[J-u-boot.git] / include / configs / acadia.h

/*
 * (C) Copyright 2007
 * Stefan Roese, DENX Software Engineering, [email protected].
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/************************************************************************
 * acadia.h - configuration for AMCC Acadia (405EZ)
 ***********************************************************************/

#ifndef __CONFIG_H
#define __CONFIG_H

/*-----------------------------------------------------------------------
 * High Level Configuration Options
 *----------------------------------------------------------------------*/
#define CONFIG_ACADIA		1		/* Board is Acadia	*/
#define CONFIG_4xx		1		/* ... PPC4xx family	*/
#define CONFIG_405EZ		1		/* Specifc 405EZ support*/

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE	0xFFF80000
#endif

/*
 * Include common defines/options for all AMCC eval boards
 */
#define CONFIG_HOSTNAME		acadia
#include "amcc-common.h"

/* Detect Acadia PLL input clock automatically via CPLD bit		*/
#define CONFIG_SYS_CLK_FREQ    ((in8(CONFIG_SYS_CPLD_BASE + 0) == 0x0c) ? \
				66666666 : 33333000)

#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
#define CONFIG_MISC_INIT_F	1		/* Call misc_init_f	*/

#define CONFIG_NO_SERIAL_EEPROM
/*#undef CONFIG_NO_SERIAL_EEPROM*/

#ifdef CONFIG_NO_SERIAL_EEPROM
/*----------------------------------------------------------------------------
 * PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI,
 * assuming a 66MHz input clock to the 405EZ.
 *---------------------------------------------------------------------------*/
/* #define PLLMR0_100_100_12 */
#define PLLMR0_200_133_66
/* #define PLLMR0_266_160_80 */
/* #define PLLMR0_333_166_83 */
#endif

/*-----------------------------------------------------------------------
 * Base addresses -- Note these are effective addresses where the
 * actual resources get mapped (not physical addresses)
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_BASE		0xfe000000
#define CONFIG_SYS_CPLD_BASE		0x80000000
#define CONFIG_SYS_NAND_ADDR		0xd0000000
#define CONFIG_SYS_USB_HOST		0xef603000	/* USB OHCI 1.1 controller	*/

/*-----------------------------------------------------------------------
 * Initial RAM & stack pointer
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_TEMP_STACK_OCM	1		/* OCM as init ram	*/

/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR	0xf8000000
#define CONFIG_SYS_OCM_DATA_SIZE	0x4000			/* 16K of onchip SRAM		*/
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR	/* inside of SRAM		*/
#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE	/* Size of used area in RAM	*/

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Serial Port
 *----------------------------------------------------------------------*/
#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
#undef	CONFIG_SYS_EXT_SERIAL_CLOCK			/* external serial clock */
#define CONFIG_SYS_BASE_BAUD		691200

/*-----------------------------------------------------------------------
 * Environment
 *----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
#else
#define CONFIG_ENV_IS_IN_NAND	1	/* use NAND for environment vars	*/
#define CONFIG_ENV_IS_EMBEDDED	1	/* use embedded environment */
#endif

/*-----------------------------------------------------------------------
 * FLASH related
 *----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_FLASH_CFI			/* The flash is CFI compatible	*/
#define CONFIG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/

#define CONFIG_SYS_FLASH_BANKS_LIST    {CONFIG_SYS_FLASH_BASE}
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */

#else
/*
 * No NOR-flash on Acadia when NAND-booting. We need to undef the
 * NOR device-tree fixup code as well, since flash_info is not defined
 * in this case.
 */
#define	CONFIG_SYS_NO_FLASH		1
#undef CONFIG_FDT_FIXUP_NOR_FLASH_SIZE
#endif

#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE	0x40000 /* size of one complete sector	*/
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
#endif

