[J-u-boot.git] / include / configs / MPC8641HPCN.h

/*
 * Copyright 2006 Freescale Semiconductor.
 *
 * Srikanth Srinivasan ([email protected])
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * MPC8641HPCN board configuration file
 *
 * Make sure you change the MAC address and other network params first,
 * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/* High Level Configuration Options */
#define CONFIG_MPC86xx		1	/* MPC86xx */
#define CONFIG_MPC8641		1	/* MPC8641 specific */
#define CONFIG_MPC8641HPCN	1	/* MPC8641HPCN board specific */
#define CONFIG_NUM_CPUS         2       /* Number of CPUs in the system */
#define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
#undef DEBUG

#ifdef RUN_DIAG
#define CFG_DIAG_ADDR        0xff800000
#endif

#define CFG_RESET_ADDRESS    0xfff00100

#undef CONFIG_PCI

#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE

#undef CONFIG_DDR_DLL			/* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
#define CONFIG_DDR_ECC			/* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE		0xDeadBeef

#define CONFIG_ALTIVEC          1

/*
 * L2CR setup -- make sure this is right for your board!
 */
#define CFG_L2
#define L2_INIT		0
#define L2_ENABLE	(L2CR_L2E)

#ifndef CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
#endif

#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */

#undef	CFG_DRAM_TEST			/* memory test, takes time */
#define CFG_MEMTEST_START	0x00200000	/* memtest region */
#define CFG_MEMTEST_END		0x00400000


/*
 * Base addresses -- Note these are effective addresses where the
 * actual resources get mapped (not physical addresses)
 */
#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
#define CFG_CCSRBAR		0xf8000000	/* relocated CCSRBAR */
#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */


/*
 * DDR Setup
 */
#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE

#define MPC86xx_DDR_SDRAM_CLK_CNTL

#if defined(CONFIG_SPD_EEPROM)
    /*
     * Determine DDR configuration from I2C interface.
     */
    #define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */

#else
    /*
     * Manually set up DDR parameters
     */

/* DDR I */
#if 1
    #define CFG_SDRAM_SIZE	256		/* DDR is 256MB */

    #define CFG_DDR_CS0_BNDS	0x0000000F
    #define CFG_DDR_CS0_CONFIG	0x80010102      /* Enable, no interleaving */
    #define CFG_DDR_EXT_REFRESH 0x00000000
    #define CFG_DDR_TIMING_0    0x00260802
    #define CFG_DDR_TIMING_1	0x39357322
    #define CFG_DDR_TIMING_2	0x14904cc8
    #define CFG_DDR_MODE_1	0x00480432
    #define CFG_DDR_MODE_2	0x00000000
    #define CFG_DDR_INTERVAL	0x06090100
    #define CFG_DDR_DATA_INIT   0xdeadbeef
    #define CFG_DDR_CLK_CTRL    0x03800000
    #define CFG_DDR_OCD_CTRL    0x00000000
    #define CFG_DDR_OCD_STATUS  0x00000000
    #define CFG_DDR_CONTROL	0xe3008000	/* Type = DDR2 */
    #define CFG_DDR_CONTROL2	0x04400000

    //Not used in fixed_sdram function

    #define CFG_DDR_MODE	0x00000022
    #define CFG_DDR_CS1_BNDS	0x00000000
    #define CFG_DDR_CS2_BNDS	0x00000FFF  //Not done
    #define CFG_DDR_CS3_BNDS	0x00000FFF  //Not done
    #define CFG_DDR_CS4_BNDS	0x00000FFF  //Not done
    #define CFG_DDR_CS5_BNDS	0x00000FFF  //Not done
#endif
#endif


/*
 * In MPC8641HPCN, we allocate 16MB flash spaces at fe000000 and ff000000
 * We only have an 8MB flash. In effect, the addresses from fe000000 to fe7fffff
 * map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff.
 * However, when u-boot comes up, the flash_init needs hard start addresses
 * to build its info table. For user convenience, we have the flash addresses
 * as fe800000 and ff800000. That way, when we do flash operations, u-boot
 * knows where the flash is and the user can download u-boot code from promjet to
 * fef00000 <- more intuitive than fe700000. Note that, on switching the boot
 * location, fef00000 becomes fff00000.
 */
#define CFG_FLASH_BASE          0xfe800000     /* start of FLASH 32M */
#define CFG_FLASH_BASE2		0xff800000

#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}

#define CFG_BR0_PRELIM		0xff001001	/* port size 16bit */
#define CFG_OR0_PRELIM		0xff006ff7	/* 16MB Boot Flash area*/

#define CFG_BR1_PRELIM		0xfe001001	/* port size 16bit */
#define CFG_OR1_PRELIM		0xff006ff7	/* 16MB Alternate Boot Flash area*/

#define CFG_BR2_PRELIM		0xf8201001	/* port size 16bit */
#define CFG_OR2_PRELIM		0xfff06ff7	/* 1MB Compact Flash area*/

#define CFG_BR3_PRELIM		0xf8100801	/* port size 8bit */
#define CFG_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/


