_fixup && bootm ${kernel_addr_r} - ${dtbparam}\0" \
	"nfsdtbload=setenv dtbparam; tftp ${fdt_addr_r} " \
		"${soc}-apalis-${fdt_board}.dtb " \
		"&& setenv dtbparam ${fdt_addr_r}\0"

#define SD_BOOTCMD \
	"sdargs=ip=off root=/dev/mmcblk1p2 rw rootfstype=ext4 rootwait\0" \
	"sdboot=run setup; setenv bootargs ${defargs} ${sdargs} ${setupargs} " \
		"${vidargs}; echo Booting from SD card in 8bit slot...; " \
		"run sddtbload; load mmc 1:1 ${kernel_addr_r} " \
		"${boot_file} && run fdt_fixup && " \
		"bootm ${kernel_addr_r} - ${dtbparam}\0" \
	"sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} " \
		"${soc}-apalis-${fdt_board}.dtb " \
		"&& setenv dtbparam ${fdt_addr_r}\0"

#define USB_BOOTCMD \
	"usbargs=ip=off root=/dev/sda2 rw rootfstype=ext4 rootwait\0" \
	"usbboot=run setup; setenv bootargs ${defargs} ${setupargs} " \
		"${usbargs} ${vidargs}; echo Booting from USB stick...; " \
		"usb start && run usbdtbload; load usb 0:1 ${kernel_addr_r} " \
		"${boot_file} && run fdt_fixup && " \
		"bootm ${kernel_addr_r} - ${dtbparam}\0" \
	"usbdtbload=setenv dtbparam; load usb 0:1 ${fdt_addr_r} " \
		"${soc}-apalis-${fdt_board}.dtb " \
		"&& setenv dtbparam ${fdt_addr_r}\0"

#define BOARD_EXTRA_ENV_SETTINGS \
	"boot_file=uImage\0" \
	"console=ttyS0\0" \
	"defargs=lp0_vec=2064@0xf46ff000 core_edp_mv=1150 core_edp_ma=4000 " \
		"usb_port_owner_info=2 lane_owner_info=6 emc_max_dvfs=0\0" \
	"dfu_alt_info=" DFU_ALT_EMMC_INFO "\0" \
	EMMC_BOOTCMD \
	"fdt_board=eval\0" \
	"fdt_fixup=;\0" \
	NFS_BOOTCMD \
	SD_BOOTCMD \
	"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
		"00:14:2d:00:00:00; fi; pci enum && tftpboot ${loadaddr} " \
		"flash_eth.img && source ${loadaddr}\0" \
	"setsdupdate=setenv interface mmc; setenv drive 1; mmc rescan; " \
		"load ${interface} ${drive}:1 ${loadaddr} flash_blk.img " \
		"|| setenv drive 2; mmc rescan; load ${interface} ${drive}:1 " \
		"${loadaddr} flash_blk.img && " \
		"source ${loadaddr}\0" \
	"setup=setenv setupargs igb_mac=${ethaddr} " \
		"consoleblank=0 no_console_suspend=1 console=tty1 " \
		"console=${console},${baudrate}n8 debug_uartport=lsport,0 " \
		"${memargs}\0" \
	"setupdate=run setsdupdate || run setusbupdate || run setethupdate\0" \
	"setusbupdate=usb start && setenv interface usb; setenv drive 0; " \
		"load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
		"source ${loadaddr}\0" \
	USB_BOOTCMD \
	"vidargs=video=tegrafb0:640x480-16@60 fbcon=map:1\0"

/* Increase console I/O buffer size */
#undef CONFIG_SYS_CBSIZE
#define CONFIG_SYS_CBSIZE		1024

/* Increase arguments buffer size */
#undef CONFIG_SYS_BARGSIZE
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

/* Increase maximum number of arguments */
#undef CONFIG_SYS_MAXARGS
#define CONFIG_SYS_MAXARGS		32

#define CONFIG_CMD_TIME

#define CONFIG_SYS_BOOT_RAMDISK_HIGH

#include "tegra-common-usb-gadget.h"
#include "tegra-common-post.h"

/* Reserve top 1M for secure RAM */
#define CONFIG_ARMV7_SECURE_BASE		0xfff00000
#define CONFIG_ARMV7_SECURE_RESERVE_SIZE	0x00100000