/*
 * IPL (Initial Program Loader, integrated inside CPU)
 * Will load first 4k from NAND (SPL) into cache and execute it from there.
 *
 * SPL (Secondary Program Loader)
 * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
 * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
 * controller and the NAND controller so that the special U-Boot image can be
 * loaded from NAND to SDRAM.
 *
 * NUB (NAND U-Boot)
 * This NAND U-Boot (NUB) is a special U-Boot version which can be started
 * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
 *
 * On 440EPx the SPL is copied to SDRAM before the NAND controller is
 * set up. While still running from cache, I experienced problems accessing
 * the NAND controller.	sr - 2006-08-25
 */
#define CONFIG_SYS_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location			*/
#define CONFIG_SYS_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size			*/
#define CONFIG_SYS_NAND_BOOT_SPL_DST	(CONFIG_SYS_OCM_DATA_ADDR + (16 << 10)) /* Copy SPL here*/
#define CONFIG_SYS_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr	*/
#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr	*/
#define CONFIG_SYS_NAND_BOOT_SPL_DELTA	(CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)

/*
 * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
 */
#define CONFIG_SYS_NAND_U_BOOT_OFFS	(16 << 10)	/* Offset to RAM U-Boot image	*/
#define CONFIG_SYS_NAND_U_BOOT_SIZE	(384 << 10)	/* Size of RAM U-Boot image	*/

/*
 * Now the NAND chip has to be defined (no autodetection used!)
 */
#define CONFIG_SYS_NAND_PAGE_SIZE	512		/* NAND chip page size		*/
#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 << 10)	/* NAND chip block size		*/
#define CONFIG_SYS_NAND_PAGE_COUNT	32		/* NAND chip page count		*/
#define CONFIG_SYS_NAND_BAD_BLOCK_POS	5		/* Location of bad block marker	*/
#undef CONFIG_SYS_NAND_4_ADDR_CYCLE			/* No fourth addr used (<=32MB)	*/

#define CONFIG_SYS_NAND_ECCSIZE	256
#define CONFIG_SYS_NAND_ECCBYTES	3
#define CONFIG_SYS_NAND_OOBSIZE	16
#define CONFIG_SYS_NAND_ECCPOS		{0, 1, 2, 3, 6, 7}

#ifdef CONFIG_ENV_IS_IN_NAND
/*
 * For NAND booting the environment is embedded in the U-Boot image. Please take
 * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
 */
#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
#define CONFIG_ENV_OFFSET		(CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#endif

/*-----------------------------------------------------------------------
 * RAM (CRAM)
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_MBYTES_RAM		64		/* 64MB			*/

/*-----------------------------------------------------------------------
 * I2C
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000

#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10

/* I2C SYSMON (LM75, AD7414 is almost compatible)			*/
#define CONFIG_DTT_LM75		1		/* ON Semi's LM75	*/
#define CONFIG_DTT_AD7414	1		/* use AD7414		*/
#define CONFIG_DTT_SENSORS	{0}		/* Sensor addresses	*/
#define CONFIG_SYS_DTT_MAX_TEMP	70
#define CONFIG_SYS_DTT_LOW_TEMP	-30
#define CONFIG_SYS_DTT_HYSTERESIS	3

/*-----------------------------------------------------------------------
 * Ethernet
 *----------------------------------------------------------------------*/
#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
#define CONFIG_HAS_ETH0		1

/*
 * Default environment variables
 */
#define	CONFIG_EXTRA_ENV_SETTINGS					\
	CONFIG_AMCC_DEF_ENV						\
	CONFIG_AMCC_DEF_ENV_POWERPC					\
	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
	"kernel_addr=fff10000\0"					\
	"ramdisk_addr=fff20000\0"					\
	"kozio=bootm ffc60000\0"					\
	""

#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE

/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION

#define CONFIG_SUPPORT_VFAT

/*
 * Commands additional to the ones defined in amcc-common.h
 */
#define CONFIG_CMD_DTT
#define CONFIG_CMD_NAND
#define CONFIG_CMD_USB

/*
 * No NOR on Acadia when NAND-booting
 */
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
#undef CONFIG_CMD_FLASH
#undef CONFIG_CMD_IMLS
#endif

/*-----------------------------------------------------------------------
 * NAND FLASH
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		(CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
#define CONFIG_SYS_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/

/*-----------------------------------------------------------------------
 * External Bus Controller (EBC) Setup
 *----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_NAND_CS		3
/* Memory Bank 0 (Flash) initialization						*/
#define CONFIG_SYS_EBC_PB0AP		0x03337200
#define CONFIG_SYS_EBC_PB0CR		0xfe0bc000

