[J-u-boot.git] / env / Kconfig

menu "Environment"

config ENV_IS_NOWHERE
	bool "Environment is not stored"
	depends on !ENV_IS_IN_EEPROM
	depends on !ENV_IS_IN_FAT
	depends on !ENV_IS_IN_FLASH
	depends on !ENV_IS_IN_MMC
	depends on !ENV_IS_IN_NAND
	depends on !ENV_IS_IN_NVRAM
	depends on !ENV_IS_IN_ONENAND
	depends on !ENV_IS_IN_REMOTE
	depends on !ENV_IS_IN_SPI_FLASH
	depends on !ENV_IS_IN_UBI
	default y
	help
	  Define this if you don't want to or can't have an environment stored
	  on a storage medium. In this case the environemnt will still exist
	  while U-Boot is running, but once U-Boot exits it will not be
	  stored. U-Boot will therefore always start up with a default
	  environment.

config ENV_IS_IN_EEPROM
	bool "Environment in EEPROM"
	depends on !CHAIN_OF_TRUST
	help
	  Use this if you have an EEPROM or similar serial access
	  device and a driver for it.

	  - CONFIG_ENV_OFFSET:
	  - CONFIG_ENV_SIZE:

	  These two #defines specify the offset and size of the
	  environment area within the total memory of your EEPROM.

	  Note that we consider the length of the address field to
	  still be one byte because the extra address bits are hidden
	  in the chip address.

	  - CONFIG_ENV_EEPROM_IS_ON_I2C
	  define this, if you have I2C and SPI activated, and your
	  EEPROM, which holds the environment, is on the I2C bus.

	  - CONFIG_I2C_ENV_EEPROM_BUS
	  if you have an Environment on an EEPROM reached over
	  I2C muxes, you can define here, how to reach this
	  EEPROM. For example:

	  #define CONFIG_I2C_ENV_EEPROM_BUS	  1

	  EEPROM which holds the environment, is reached over
	  a pca9547 i2c mux with address 0x70, channel 3.

config ENV_IS_IN_FAT
	bool "Environment is in a FAT filesystem"
	depends on !CHAIN_OF_TRUST
	default y if ARCH_BCM283X
	default y if ARCH_SUNXI && MMC
	default y if MMC_OMAP_HS && TI_COMMON_CMD_OPTIONS
	select FS_FAT
	select FAT_WRITE
	help
	  Define this if you want to use the FAT file system for the environment.

config ENV_IS_IN_EXT4
	bool "Environment is in a EXT4 filesystem"
	depends on !CHAIN_OF_TRUST
	select EXT4_WRITE
	help
	  Define this if you want to use the EXT4 file system for the environment.

config ENV_IS_IN_FLASH
	bool "Environment in flash memory"
	depends on !CHAIN_OF_TRUST
	default y if ARCH_CINTEGRATOR
	default y if ARCH_INTEGRATOR_CP
	default y if M548x || M547x || M5282 || MCF547x_8x
	default y if MCF532x || MCF52x2
	default y if MPC86xx || MPC83xx
	default y if ARCH_MPC8572 || ARCH_MPC8548 || ARCH_MPC8641
	default y if SH && !CPU_SH4
	help
	  Define this if you have a flash device which you want to use for the
	  environment.

	  a) The environment occupies one whole flash sector, which is
	   "embedded" in the text segment with the U-Boot code. This
	   happens usually with "bottom boot sector" or "top boot
	   sector" type flash chips, which have several smaller
	   sectors at the start or the end. For instance, such a
	   layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
	   such a case you would place the environment in one of the
	   4 kB sectors - with U-Boot code before and after it. With
	   "top boot sector" type flash chips, you would put the
	   environment in one of the last sectors, leaving a gap
	   between U-Boot and the environment.

	  CONFIG_ENV_OFFSET:

	   Offset of environment data (variable area) to the
	   beginning of flash memory; for instance, with bottom boot
	   type flash chips the second sector can be used: the offset
	   for this sector is given here.

	   CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.

	  CONFIG_ENV_ADDR:

	   This is just another way to specify the start address of
	   the flash sector containing the environment (instead of
	   CONFIG_ENV_OFFSET).

	  CONFIG_ENV_SECT_SIZE:

	   Size of the sector containing the environment.


	  b) Sometimes flash chips have few, equal sized, BIG sectors.
	   In such a case you don't want to spend a whole sector for
	   the environment.

	  CONFIG_ENV_SIZE:

	   If you use this in combination with CONFIG_ENV_IS_IN_FLASH
	   and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
	   of this flash sector for the environment. This saves
	   memory for the RAM copy of the environment.

	   It may also save flash memory if you decide to use this
	   when your environment is "embedded" within U-Boot code,
	   since then the remainder of the flash sector could be used
	   for U-Boot code. It should be pointed out that this is
	   STRONGLY DISCOURAGED from a robustness point of view:
	   updating the environment in flash makes it always
	   necessary to erase the WHOLE sector. If something goes
	   wrong before the contents has been restored from a copy in
	   RAM, your target system will be dead.

	  CONFIG_ENV_ADDR_REDUND
	  CONFIG_ENV_SIZE_REDUND

	   These settings describe a second storage area used to hold
	   a redundant copy of the environment data, so that there is
	   a valid backup copy in case there is a power failure during
	   a "saveenv" operation.