#endif /* __CONFIG_H */
Commit	Line	Data
83d290c5	1	/* SPDX-License-Identifier: GPL-2.0+ */
f38f5f4b MZ	2	/*
	3	* Copyright (c) 2017 Toradex, Inc.
	4	*
	5	* Configuration settings for the Toradex Apalis TK1 modules.
f38f5f4b MZ	6	*/
	7
	8	#ifndef __CONFIG_H
	9	#define __CONFIG_H
	10
	11	#include <linux/sizes.h>
	12
f38f5f4b MZ	13	#include "tegra124-common.h"
	14
	15	#define CONFIG_ARCH_MISC_INIT
	16
f38f5f4b MZ	17	/* Board-specific serial config */
	18	#define CONFIG_TEGRA_ENABLE_UARTA
	19	#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE
	20
f38f5f4b	21	/* Environment in eMMC, before config block at the end of 1st "boot sector" */
f38f5f4b MZ	22	#define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE + \
	23	CONFIG_TDX_CFG_BLOCK_OFFSET)
	24	#define CONFIG_SYS_MMC_ENV_DEV 0
	25	#define CONFIG_SYS_MMC_ENV_PART 1
	26
f38f5f4b MZ	27	/* PCI host support */
f38f5f4b MZ	28	#undef CONFIG_PCI_SCAN_SHOW
f38f5f4b MZ	29
	30	/* PCI networking support */
	31	#define CONFIG_E1000_NO_NVM
	32
	33	/* General networking support */
	34	#define CONFIG_IP_DEFRAG
	35	#define CONFIG_TFTP_BLOCKSIZE 16352
	36	#define CONFIG_TFTP_TSIZE
	37
f38f5f4b MZ	38	#undef CONFIG_IPADDR
	39	#define CONFIG_IPADDR 192.168.10.2
	40	#define CONFIG_NETMASK 255.255.255.0
	41	#undef CONFIG_SERVERIP
	42	#define CONFIG_SERVERIP 192.168.10.1
	43
f38f5f4b MZ	44	#define DFU_ALT_EMMC_INFO "apalis-tk1.img raw 0x0 0x500 mmcpart 1; " \
	45	"boot part 0 1 mmcpart 0; " \
	46	"rootfs part 0 2 mmcpart 0; " \
	47	"uImage fat 0 1 mmcpart 0; " \
	48	"tegra124-apalis-eval.dtb fat 0 1 mmcpart 0"
	49
	50	#define EMMC_BOOTCMD \
	51	"emmcargs=ip=off root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait\0" \
	52	"emmcboot=run setup; setenv bootargs ${defargs} ${emmcargs} " \
	53	"${setupargs} ${vidargs}; echo Booting from internal eMMC " \
	54	"chip...; run emmcdtbload; load mmc 0:1 ${kernel_addr_r} " \
	55	"${boot_file} && run fdt_fixup && " \
	56	"bootm ${kernel_addr_r} - ${dtbparam}\0" \
	57	"emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} " \
	58	"${soc}-apalis-${fdt_board}.dtb && " \
	59	"setenv dtbparam ${fdt_addr_r}\0"
	60
	61	#define NFS_BOOTCMD \
	62	"nfsargs=ip=:::::eth0:on root=/dev/nfs rw\0" \
	63	"nfsboot=pci enum; run setup; setenv bootargs ${defargs} ${nfsargs} " \
	64	"${setupargs} ${vidargs}; echo Booting via DHCP/TFTP/NFS...; " \
	65	"run nfsdtbload; dhcp ${kernel_addr_r} " \
	66	"&& run fdt_fixup && bootm ${kernel_addr_r} - ${dtbparam}\0" \
	67	"nfsdtbload=setenv dtbparam; tftp ${fdt_addr_r} " \
	68	"${soc}-apalis-${fdt_board}.dtb " \
	69	"&& setenv dtbparam ${fdt_addr_r}\0"
	70
	71	#define SD_BOOTCMD \
1c1238f1	72	"sdargs=ip=off root=/dev/mmcblk1p2 rw rootfstype=ext4 rootwait\0" \
f38f5f4b MZ	73	"sdboot=run setup; setenv bootargs ${defargs} ${sdargs} ${setupargs} " \
	74	"${vidargs}; echo Booting from SD card in 8bit slot...; " \
	75	"run sddtbload; load mmc 1:1 ${kernel_addr_r} " \