/* Memory Bank 3 (NAND-FLASH) initialization					*/
#define CONFIG_SYS_EBC_PB3AP		0x018003c0
#define CONFIG_SYS_EBC_PB3CR		(CONFIG_SYS_NAND_ADDR | 0x1c000)

/* Just initial configuration for CRAM. Will be changed in memory.c to sync mode*/
/* Memory Bank 1 (CRAM) initialization						*/
#define CONFIG_SYS_EBC_PB1AP		0x030400c0
#define CONFIG_SYS_EBC_PB1CR		0x000bc000

/* Memory Bank 2 (CRAM) initialization						*/
#define CONFIG_SYS_EBC_PB2AP		0x030400c0
#define CONFIG_SYS_EBC_PB2CR		0x020bc000
#else
#define CONFIG_SYS_NAND_CS		0		/* NAND chip connected to CSx	*/
/* Memory Bank 0 (NAND-FLASH) initialization					*/
#define CONFIG_SYS_EBC_PB0AP		0x018003c0
#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_NAND_ADDR | 0x1c000)

/*
 * When NAND-booting the CRAM EBC setup must be done in sync mode, since the
 * NAND-SPL already initialized the CRAM and EBC to sync mode.
 */
/* Memory Bank 1 (CRAM) initialization						*/
#define CONFIG_SYS_EBC_PB1AP		0x9C0201C0
#define CONFIG_SYS_EBC_PB1CR		0x000bc000

/* Memory Bank 2 (CRAM) initialization						*/
#define CONFIG_SYS_EBC_PB2AP		0x9C0201C0
#define CONFIG_SYS_EBC_PB2CR		0x020bc000
#endif

/* Memory Bank 4 (CPLD) initialization						*/
#define CONFIG_SYS_EBC_PB4AP		0x04006000
#define CONFIG_SYS_EBC_PB4CR		(CONFIG_SYS_CPLD_BASE | 0x18000)

#define CONFIG_SYS_EBC_CFG		0xf8400000

/*-----------------------------------------------------------------------
 * GPIO Setup
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_GPIO_CRAM_CLK	8
#define CONFIG_SYS_GPIO_CRAM_WAIT	9		/* GPIO-In		*/
#define CONFIG_SYS_GPIO_CRAM_ADV	10
#define CONFIG_SYS_GPIO_CRAM_CRE	(32 + 21)	/* GPIO-Out		*/

/*-----------------------------------------------------------------------
 * Definitions for GPIO_0 setup (PPC405EZ specific)
 *
 * GPIO0[0-2]	- External Bus Controller CS_4 - CS_6 Outputs
 * GPIO0[3]	- NAND FLASH Controller CE3 (NFCE3) Output
 * GPIO0[4]	- External Bus Controller Hold Input
 * GPIO0[5]	- External Bus Controller Priority Input
 * GPIO0[6]	- External Bus Controller HLDA Output
 * GPIO0[7]	- External Bus Controller Bus Request Output
 * GPIO0[8]	- CRAM Clk Output
 * GPIO0[9]	- External Bus Controller Ready Input
 * GPIO0[10]	- CRAM Adv Output
 * GPIO0[11-24]	- NAND Flash Control Data -> Bypasses GPIO when enabled
 * GPIO0[25]	- External DMA Request Input
 * GPIO0[26]	- External DMA EOT I/O
 * GPIO0[25]	- External DMA Ack_n Output
 * GPIO0[17-23]	- External Interrupts IRQ0 - IRQ6 inputs
 * GPIO0[28-30]	- Trace Outputs / PWM Inputs
 * GPIO0[31]	- PWM_8 I/O
 */
#define CONFIG_SYS_GPIO0_TCR		0xC0A00000
#define CONFIG_SYS_GPIO0_OSRL		0x50004400
#define CONFIG_SYS_GPIO0_OSRH		0x02000055
#define CONFIG_SYS_GPIO0_ISR1L		0x00001000
#define CONFIG_SYS_GPIO0_ISR1H		0x00000055
#define CONFIG_SYS_GPIO0_TSRL		0x02000000
#define CONFIG_SYS_GPIO0_TSRH		0x00000055