#define PIXIS_BASE	0xf8100000      /* PIXIS registers */
#define PIXIS_ID		0x0	/* Board ID at offset 0 */
#define PIXIS_VER		0x1	/* Board version at offset 1 */
#define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
#define PIXIS_RST		0x4	/* PIXIS Reset Control register */
#define PIXIS_AUX		0x6	/* PIXIS Auxiliary register; Scratch register */
#define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
#define PIXIS_VCTL		0x10	/* VELA Control Register */
#define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
#define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
#define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
#define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
#define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
#define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
#define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */

#define CFG_MAX_FLASH_BANKS	2		/* number of banks */
#define CFG_MAX_FLASH_SECT	128		/* sectors per device */

#undef	CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */

#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO

#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
#undef  CFG_RAMBOOT
#endif

#if !defined(CFG_RAMBOOT)
#define CONFIG_SPD_EEPROM        	/* Use SPD EEPROM for DDR setup*/
#endif

#undef CONFIG_CLOCKS_IN_MHZ

#define CONFIG_L1_INIT_RAM
#undef CFG_INIT_RAM_LOCK
#ifndef CFG_INIT_RAM_LOCK
#define CFG_INIT_RAM_ADDR	0x0fd00000	/* Initial RAM address */
#else
#define CFG_INIT_RAM_ADDR	0xf8400000	/* Initial RAM address */
#endif
#define CFG_INIT_RAM_END    	0x4000	    	/* End of used area in RAM */

#define CFG_GBL_DATA_SIZE  	128		/* num bytes initial data */
#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET

#define CFG_MONITOR_LEN	    	(256 * 1024)    /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN	    	(128 * 1024)    /* Reserved for malloc */

/* Serial Port */
#define CONFIG_CONS_INDEX     1
#undef	CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE    1
#define CFG_NS16550_CLK		get_bus_freq(0)

#define CFG_BAUDRATE_TABLE  \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

#define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
#define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)

/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef  CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif

/*
 * Pass open firmware flat tree to kernel
 */
#define CONFIG_OF_FLAT_TREE	1
#define CONFIG_OF_BOARD_SETUP	1

/* maximum size of the flat tree (8K) */
#define OF_FLAT_TREE_MAX_SIZE	8192

#define OF_CPU		"PowerPC,8641@0"
#define OF_SOC		"soc8641@f8000000"
#define OF_TBCLK	(bd->bi_busfreq / 8)
#define OF_STDOUT_PATH	"/soc8641@f8000000/serial@4500"

#define CFG_64BIT_VSPRINTF	1
#define CFG_64BIT_STRTOUL	1

/* I2C */
#define  CONFIG_HARD_I2C		/* I2C with hardware support*/
#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
#define CFG_I2C_SLAVE		0x7F
#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */

/* RapidIO MMU */
#define CFG_RIO_MEM_BASE	0xc0000000	/* base address */
#define CFG_RIO_MEM_PHYS	CFG_RIO_MEM_BASE
#define CFG_RIO_MEM_SIZE	0x20000000	/* 128M */

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CFG_PCI1_MEM_BASE	0x80000000
#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
#define CFG_PCI1_IO_BASE	0xe2000000
#define CFG_PCI1_IO_PHYS	CFG_PCI1_IO_BASE
#define CFG_PCI1_IO_SIZE	0x1000000	/* 16M */

/* For RTL8139 */
#define _IO_BASE                0x00000000

#define CFG_PCI2_MEM_BASE	0xa0000000
#define CFG_PCI2_MEM_PHYS	CFG_PCI2_MEM_BASE
#define CFG_PCI2_MEM_SIZE	0x10000000	/* 256M */
#define CFG_PCI2_IO_BASE	0xe3000000
#define CFG_PCI2_IO_PHYS	CFG_PCI2_IO_BASE
#define CFG_PCI2_IO_SIZE	0x1000000	/* 16M */


#if defined(CONFIG_PCI)

#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */

#undef CFG_SCSI_SCAN_BUS_REVERSE

#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */

#define CONFIG_RTL8139

#undef CONFIG_EEPRO100
#undef CONFIG_TULIP

#if !defined(CONFIG_PCI_PNP)
    #define PCI_ENET0_IOADDR	0xe0000000
    #define PCI_ENET0_MEMADDR	0xe0000000
    #define PCI_IDSEL_NUMBER	0x0c 	/* slot0->3(IDSEL)=12->15 */
#endif

#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */

#endif	/* CONFIG_PCI */


#if defined(CONFIG_TSEC_ENET)

#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 	1
#endif

#define CONFIG_MII		1	/* MII PHY management */

#define CONFIG_MPC86XX_TSEC1    1
#define CONFIG_MPC86XX_TSEC1_NAME       "eTSEC1"
#define CONFIG_MPC86XX_TSEC2    1
#define CONFIG_MPC86XX_TSEC2_NAME       "eTSEC2"
#define CONFIG_MPC86XX_TSEC3    1
#define CONFIG_MPC86XX_TSEC3_NAME       "eTSEC3"
#define CONFIG_MPC86XX_TSEC4    1
#define CONFIG_MPC86XX_TSEC4_NAME       "eTSEC4"

#define TSEC1_PHY_ADDR		0
#define TSEC2_PHY_ADDR		1
#define TSEC3_PHY_ADDR		2
#define TSEC4_PHY_ADDR		3
#define TSEC1_PHYIDX		0
#define TSEC2_PHYIDX		0
#define TSEC3_PHYIDX		0
#define TSEC4_PHYIDX		0