	76	"${boot_file} && run fdt_fixup && " \
	77	"bootm ${kernel_addr_r} - ${dtbparam}\0" \
	78	"sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} " \
	79	"${soc}-apalis-${fdt_board}.dtb " \
	80	"&& setenv dtbparam ${fdt_addr_r}\0"
	81
	82	#define USB_BOOTCMD \
1c1238f1	83	"usbargs=ip=off root=/dev/sda2 rw rootfstype=ext4 rootwait\0" \
f38f5f4b MZ	84	"usbboot=run setup; setenv bootargs ${defargs} ${setupargs} " \
	85	"${usbargs} ${vidargs}; echo Booting from USB stick...; " \
	86	"usb start && run usbdtbload; load usb 0:1 ${kernel_addr_r} " \
	87	"${boot_file} && run fdt_fixup && " \
	88	"bootm ${kernel_addr_r} - ${dtbparam}\0" \
	89	"usbdtbload=setenv dtbparam; load usb 0:1 ${fdt_addr_r} " \
	90	"${soc}-apalis-${fdt_board}.dtb " \
	91	"&& setenv dtbparam ${fdt_addr_r}\0"
	92
	93	#define BOARD_EXTRA_ENV_SETTINGS \
	94	"boot_file=uImage\0" \
	95	"console=ttyS0\0" \
	96	"defargs=lp0_vec=2064@0xf46ff000 core_edp_mv=1150 core_edp_ma=4000 " \
	97	"usb_port_owner_info=2 lane_owner_info=6 emc_max_dvfs=0\0" \
	98	"dfu_alt_info=" DFU_ALT_EMMC_INFO "\0" \
	99	EMMC_BOOTCMD \
	100	"fdt_board=eval\0" \
	101	"fdt_fixup=;\0" \
	102	NFS_BOOTCMD \
	103	SD_BOOTCMD \
	104	"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
	105	"00:14:2d:00:00:00; fi; pci enum && tftpboot ${loadaddr} " \
	106	"flash_eth.img && source ${loadaddr}\0" \
	107	"setsdupdate=setenv interface mmc; setenv drive 1; mmc rescan; " \
	108	"load ${interface} ${drive}:1 ${loadaddr} flash_blk.img " \
	109	"\|\| setenv drive 2; mmc rescan; load ${interface} ${drive}:1 " \
	110	"${loadaddr} flash_blk.img && " \
	111	"source ${loadaddr}\0" \
	112	"setup=setenv setupargs igb_mac=${ethaddr} " \
	113	"consoleblank=0 no_console_suspend=1 console=tty1 " \
	114	"console=${console},${baudrate}n8 debug_uartport=lsport,0 " \
	115	"${memargs}\0" \
	116	"setupdate=run setsdupdate \|\| run setusbupdate \|\| run setethupdate\0" \
	117	"setusbupdate=usb start && setenv interface usb; setenv drive 0; " \
	118	"load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
	119	"source ${loadaddr}\0" \
	120	USB_BOOTCMD \
	121	"vidargs=video=tegrafb0:640x480-16@60 fbcon=map:1\0"
	122
	123	/* Increase console I/O buffer size */
	124	#undef CONFIG_SYS_CBSIZE
	125	#define CONFIG_SYS_CBSIZE 1024
	126
	127	/* Increase arguments buffer size */
	128	#undef CONFIG_SYS_BARGSIZE
	129	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
	130
f38f5f4b MZ	131	/* Increase maximum number of arguments */
	132	#undef CONFIG_SYS_MAXARGS
	133	#define CONFIG_SYS_MAXARGS 32
	134
	135	#define CONFIG_CMD_TIME
	136
f38f5f4b MZ	137	#define CONFIG_SYS_BOOT_RAMDISK_HIGH
	138
	139	#include "tegra-common-usb-gadget.h"
	140	#include "tegra-common-post.h"
	141
	142	/* Reserve top 1M for secure RAM */
	143	#define CONFIG_ARMV7_SECURE_BASE 0xfff00000
	144	#define CONFIG_ARMV7_SECURE_RESERVE_SIZE 0x00100000
	145
	146	#endif /* __CONFIG_H */