/*-----------------------------------------------------------------------
 * Definitions for GPIO_1 setup (PPC405EZ specific)
 *
 * GPIO1[0-6]	- PWM_9 to PWM_15 I/O
 * GPIO1[7]	- PWM_DIV_CLK (Out) / IRQ4 Input
 * GPIO1[8]	- TS5 Output / DAC_IP_TRIG Input
 * GPIO1[9]	- TS6 Output / ADC_IP_TRIG Input
 * GPIO1[10-12]	- UART0 Control Inputs
 * GPIO1[13]	- UART0_DTR_N Output/IEEE_1588_TS Output/TMRCLK Input
 * GPIO1[14]	- UART0_RTS_N Output/SPI_SS_2_N Output
 * GPIO1[15]	- SPI_SS_3_N Output/UART0_RI_N Input
 * GPIO1[16]	- SPI_SS_1_N Output
 * GPIO1[17-20]	- Trace Output/External Interrupts IRQ0 - IRQ3 inputs
 */
#define CONFIG_SYS_GPIO1_TCR		0xFFFF8414
#define CONFIG_SYS_GPIO1_OSRL		0x40000110
#define CONFIG_SYS_GPIO1_OSRH		0x55455555
#define CONFIG_SYS_GPIO1_ISR1L		0x15555445
#define CONFIG_SYS_GPIO1_ISR1H		0x00000000
#define CONFIG_SYS_GPIO1_TSRL		0x00000000
#define CONFIG_SYS_GPIO1_TSRH		0x00000000