#define CONFIG_ETHPRIME		"eTSEC1"

#endif	/* CONFIG_TSEC_ENET */


/* BAT0         2G     Cacheable, non-guarded
 * 0x0000_0000  2G     DDR
 */
#define CFG_DBAT0L      ( BATL_PP_RW | BATL_CACHEINHIBIT \
			| BATL_GUARDEDSTORAGE | BATL_MEMCOHERENCE )
#define CFG_DBAT0U      ( BATU_BL_512M | BATU_VS | BATU_VP )
#define CFG_IBAT0L      ( BATL_PP_RW | BATL_CACHEINHIBIT | BATL_MEMCOHERENCE)
#define CFG_IBAT0U      CFG_DBAT0U

/* BAT1         1G     Cache-inhibited, guarded
 * 0x8000_0000  512M   PCI-Express 1 Memory
 * 0xa000_0000  512M   PCI-Express 2 Memory
 ** SS - Changed it for operating from 0xd0000000
 */
#define CFG_DBAT1L      ( CFG_PCI1_MEM_BASE | BATL_PP_RW \
			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT1U      (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_IBAT1L      (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT1U      CFG_DBAT1U

/* BAT2         512M   Cache-inhibited, guarded
 * 0xc000_0000  512M   RapidIO Memory
 */
#define CFG_DBAT2L      (CFG_RIO_MEM_BASE | BATL_PP_RW \
			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT2U      (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
#define CFG_IBAT2L      (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT2U      CFG_DBAT2U

/* BAT3         4M     Cache-inhibited, guarded
 * 0xf800_0000  4M     CCSR
 */
#define CFG_DBAT3L      ( CFG_CCSRBAR | BATL_PP_RW \
			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT3U      (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
#define CFG_IBAT3L      (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT3U      CFG_DBAT3U

/* BAT4         32M    Cache-inhibited, guarded
 * 0xe200_0000  16M    PCI-Express 1 I/O
 * 0xe300_0000  16M    PCI-Express 2 I/0
 ** SS - Note that this is at 0xe0000000
 */
#define CFG_DBAT4L      ( CFG_PCI1_IO_BASE | BATL_PP_RW \
			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT4U      (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
#define CFG_IBAT4L      (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT4U      CFG_DBAT4U

/* BAT5         128K   Cacheable, non-guarded
 * 0xe401_0000  128K   Init RAM for stack in the CPU DCache (no backing memory)
 */
#define CFG_DBAT5L      (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CFG_DBAT5U      (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
#define CFG_IBAT5L      CFG_DBAT5L
#define CFG_IBAT5U      CFG_DBAT5U

/* BAT6         32M    Cache-inhibited, guarded
 * 0xfe00_0000  32M    FLASH
 */
#define CFG_DBAT6L      ( CFG_FLASH_BASE | BATL_PP_RW \
			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT6U      (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
#define CFG_IBAT6L      (CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CFG_IBAT6U      CFG_DBAT6U

#define CFG_DBAT7L 0x00000000
#define CFG_DBAT7U 0x00000000
#define CFG_IBAT7L 0x00000000
#define CFG_IBAT7U 0x00000000


/*
 * Environment
 */
#ifndef CFG_RAMBOOT
    #define CFG_ENV_IS_IN_FLASH	1
    #define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
    #define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
    #define CFG_ENV_SIZE		0x2000
#else
    #define CFG_NO_FLASH		1	/* Flash is not usable now */
    #define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
    #define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
    #define CFG_ENV_SIZE		0x2000
#endif

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

#if defined(CFG_RAMBOOT)
  #if defined(CONFIG_PCI)
    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
				 | CFG_CMD_PING		\
				 | CFG_CMD_PCI		\
				 | CFG_CMD_I2C)		\
				&			\
				 ~(CFG_CMD_ENV		\
				  | CFG_CMD_IMLS	\
				  | CFG_CMD_FLASH	\
				  | CFG_CMD_LOADS))
  #else
    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
				 | CFG_CMD_PING		\
				 | CFG_CMD_I2C)		\
				&			\
				 ~(CFG_CMD_ENV		\
				 | CFG_CMD_IMLS		\
				 | CFG_CMD_FLASH	\
				 | CFG_CMD_LOADS))
  #endif
#else
  #if defined(CONFIG_PCI)
    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
				| CFG_CMD_PCI		\
				| CFG_CMD_PING		\
				| CFG_CMD_I2C)
  #else
    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
				| CFG_CMD_PING		\
				| CFG_CMD_I2C)
  #endif
#endif

#include <cmd_confdefs.h>

#undef CONFIG_WATCHDOG			/* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CFG_LONGHELP			/* undef to save memory	*/
#define CFG_LOAD_ADDR	0x2000000	/* default load address */
#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */

#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
    #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
#else
    #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
#endif

#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS	16		/* max number of command args */
#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/

/* Cache Configuration */
#define CFG_DCACHE_SIZE		32768
#define CFG_CACHELINE_SIZE	32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
#endif

/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM	0x02		/* Software reboot */

#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
#endif


/*
 * Environment Configuration
 */

/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_ETHADDR   00:E0:0C:00:00:01
#define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
#define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
#define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
#endif

#define CONFIG_HAS_ETH1		1
#define CONFIG_HAS_ETH2		1
#define CONFIG_HAS_ETH3		1

#define CONFIG_IPADDR	10.82.193.138

#define CONFIG_HOSTNAME		unknown
#define CONFIG_ROOTPATH		/opt/nfsroot
#define CONFIG_BOOTFILE		uImage

#define CONFIG_SERVERIP		192.168.1.1
#define CONFIG_GATEWAYIP	10.82.193.104
#define CONFIG_NETMASK		255.255.255.0

/* default location for tftp and bootm */
#define CONFIG_LOADADDR		1000000

#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
//#undef  CONFIG_BOOTARGS	/* the boot command will set bootargs */
#define CONFIG_BOOTARGS       "root=/dev/ram rw console=ttyS0,115200"

#define CONFIG_BAUDRATE	115200

#define	CONFIG_EXTRA_ENV_SETTINGS				        \
   "netdev=eth0\0"                                                      \
   "consoledev=ttyS0\0"                                                 \
   "ramdiskaddr=400000\0"						\
   "ramdiskfile=your.ramdisk.u-boot\0"                                  \
   "pex0=echo ---------------------------; echo --------- PCI EXPRESS -----\0"\
   "pexstat=mw f8008000 84000004; echo -expect:- 16000000; md f8008004 1\0" \
   "pex1=pci write 1.0.0 4 146; pci write 1.0.0 10 80000000\0" \
   "pexd=echo -expect:- xxx01002 00100146; pci display 1.0.0 0 2\0" \
   "pex=run pexstat; run pex1; run pexd\0" \
   "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
   "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
   "maxcpus=2"


#define CONFIG_NFSBOOTCOMMAND	                                        \
   "setenv bootargs root=/dev/nfs rw "                                  \
      "nfsroot=$serverip:$rootpath "                                    \
      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
      "console=$consoledev,$baudrate $othbootargs;"                     \
   "tftp $loadaddr $bootfile;"                                          \
   "bootm $loadaddr"

#define CONFIG_RAMBOOTCOMMAND \
   "setenv bootargs root=/dev/ram rw "                                  \
      "console=$consoledev,$baudrate $othbootargs;"                     \
   "tftp $ramdiskaddr $ramdiskfile;"                                    \
   "tftp $loadaddr $bootfile;"                                          \
   "bootm $loadaddr $ramdiskaddr"