#endif	/* __CONFIG_H */
Commit	Line	Data
16c0cc1c SR	1	/*
	2	* (C) Copyright 2007
	3	* Stefan Roese, DENX Software Engineering, [email protected].
	4	*
3765b3e7	5	* SPDX-License-Identifier: GPL-2.0+
16c0cc1c SR	6	*/
	7
	8	/************************************************************************
	9	* acadia.h - configuration for AMCC Acadia (405EZ)
	10	***********************************************************************/
	11
	12	#ifndef __CONFIG_H
	13	#define __CONFIG_H
	14
	15	/*-----------------------------------------------------------------------
	16	* High Level Configuration Options
	17	----------------------------------------------------------------------/
3cb86f3e SR	18	#define CONFIG_ACADIA 1 /* Board is Acadia */
	19	#define CONFIG_4xx 1 /* ... PPC4xx family */
	20	#define CONFIG_405EZ 1 /* Specifc 405EZ support*/
490f2040	21
2ae18241 WD	22	#ifndef CONFIG_SYS_TEXT_BASE
	23	#define CONFIG_SYS_TEXT_BASE 0xFFF80000
	24	#endif
	25
490f2040 SR	26	/*
	27	* Include common defines/options for all AMCC eval boards
	28	*/
	29	#define CONFIG_HOSTNAME acadia
	30	#include "amcc-common.h"
	31
5d4a1790	32	/* Detect Acadia PLL input clock automatically via CPLD bit */
6d0f6bcf	33	#define CONFIG_SYS_CLK_FREQ ((in8(CONFIG_SYS_CPLD_BASE + 0) == 0x0c) ? \
5d4a1790	34	66666666 : 33333000)
16c0cc1c	35
3cb86f3e SR	36	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
3cb86f3e SR	37	#define CONFIG_MISC_INIT_F 1 /* Call misc_init_f */
16c0cc1c SR	38
	39	#define CONFIG_NO_SERIAL_EEPROM
	40	/#undef CONFIG_NO_SERIAL_EEPROM/
	41
	42	#ifdef CONFIG_NO_SERIAL_EEPROM
16c0cc1c SR	43	/*----------------------------------------------------------------------------
	44	* PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI,
	45	* assuming a 66MHz input clock to the 405EZ.
	46	---------------------------------------------------------------------------/
	47	/* #define PLLMR0_100_100_12 */
	48	#define PLLMR0_200_133_66
	49	/* #define PLLMR0_266_160_80 */
	50	/* #define PLLMR0_333_166_83 */
	51	#endif
	52
	53	/*-----------------------------------------------------------------------
	54	* Base addresses -- Note these are effective addresses where the
	55	* actual resources get mapped (not physical addresses)
	56	----------------------------------------------------------------------/
6d0f6bcf JCPV	57	#define CONFIG_SYS_FLASH_BASE 0xfe000000
	58	#define CONFIG_SYS_CPLD_BASE 0x80000000
	59	#define CONFIG_SYS_NAND_ADDR 0xd0000000
	60	#define CONFIG_SYS_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */
16c0cc1c	61
3cb86f3e SR	62	/*-----------------------------------------------------------------------
	63	* Initial RAM & stack pointer
	64	----------------------------------------------------------------------/
6d0f6bcf	65	#define CONFIG_SYS_TEMP_STACK_OCM 1 /* OCM as init ram */
3cb86f3e SR	66
3cb86f3e SR	67	/* On Chip Memory location */
6d0f6bcf JCPV	68	#define CONFIG_SYS_OCM_DATA_ADDR 0xf8000000
	69	#define CONFIG_SYS_OCM_DATA_SIZE 0x4000 /* 16K of onchip SRAM */
	70	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SRAM */
553f0982	71	#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
3cb86f3e	72
25ddd1fb	73	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
6d0f6bcf	74	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
3cb86f3e SR	75
	76	/*-----------------------------------------------------------------------
	77	* Serial Port
	78	----------------------------------------------------------------------/
550650dd	79	#define CONFIG_CONS_INDEX 1 /* Use UART0 */
6d0f6bcf JCPV	80	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
6d0f6bcf JCPV	81	#define CONFIG_SYS_BASE_BAUD 691200
3cb86f3e SR	82
	83	/*-----------------------------------------------------------------------
	84	* Environment
	85	----------------------------------------------------------------------/
16c0cc1c	86	#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
5a1aceb0	87	#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
16c0cc1c	88	#else
51bfee19	89	#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
0e8d1586	90	#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
16c0cc1c SR	91	#endif
16c0cc1c SR	92
3cb86f3e SR	93	/*-----------------------------------------------------------------------
	94	* FLASH related
	95	----------------------------------------------------------------------/
c440bfe6	96	#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
6d0f6bcf	97	#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
00b1883a	98	#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
3cb86f3e	99
6d0f6bcf JCPV	100	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
	101	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	102	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
3cb86f3e	103
6d0f6bcf JCPV	104	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
6d0f6bcf JCPV	105	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
3cb86f3e	106
6d0f6bcf JCPV	107	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
6d0f6bcf JCPV	108	#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
3cb86f3e	109
c440bfe6	110	#else
8a805df1 SR	111	/*
	112	* No NOR-flash on Acadia when NAND-booting. We need to undef the
	113	* NOR device-tree fixup code as well, since flash_info is not defined
	114	* in this case.
	115	*/
	116	#define CONFIG_SYS_NO_FLASH 1
	117	#undef CONFIG_FDT_FIXUP_NOR_FLASH_SIZE
c440bfe6 SR	118	#endif
c440bfe6 SR	119
5a1aceb0	120	#ifdef CONFIG_ENV_IS_IN_FLASH
0e8d1586	121	#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
6d0f6bcf	122	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
0e8d1586	123	#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
3cb86f3e SR	124
3cb86f3e SR	125	/* Address and size of Redundant Environment Sector */
0e8d1586 JCPV	126	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
0e8d1586 JCPV	127	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
3cb86f3e SR	128	#endif
3cb86f3e SR	129
c440bfe6 SR	130	/*
	131	* IPL (Initial Program Loader, integrated inside CPU)
	132	* Will load first 4k from NAND (SPL) into cache and execute it from there.
	133	*
	134	* SPL (Secondary Program Loader)
	135	* Will load special U-Boot version (NUB) from NAND and execute it. This SPL
	136	* has to fit into 4kByte. It sets up the CPU and configures the SDRAM
	137	* controller and the NAND controller so that the special U-Boot image can be
	138	* loaded from NAND to SDRAM.
	139	*
	140	* NUB (NAND U-Boot)
	141	* This NAND U-Boot (NUB) is a special U-Boot version which can be started
	142	* from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
	143	*
	144	* On 440EPx the SPL is copied to SDRAM before the NAND controller is
	145	* set up. While still running from cache, I experienced problems accessing
	146	* the NAND controller. sr - 2006-08-25
	147	*/
6d0f6bcf JCPV	148	#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
	149	#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
	150	#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_DATA_ADDR + (16 << 10)) /* Copy SPL here*/
	151	#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
	152	#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */
	153	#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
c440bfe6 SR	154
	155	/*
	156	* Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
	157	*/
6d0f6bcf JCPV	158	#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
6d0f6bcf JCPV	159	#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
c440bfe6 SR	160
	161	/*
	162	* Now the NAND chip has to be defined (no autodetection used!)
	163	*/
6d0f6bcf JCPV	164	#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */
	165	#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
	166	#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */
	167	#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
	168	#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
	169
	170	#define CONFIG_SYS_NAND_ECCSIZE 256
	171	#define CONFIG_SYS_NAND_ECCBYTES 3
6d0f6bcf	172	#define CONFIG_SYS_NAND_OOBSIZE 16
6d0f6bcf	173	#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
c440bfe6	174
51bfee19	175	#ifdef CONFIG_ENV_IS_IN_NAND
c440bfe6 SR	176	/*
	177	* For NAND booting the environment is embedded in the U-Boot image. Please take
	178	* look at the file board/amcc/sequoia/u-boot-nand.lds for details.
	179	*/
6d0f6bcf JCPV	180	#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