#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND

#endif	/* __CONFIG_H */
Commit	Line	Data
5c9efb36 JL	1	/*
	2	* Copyright 2006 Freescale Semiconductor.
	3	*
debb7354 JL	4	* Srikanth Srinivasan ([email protected])
	5	*
	6	* See file CREDITS for list of people who contributed to this
	7	* project.
	8	*
	9	* This program is free software; you can redistribute it and/or
	10	* modify it under the terms of the GNU General Public License as
	11	* published by the Free Software Foundation; either version 2 of
	12	* the License, or (at your option) any later version.
	13	*
	14	* This program is distributed in the hope that it will be useful,
	15	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	16	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	17	* GNU General Public License for more details.
	18	*
	19	* You should have received a copy of the GNU General Public License
	20	* along with this program; if not, write to the Free Software
	21	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	22	* MA 02111-1307 USA
	23	*/
	24
	25	/*
5c9efb36	26	* MPC8641HPCN board configuration file
debb7354 JL	27	*
	28	* Make sure you change the MAC address and other network params first,
	29	* search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
	30	*/
	31
	32	#ifndef __CONFIG_H
	33	#define __CONFIG_H
	34
	35	/* High Level Configuration Options */
	36	#define CONFIG_MPC86xx 1 /* MPC86xx */
	37	#define CONFIG_MPC8641 1 /* MPC8641 specific */
	38	#define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */
	39	#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
	40	#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
5c9efb36	41	#undef DEBUG
debb7354	42
debb7354 JL	43	#ifdef RUN_DIAG
	44	#define CFG_DIAG_ADDR 0xff800000
	45	#endif
5c9efb36	46
debb7354 JL	47	#define CFG_RESET_ADDRESS 0xfff00100
debb7354 JL	48
5c9efb36 JL	49	#undef CONFIG_PCI
5c9efb36 JL	50
debb7354 JL	51	#define CONFIG_TSEC_ENET /* tsec ethernet support */
debb7354 JL	52	#define CONFIG_ENV_OVERWRITE
debb7354	53
5c9efb36 JL	54	#undef CONFIG_DDR_DLL /* possible DLL fix needed */
5c9efb36 JL	55	#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
debb7354 JL	56	#define CONFIG_DDR_ECC /* only for ECC DDR module */
	57	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
	58	#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
	59
5c9efb36	60	#define CONFIG_ALTIVEC 1
debb7354	61
5c9efb36	62	/*
debb7354 JL	63	* L2CR setup -- make sure this is right for your board!
debb7354 JL	64	*/
5c9efb36	65	#define CFG_L2
debb7354 JL	66	#define L2_INIT 0
	67	#define L2_ENABLE (L2CR_L2E)
	68
	69	#ifndef CONFIG_SYS_CLK_FREQ
debb7354 JL	70	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
	71	#endif
	72
debb7354 JL	73	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
	74
	75	#undef CFG_DRAM_TEST /* memory test, takes time */
	76	#define CFG_MEMTEST_START 0x00200000 /* memtest region */
	77	#define CFG_MEMTEST_END 0x00400000
	78
	79
	80	/*
	81	* Base addresses -- Note these are effective addresses where the
	82	* actual resources get mapped (not physical addresses)
	83	*/
	84	#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
	85	#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
	86	#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
	87
	88
	89	/*
	90	* DDR Setup
	91	*/
	92	#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
	93	#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
	94
	95	#define MPC86xx_DDR_SDRAM_CLK_CNTL
	96
	97	#if defined(CONFIG_SPD_EEPROM)
	98	/*
	99	* Determine DDR configuration from I2C interface.
	100	*/
	101	#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
	102
	103	#else
	104	/*
	105	* Manually set up DDR parameters
	106	*/
	107
	108	/* DDR I */
	109	#if 1
	110	#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
	111
	112	#define CFG_DDR_CS0_BNDS 0x0000000F
	113	#define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
	114	#define CFG_DDR_EXT_REFRESH 0x00000000
	115	#define CFG_DDR_TIMING_0 0x00260802
	116	#define CFG_DDR_TIMING_1 0x39357322
	117	#define CFG_DDR_TIMING_2 0x14904cc8
	118	#define CFG_DDR_MODE_1 0x00480432
	119	#define CFG_DDR_MODE_2 0x00000000
	120	#define CFG_DDR_INTERVAL 0x06090100
	121	#define CFG_DDR_DATA_INIT 0xdeadbeef
	122	#define CFG_DDR_CLK_CTRL 0x03800000
5c9efb36 JL	123	#define CFG_DDR_OCD_CTRL 0x00000000
5c9efb36 JL	124	#define CFG_DDR_OCD_STATUS 0x00000000
debb7354	125	#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
5c9efb36	126	#define CFG_DDR_CONTROL2 0x04400000
debb7354 JL	127
	128	//Not used in fixed_sdram function
	129
	130	#define CFG_DDR_MODE 0x00000022
	131	#define CFG_DDR_CS1_BNDS 0x00000000
	132	#define CFG_DDR_CS2_BNDS 0x00000FFF //Not done
	133	#define CFG_DDR_CS3_BNDS 0x00000FFF //Not done
	134	#define CFG_DDR_CS4_BNDS 0x00000FFF //Not done
	135	#define CFG_DDR_CS5_BNDS 0x00000FFF //Not done
debb7354 JL	136	#endif
	137	#endif
	138
	139
	140	/*
5c9efb36	141	* In MPC8641HPCN, we allocate 16MB flash spaces at fe000000 and ff000000
debb7354 JL	142	* We only have an 8MB flash. In effect, the addresses from fe000000 to fe7fffff
	143	* map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff.
	144	* However, when u-boot comes up, the flash_init needs hard start addresses
	145	* to build its info table. For user convenience, we have the flash addresses
	146	* as fe800000 and ff800000. That way, when we do flash operations, u-boot
	147	* knows where the flash is and the user can download u-boot code from promjet to