6d0f6bcf JCPV	181	#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
0e8d1586	182	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
c440bfe6 SR	183	#endif
c440bfe6 SR	184
3cb86f3e SR	185	/*-----------------------------------------------------------------------
	186	* RAM (CRAM)
	187	----------------------------------------------------------------------/
6d0f6bcf	188	#define CONFIG_SYS_MBYTES_RAM 64 /* 64MB */
3cb86f3e SR	189
	190	/*-----------------------------------------------------------------------
	191	* I2C
	192	----------------------------------------------------------------------/
880540de	193	#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
3cb86f3e	194
6d0f6bcf JCPV	195	#define CONFIG_SYS_I2C_MULTI_EEPROMS
	196	#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
	197	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	198	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	199	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
3cb86f3e SR	200
	201	/* I2C SYSMON (LM75, AD7414 is almost compatible) */
	202	#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
	203	#define CONFIG_DTT_AD7414 1 /* use AD7414 */
	204	#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
6d0f6bcf JCPV	205	#define CONFIG_SYS_DTT_MAX_TEMP 70
	206	#define CONFIG_SYS_DTT_LOW_TEMP -30
	207	#define CONFIG_SYS_DTT_HYSTERESIS 3
3cb86f3e	208
3cb86f3e SR	209	/*-----------------------------------------------------------------------
	210	* Ethernet
	211	----------------------------------------------------------------------/
3cb86f3e	212	#define CONFIG_PHY_ADDR 0 /* PHY address */
d1c1ba85	213	#define CONFIG_HAS_ETH0 1
3cb86f3e	214
490f2040 SR	215	/*
	216	* Default environment variables
	217	*/
16c0cc1c	218	#define CONFIG_EXTRA_ENV_SETTINGS \
490f2040	219	CONFIG_AMCC_DEF_ENV \
84a45d33 SR	220	CONFIG_AMCC_DEF_ENV_POWERPC \
84a45d33 SR	221	CONFIG_AMCC_DEF_ENV_PPC_OLD \
490f2040 SR	222	CONFIG_AMCC_DEF_ENV_NOR_UPD \
490f2040 SR	223	CONFIG_AMCC_DEF_ENV_NAND_UPD \
16c0cc1c SR	224	"kernel_addr=fff10000\0" \
16c0cc1c SR	225	"ramdisk_addr=fff20000\0" \
16c0cc1c SR	226	"kozio=bootm ffc60000\0" \
16c0cc1c SR	227	""
16c0cc1c	228
16c0cc1c SR	229	#define CONFIG_USB_OHCI
	230	#define CONFIG_USB_STORAGE
	231
16c0cc1c SR	232	/* Partitions */
	233	#define CONFIG_MAC_PARTITION
	234	#define CONFIG_DOS_PARTITION
	235	#define CONFIG_ISO_PARTITION
	236
	237	#define CONFIG_SUPPORT_VFAT
	238
079a136c	239	/*
490f2040	240	* Commands additional to the ones defined in amcc-common.h
079a136c	241	*/
0b361c91	242	#define CONFIG_CMD_DTT
0b361c91	243	#define CONFIG_CMD_NAND
0b361c91 JL	244	#define CONFIG_CMD_USB
	245
	246	/*
	247	* No NOR on Acadia when NAND-booting
	248	*/
	249	#if defined(CONFIG_NAND_U_BOOT) \|\| defined(CONFIG_NAND_SPL)
	250	#undef CONFIG_CMD_FLASH
	251	#undef CONFIG_CMD_IMLS
	252	#endif
	253
16c0cc1c SR	254	/*-----------------------------------------------------------------------
	255	* NAND FLASH
	256	----------------------------------------------------------------------/
6d0f6bcf	257	#define CONFIG_SYS_MAX_NAND_DEVICE 1
6d0f6bcf JCPV	258	#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
6d0f6bcf JCPV	259	#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
16c0cc1c	260
16c0cc1c SR	261	/*-----------------------------------------------------------------------
16c0cc1c SR	262	* External Bus Controller (EBC) Setup
3cb86f3e	263	----------------------------------------------------------------------/
c440bfe6	264	#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
6d0f6bcf	265	#define CONFIG_SYS_NAND_CS 3
3cb86f3e	266	/* Memory Bank 0 (Flash) initialization */
6d0f6bcf JCPV	267	#define CONFIG_SYS_EBC_PB0AP 0x03337200
6d0f6bcf JCPV	268	#define CONFIG_SYS_EBC_PB0CR 0xfe0bc000
16c0cc1c	269
c440bfe6	270	/* Memory Bank 3 (NAND-FLASH) initialization */
6d0f6bcf JCPV	271	#define CONFIG_SYS_EBC_PB3AP 0x018003c0
6d0f6bcf JCPV	272	#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR \| 0x1c000)
c440bfe6	273
3cb86f3e SR	274	/* Just initial configuration for CRAM. Will be changed in memory.c to sync mode*/
3cb86f3e SR	275	/* Memory Bank 1 (CRAM) initialization */
6d0f6bcf JCPV	276	#define CONFIG_SYS_EBC_PB1AP 0x030400c0
6d0f6bcf JCPV	277	#define CONFIG_SYS_EBC_PB1CR 0x000bc000
16c0cc1c	278
3cb86f3e	279	/* Memory Bank 2 (CRAM) initialization */
6d0f6bcf JCPV	280	#define CONFIG_SYS_EBC_PB2AP 0x030400c0
6d0f6bcf JCPV	281	#define CONFIG_SYS_EBC_PB2CR 0x020bc000
c440bfe6	282	#else
6d0f6bcf	283	#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */
c440bfe6	284	/* Memory Bank 0 (NAND-FLASH) initialization */
6d0f6bcf JCPV	285	#define CONFIG_SYS_EBC_PB0AP 0x018003c0
6d0f6bcf JCPV	286	#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR \| 0x1c000)
16c0cc1c	287
c440bfe6 SR	288	/*
	289	* When NAND-booting the CRAM EBC setup must be done in sync mode, since the
	290	* NAND-SPL already initialized the CRAM and EBC to sync mode.
	291	*/
	292	/* Memory Bank 1 (CRAM) initialization */
6d0f6bcf JCPV	293	#define CONFIG_SYS_EBC_PB1AP 0x9C0201C0
6d0f6bcf JCPV	294	#define CONFIG_SYS_EBC_PB1CR 0x000bc000
c440bfe6 SR	295
c440bfe6 SR	296	/* Memory Bank 2 (CRAM) initialization */
6d0f6bcf JCPV	297	#define CONFIG_SYS_EBC_PB2AP 0x9C0201C0
6d0f6bcf JCPV	298	#define CONFIG_SYS_EBC_PB2CR 0x020bc000
c440bfe6	299	#endif
16c0cc1c	300
3cb86f3e	301	/* Memory Bank 4 (CPLD) initialization */
6d0f6bcf JCPV	302	#define CONFIG_SYS_EBC_PB4AP 0x04006000
6d0f6bcf JCPV	303	#define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_CPLD_BASE \| 0x18000)
16c0cc1c	304
6d0f6bcf	305	#define CONFIG_SYS_EBC_CFG 0xf8400000
16c0cc1c	306
3cb86f3e SR	307	/*-----------------------------------------------------------------------
	308	* GPIO Setup
	309	----------------------------------------------------------------------/
6d0f6bcf JCPV	310	#define CONFIG_SYS_GPIO_CRAM_CLK 8
	311	#define CONFIG_SYS_GPIO_CRAM_WAIT 9 /* GPIO-In */
	312	#define CONFIG_SYS_GPIO_CRAM_ADV 10
	313	#define CONFIG_SYS_GPIO_CRAM_CRE (32 + 21) /* GPIO-Out */
3cb86f3e	314
16c0cc1c SR	315	/*-----------------------------------------------------------------------
	316	* Definitions for GPIO_0 setup (PPC405EZ specific)
	317	*
5d4a1790 SR	318	* GPIO0[0-2] - External Bus Controller CS_4 - CS_6 Outputs
5d4a1790 SR	319	* GPIO0[3] - NAND FLASH Controller CE3 (NFCE3) Output
16c0cc1c SR	320	* GPIO0[4] - External Bus Controller Hold Input
	321	* GPIO0[5] - External Bus Controller Priority Input
	322	* GPIO0[6] - External Bus Controller HLDA Output
	323	* GPIO0[7] - External Bus Controller Bus Request Output
	324	* GPIO0[8] - CRAM Clk Output
	325	* GPIO0[9] - External Bus Controller Ready Input
	326	* GPIO0[10] - CRAM Adv Output
	327	* GPIO0[11-24] - NAND Flash Control Data -> Bypasses GPIO when enabled
	328	* GPIO0[25] - External DMA Request Input
	329	* GPIO0[26] - External DMA EOT I/O
	330	* GPIO0[25] - External DMA Ack_n Output
	331	* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
	332	* GPIO0[28-30] - Trace Outputs / PWM Inputs
	333	* GPIO0[31] - PWM_8 I/O
	334	*/
6d0f6bcf JCPV	335	#define CONFIG_SYS_GPIO0_TCR 0xC0A00000
	336	#define CONFIG_SYS_GPIO0_OSRL 0x50004400
	337	#define CONFIG_SYS_GPIO0_OSRH 0x02000055
	338	#define CONFIG_SYS_GPIO0_ISR1L 0x00001000
	339	#define CONFIG_SYS_GPIO0_ISR1H 0x00000055
	340	#define CONFIG_SYS_GPIO0_TSRL 0x02000000
	341	#define CONFIG_SYS_GPIO0_TSRH 0x00000055
16c0cc1c SR	342
	343	/*-----------------------------------------------------------------------
	344	* Definitions for GPIO_1 setup (PPC405EZ specific)
	345	*
	346	* GPIO1[0-6] - PWM_9 to PWM_15 I/O
	347	* GPIO1[7] - PWM_DIV_CLK (Out) / IRQ4 Input
	348	* GPIO1[8] - TS5 Output / DAC_IP_TRIG Input
	349	* GPIO1[9] - TS6 Output / ADC_IP_TRIG Input
	350	* GPIO1[10-12] - UART0 Control Inputs
	351	* GPIO1[13] - UART0_DTR_N Output/IEEE_1588_TS Output/TMRCLK Input
	352	* GPIO1[14] - UART0_RTS_N Output/SPI_SS_2_N Output
	353	* GPIO1[15] - SPI_SS_3_N Output/UART0_RI_N Input
	354	* GPIO1[16] - SPI_SS_1_N Output
	355	* GPIO1[17-20] - Trace Output/External Interrupts IRQ0 - IRQ3 inputs
	356	*/
6d0f6bcf JCPV	357	#define CONFIG_SYS_GPIO1_TCR 0xFFFF8414
	358	#define CONFIG_SYS_GPIO1_OSRL 0x40000110
	359	#define CONFIG_SYS_GPIO1_OSRH 0x55455555
	360	#define CONFIG_SYS_GPIO1_ISR1L 0x15555445
	361	#define CONFIG_SYS_GPIO1_ISR1H 0x00000000
	362	#define CONFIG_SYS_GPIO1_TSRL 0x00000000
	363	#define CONFIG_SYS_GPIO1_TSRH 0x00000000
16c0cc1c	364
16c0cc1c	365	#endif /* __CONFIG_H */