	148	* fef00000 <- more intuitive than fe700000. Note that, on switching the boot
	149	* location, fef00000 becomes fff00000.
5c9efb36	150	*/
debb7354	151	#define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */
5c9efb36	152	#define CFG_FLASH_BASE2 0xff800000
debb7354 JL	153
	154	#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
	155
debb7354 JL	156	#define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */
	157	#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Boot Flash area*/
	158
	159	#define CFG_BR1_PRELIM 0xfe001001 /* port size 16bit */
	160	#define CFG_OR1_PRELIM 0xff006ff7 /* 16MB Alternate Boot Flash area*/
	161
	162	#define CFG_BR2_PRELIM 0xf8201001 /* port size 16bit */
	163	#define CFG_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/
	164
	165	#define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */
	166	#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
	167
debb7354	168
5c9efb36 JL	169	#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
	170	#define PIXIS_ID 0x0 /* Board ID at offset 0 */
	171	#define PIXIS_VER 0x1 /* Board version at offset 1 */
	172	#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
	173	#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
	174	#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */
	175	#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
	176	#define PIXIS_VCTL 0x10 /* VELA Control Register */
	177	#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
	178	#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
	179	#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
	180	#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
	181	#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
	182	#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
	183	#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
debb7354 JL	184
debb7354 JL	185	#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
debb7354 JL	186	#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
	187
	188	#undef CFG_FLASH_CHECKSUM
	189	#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	190	#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
	191	#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
	192
debb7354 JL	193	#define CFG_FLASH_CFI
	194	#define CFG_FLASH_EMPTY_INFO
	195
debb7354 JL	196	#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
	197	#define CFG_RAMBOOT
	198	#else
	199	#undef CFG_RAMBOOT
	200	#endif
	201
	202	#if !defined(CFG_RAMBOOT)
	203	#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
	204	#endif
	205
	206	#undef CONFIG_CLOCKS_IN_MHZ
	207
	208	#define CONFIG_L1_INIT_RAM
5c9efb36	209	#undef CFG_INIT_RAM_LOCK
debb7354 JL	210	#ifndef CFG_INIT_RAM_LOCK
	211	#define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
	212	#else
	213	#define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
	214	#endif
	215	#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
	216
	217	#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
	218	#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
	219	#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
	220
	221	#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	222	#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
	223
	224	/* Serial Port */
	225	#define CONFIG_CONS_INDEX 1
	226	#undef CONFIG_SERIAL_SOFTWARE_FIFO
	227	#define CFG_NS16550
	228	#define CFG_NS16550_SERIAL
	229	#define CFG_NS16550_REG_SIZE 1
	230	#define CFG_NS16550_CLK get_bus_freq(0)
	231
	232	#define CFG_BAUDRATE_TABLE \
	233	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
	234
	235	#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
	236	#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
	237
	238	/* Use the HUSH parser */
	239	#define CFG_HUSH_PARSER
	240	#ifdef CFG_HUSH_PARSER
	241	#define CFG_PROMPT_HUSH_PS2 "> "
	242	#endif
	243
5c9efb36 JL	244	/*
	245	* Pass open firmware flat tree to kernel
	246	*/
	247	#define CONFIG_OF_FLAT_TREE 1
	248	#define CONFIG_OF_BOARD_SETUP 1
debb7354 JL	249
debb7354 JL	250	/* maximum size of the flat tree (8K) */
5c9efb36	251	#define OF_FLAT_TREE_MAX_SIZE 8192
debb7354	252
5c9efb36 JL	253	#define OF_CPU "PowerPC,8641@0"
	254	#define OF_SOC "soc8641@f8000000"
	255	#define OF_TBCLK (bd->bi_busfreq / 8)
	256	#define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500"
debb7354	257
5c9efb36 JL	258	#define CFG_64BIT_VSPRINTF 1
5c9efb36 JL	259	#define CFG_64BIT_STRTOUL 1
debb7354 JL	260
	261	/* I2C */
	262	#define CONFIG_HARD_I2C /* I2C with hardware support*/
	263	#undef CONFIG_SOFT_I2C /* I2C bit-banged */
	264	#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
	265	#define CFG_I2C_SLAVE 0x7F
	266	#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
	267
	268	/* RapidIO MMU */
	269	#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
	270	#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
	271	#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
	272
	273	/*
	274	* General PCI
	275	* Addresses are mapped 1-1.
	276	*/
	277	#define CFG_PCI1_MEM_BASE 0x80000000
debb7354 JL	278	#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
	279	#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
	280	#define CFG_PCI1_IO_BASE 0xe2000000
debb7354	281	#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
debb7354 JL	282	#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
	283
	284	/* For RTL8139 */
	285	#define _IO_BASE 0x00000000
	286
	287	#define CFG_PCI2_MEM_BASE 0xa0000000
	288	#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
	289	#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
	290	#define CFG_PCI2_IO_BASE 0xe3000000
	291	#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
	292	#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
	293
debb7354 JL	294
	295	#if defined(CONFIG_PCI)
	296
debb7354 JL	297	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
debb7354 JL	298
5c9efb36	299	#undef CFG_SCSI_SCAN_BUS_REVERSE
debb7354 JL	300
	301	#define CONFIG_NET_MULTI
	302	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	303
	304	#define CONFIG_RTL8139
	305
debb7354 JL	306	#undef CONFIG_EEPRO100
	307	#undef CONFIG_TULIP
	308
	309	#if !defined(CONFIG_PCI_PNP)
	310	#define PCI_ENET0_IOADDR 0xe0000000
	311	#define PCI_ENET0_MEMADDR 0xe0000000
	312	#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
	313	#endif
	314
	315	#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
debb7354 JL	316
	317	#endif /* CONFIG_PCI */
	318
	319
	320	#if defined(CONFIG_TSEC_ENET)
	321
	322	#ifndef CONFIG_NET_MULTI
	323	#define CONFIG_NET_MULTI 1
	324	#endif
	325
	326	#define CONFIG_MII 1 /* MII PHY management */
	327
	328	#define CONFIG_MPC86XX_TSEC1 1
	329	#define CONFIG_MPC86XX_TSEC1_NAME "eTSEC1"
	330	#define CONFIG_MPC86XX_TSEC2 1
	331	#define CONFIG_MPC86XX_TSEC2_NAME "eTSEC2"
	332	#define CONFIG_MPC86XX_TSEC3 1
	333	#define CONFIG_MPC86XX_TSEC3_NAME "eTSEC3"
	334	#define CONFIG_MPC86XX_TSEC4 1
	335	#define CONFIG_MPC86XX_TSEC4_NAME "eTSEC4"
	336
debb7354 JL	337	#define TSEC1_PHY_ADDR 0
	338	#define TSEC2_PHY_ADDR 1
	339	#define TSEC3_PHY_ADDR 2
	340	#define TSEC4_PHY_ADDR 3
	341	#define TSEC1_PHYIDX 0
	342	#define TSEC2_PHYIDX 0
	343	#define TSEC3_PHYIDX 0
	344	#define TSEC4_PHYIDX 0
	345
	346	#define CONFIG_ETHPRIME "eTSEC1"
	347
	348	#endif /* CONFIG_TSEC_ENET */
	349
	350
	351	/* BAT0 2G Cacheable, non-guarded
	352	* 0x0000_0000 2G DDR
	353	*/
5c9efb36 JL	354	#define CFG_DBAT0L ( BATL_PP_RW \| BATL_CACHEINHIBIT \
	355	\| BATL_GUARDEDSTORAGE \| BATL_MEMCOHERENCE )
	356	#define CFG_DBAT0U ( BATU_BL_512M \| BATU_VS \| BATU_VP )
	357	#define CFG_IBAT0L ( BATL_PP_RW \| BATL_CACHEINHIBIT \| BATL_MEMCOHERENCE)
debb7354 JL	358	#define CFG_IBAT0U CFG_DBAT0U
	359
	360	/* BAT1 1G Cache-inhibited, guarded
	361	* 0x8000_0000 512M PCI-Express 1 Memory
	362	* 0xa000_0000 512M PCI-Express 2 Memory
	363	** SS - Changed it for operating from 0xd0000000
	364	*/
5c9efb36 JL	365	#define CFG_DBAT1L ( CFG_PCI1_MEM_BASE \| BATL_PP_RW \
5c9efb36 JL	366	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
debb7354 JL	367	#define CFG_DBAT1U (CFG_PCI1_MEM_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	368	#define CFG_IBAT1L (CFG_PCI1_MEM_BASE \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	369	#define CFG_IBAT1U CFG_DBAT1U
	370
	371	/* BAT2 512M Cache-inhibited, guarded
	372	* 0xc000_0000 512M RapidIO Memory
	373	*/
5c9efb36 JL	374	#define CFG_DBAT2L (CFG_RIO_MEM_BASE \| BATL_PP_RW \
5c9efb36 JL	375	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
debb7354 JL	376	#define CFG_DBAT2U (CFG_RIO_MEM_BASE \| BATU_BL_512M \| BATU_VS \| BATU_VP)
	377	#define CFG_IBAT2L (CFG_RIO_MEM_BASE \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	378	#define CFG_IBAT2U CFG_DBAT2U
	379
	380	/* BAT3 4M Cache-inhibited, guarded
	381	* 0xf800_0000 4M CCSR
	382	*/
5c9efb36 JL	383	#define CFG_DBAT3L ( CFG_CCSRBAR \| BATL_PP_RW \
5c9efb36 JL	384	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
debb7354 JL	385	#define CFG_DBAT3U (CFG_CCSRBAR \| BATU_BL_4M \| BATU_VS \| BATU_VP)
	386	#define CFG_IBAT3L (CFG_CCSRBAR \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	387	#define CFG_IBAT3U CFG_DBAT3U
	388
	389	/* BAT4 32M Cache-inhibited, guarded
	390	* 0xe200_0000 16M PCI-Express 1 I/O
	391	* 0xe300_0000 16M PCI-Express 2 I/0
	392	** SS - Note that this is at 0xe0000000
	393	*/
5c9efb36 JL	394	#define CFG_DBAT4L ( CFG_PCI1_IO_BASE \| BATL_PP_RW \
5c9efb36 JL	395	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
debb7354 JL	396	#define CFG_DBAT4U (CFG_PCI1_IO_BASE \| BATU_BL_32M \| BATU_VS \| BATU_VP)
	397	#define CFG_IBAT4L (CFG_PCI1_IO_BASE \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	398	#define CFG_IBAT4U CFG_DBAT4U
	399
	400	/* BAT5 128K Cacheable, non-guarded
	401	* 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
	402	*/
	403	#define CFG_DBAT5L (CFG_INIT_RAM_ADDR \| BATL_PP_RW \| BATL_MEMCOHERENCE)
	404	#define CFG_DBAT5U (CFG_INIT_RAM_ADDR \| BATU_BL_128K \| BATU_VS \| BATU_VP)
	405	#define CFG_IBAT5L CFG_DBAT5L
	406	#define CFG_IBAT5U CFG_DBAT5U
	407
	408	/* BAT6 32M Cache-inhibited, guarded
	409	* 0xfe00_0000 32M FLASH
	410	*/
5c9efb36 JL	411	#define CFG_DBAT6L ( CFG_FLASH_BASE \| BATL_PP_RW \
5c9efb36 JL	412	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
debb7354 JL	413	#define CFG_DBAT6U (CFG_FLASH_BASE \| BATU_BL_32M \| BATU_VS \| BATU_VP)
	414	#define CFG_IBAT6L (CFG_FLASH_BASE \| BATL_PP_RW \| BATL_MEMCOHERENCE)
	415	#define CFG_IBAT6U CFG_DBAT6U
	416
debb7354 JL	417	#define CFG_DBAT7L 0x00000000
	418	#define CFG_DBAT7U 0x00000000
	419	#define CFG_IBAT7L 0x00000000
	420	#define CFG_IBAT7U 0x00000000
	421
	422
	423
	424
	425	/*
	426	* Environment
	427	*/
5c9efb36 JL	428	#ifndef CFG_RAMBOOT
	429	#define CFG_ENV_IS_IN_FLASH 1
	430	#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
	431	#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
	432	#define CFG_ENV_SIZE 0x2000
	433	#else
	434	#define CFG_NO_FLASH 1 /* Flash is not usable now */
	435	#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
	436	#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
	437	#define CFG_ENV_SIZE 0x2000
	438	#endif
debb7354 JL	439
	440	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	441	#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
	442
	443	#if defined(CFG_RAMBOOT)
	444	#if defined(CONFIG_PCI)
	445	#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
	446	\| CFG_CMD_PING \
	447	\| CFG_CMD_PCI \
	448	\| CFG_CMD_I2C) \
	449	& \
	450	~(CFG_CMD_ENV \
	451	\| CFG_CMD_IMLS \
	452	\| CFG_CMD_FLASH \
	453	\| CFG_CMD_LOADS))
	454	#else
	455	#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
	456	\| CFG_CMD_PING \
	457	\| CFG_CMD_I2C) \
	458	& \
	459	~(CFG_CMD_ENV \
	460	\| CFG_CMD_IMLS \
	461	\| CFG_CMD_FLASH \
	462	\| CFG_CMD_LOADS))
	463	#endif
	464	#else
	465	#if defined(CONFIG_PCI)
	466	#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
	467	\| CFG_CMD_PCI \
	468	\| CFG_CMD_PING \
	469	\| CFG_CMD_I2C)
	470	#else
	471	#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
	472	\| CFG_CMD_PING \
	473	\| CFG_CMD_I2C)
	474	#endif
	475	#endif
	476
	477	#include <cmd_confdefs.h>
	478
	479	#undef CONFIG_WATCHDOG /* watchdog disabled */
	480
	481	/*
	482	* Miscellaneous configurable options
	483	*/
	484	#define CFG_LONGHELP /* undef to save memory */
	485	#define CFG_LOAD_ADDR 0x2000000 /* default load address */
	486	#define CFG_PROMPT "=> " /* Monitor Command Prompt */
	487
	488	#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
	489	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
	490	#else
	491	#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
	492	#endif
	493
	494	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	495	#define CFG_MAXARGS 16 /* max number of command args */
	496	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
	497	#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
	498
	499	/*
	500	* For booting Linux, the board info and command line data
	501	* have to be in the first 8 MB of memory, since this is
	502	* the maximum mapped by the Linux kernel during initialization.
503	*/
504	#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
505
506	/* Cache Configuration */
507	#define CFG_DCACHE_SIZE 32768
508	#define CFG_CACHELINE_SIZE 32
509	#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
510	#define CFG_CACHELINE_SHIFT 5 /log base 2 of the above value/
511	#endif
512
513	/*
514	* Internal Definitions
515	*
516	* Boot Flags
517	*/
518	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
519	#define BOOTFLAG_WARM 0x02 /* Software reboot */
520
521	#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
522	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
523	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
524	#endif
525
526
527	/*
528	* Environment Configuration
529	*/
530
531	/* The mac addresses for all ethernet interface */
532	#if defined(CONFIG_TSEC_ENET)
533	#define CONFIG_ETHADDR 00:E0:0C:00:00:01
534	#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
535	#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
536	#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
537	#endif
538
5c9efb36 JL	539	#define CONFIG_HAS_ETH1 1
	540	#define CONFIG_HAS_ETH2 1
	541	#define CONFIG_HAS_ETH3 1
debb7354	542
5c9efb36	543	#define CONFIG_IPADDR 10.82.193.138
debb7354 JL	544
	545	#define CONFIG_HOSTNAME unknown
	546	#define CONFIG_ROOTPATH /opt/nfsroot
	547	#define CONFIG_BOOTFILE uImage
	548
5c9efb36 JL	549	#define CONFIG_SERVERIP 192.168.1.1
	550	#define CONFIG_GATEWAYIP 10.82.193.104
	551	#define CONFIG_NETMASK 255.255.255.0
debb7354	552
5c9efb36 JL	553	/* default location for tftp and bootm */
5c9efb36 JL	554	#define CONFIG_LOADADDR 1000000
debb7354 JL	555
debb7354 JL	556	#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
5c9efb36	557	//#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
debb7354 JL	558	#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"
	559
	560	#define CONFIG_BAUDRATE 115200
	561
	562	#define CONFIG_EXTRA_ENV_SETTINGS \
	563	"netdev=eth0\0" \
	564	"consoledev=ttyS0\0" \
	565	"ramdiskaddr=400000\0" \
	566	"ramdiskfile=your.ramdisk.u-boot\0" \
5c9efb36	567	"pex0=echo ---------------------------; echo --------- PCI EXPRESS -----\0"\
debb7354 JL	568	"pexstat=mw f8008000 84000004; echo -expect:- 16000000; md f8008004 1\0" \
	569	"pex1=pci write 1.0.0 4 146; pci write 1.0.0 10 80000000\0" \
	570	"pexd=echo -expect:- xxx01002 00100146; pci display 1.0.0 0 2\0" \
	571	"pex=run pexstat; run pex1; run pexd\0" \
	572	"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
	573	"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
	574	"maxcpus=2"
	575
	576
	577	#define CONFIG_NFSBOOTCOMMAND \
	578	"setenv bootargs root=/dev/nfs rw " \
	579	"nfsroot=$serverip:$rootpath " \
	580	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	581	"console=$consoledev,$baudrate $othbootargs;" \
	582	"tftp $loadaddr $bootfile;" \
	583	"bootm $loadaddr"
	584
	585	#define CONFIG_RAMBOOTCOMMAND \
	586	"setenv bootargs root=/dev/ram rw " \
	587	"console=$consoledev,$baudrate $othbootargs;" \
	588	"tftp $ramdiskaddr $ramdiskfile;" \
	589	"tftp $loadaddr $bootfile;" \
	590	"bootm $loadaddr $ramdiskaddr"
	591
	592	#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
	593
	594	#endif /* __CONFIG_H */