	  BE CAREFUL! Any changes to the flash layout, and some changes to the
	  source code will make it necessary to adapt <board>/u-boot.lds*
	  accordingly!

config ENV_IS_IN_MMC
	bool "Environment in an MMC device"
	depends on !CHAIN_OF_TRUST
	depends on MMC
	default y if ARCH_EXYNOS4
	default y if MX6SX || MX7D
	default y if TEGRA30 || TEGRA124
	default y if TEGRA_ARMV8_COMMON
	help
	  Define this if you have an MMC device which you want to use for the
	  environment.

	  CONFIG_SYS_MMC_ENV_DEV:

	  Specifies which MMC device the environment is stored in.

	  CONFIG_SYS_MMC_ENV_PART (optional):

	  Specifies which MMC partition the environment is stored in. If not
	  set, defaults to partition 0, the user area. Common values might be
	  1 (first MMC boot partition), 2 (second MMC boot partition).

	  CONFIG_ENV_OFFSET:
	  CONFIG_ENV_SIZE:

	  These two #defines specify the offset and size of the environment
	  area within the specified MMC device.

	  If offset is positive (the usual case), it is treated as relative to
	  the start of the MMC partition. If offset is negative, it is treated
	  as relative to the end of the MMC partition. This can be useful if
	  your board may be fitted with different MMC devices, which have
	  different sizes for the MMC partitions, and you always want the
	  environment placed at the very end of the partition, to leave the
	  maximum possible space before it, to store other data.

	  These two values are in units of bytes, but must be aligned to an
	  MMC sector boundary.

	  CONFIG_ENV_OFFSET_REDUND (optional):

	  Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
	  hold a redundant copy of the environment data. This provides a
	  valid backup copy in case the other copy is corrupted, e.g. due
	  to a power failure during a "saveenv" operation.

	  This value may also be positive or negative; this is handled in the
	  same way as CONFIG_ENV_OFFSET.

	  This value is also in units of bytes, but must also be aligned to
	  an MMC sector boundary.

	  CONFIG_ENV_SIZE_REDUND (optional):

	  This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
	  set. If this value is set, it must be set to the same value as
	  CONFIG_ENV_SIZE.

config ENV_IS_IN_NAND
	bool "Environment in a NAND device"
	depends on !CHAIN_OF_TRUST
	help
	  Define this if you have a NAND device which you want to use for the
	  environment.

	  - CONFIG_ENV_OFFSET:
	  - CONFIG_ENV_SIZE:

	  These two #defines specify the offset and size of the environment
	  area within the first NAND device.  CONFIG_ENV_OFFSET must be
	  aligned to an erase block boundary.

	  - CONFIG_ENV_OFFSET_REDUND (optional):

	  This setting describes a second storage area of CONFIG_ENV_SIZE
	  size used to hold a redundant copy of the environment data, so
	  that there is a valid backup copy in case there is a power failure
	  during a "saveenv" operation.	 CONFIG_ENV_OFFSET_REDUND must be
	  aligned to an erase block boundary.

	  - CONFIG_ENV_RANGE (optional):

	  Specifies the length of the region in which the environment
	  can be written.  This should be a multiple of the NAND device's
	  block size.  Specifying a range with more erase blocks than
	  are needed to hold CONFIG_ENV_SIZE allows bad blocks within
	  the range to be avoided.

	  - CONFIG_ENV_OFFSET_OOB (optional):

	  Enables support for dynamically retrieving the offset of the
	  environment from block zero's out-of-band data.  The
	  "nand env.oob" command can be used to record this offset.
	  Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
	  using CONFIG_ENV_OFFSET_OOB.

config ENV_IS_IN_NVRAM
	bool "Environment in a non-volatile RAM"
	depends on !CHAIN_OF_TRUST
	help
	  Define this if you have some non-volatile memory device
	  (NVRAM, battery buffered SRAM) which you want to use for the
	  environment.

	  - CONFIG_ENV_ADDR:
	  - CONFIG_ENV_SIZE:

	  These two #defines are used to determine the memory area you
	  want to use for environment. It is assumed that this memory
	  can just be read and written to, without any special
	  provision.

config ENV_IS_IN_ONENAND
	bool "Environment is in OneNAND"
	depends on !CHAIN_OF_TRUST
	help
	  Define this if you want to put your local device's environment in
	  OneNAND.

	  - CONFIG_ENV_ADDR:
	  - CONFIG_ENV_SIZE:

	  These two #defines are used to determine the device range you
	  want to use for environment. It is assumed that this memory
	  can just be read and written to, without any special
	  provision.

config ENV_IS_IN_REMOTE
	bool "Environment is in remove memory space"
	depends on !CHAIN_OF_TRUST
	help
	  Define this if you have a remote memory space which you
	  want to use for the local device's environment.

	  - CONFIG_ENV_ADDR:
	  - CONFIG_ENV_SIZE:

	  These two #defines specify the address and size of the
	  environment area within the remote memory space. The
	  local device can get the environment from remote memory
	  space by SRIO or PCIE links.

config ENV_IS_IN_SPI_FLASH
	bool "Environment is in SPI flash"
	depends on !CHAIN_OF_TRUST
	default y if ARMADA_XP
	default y if INTEL_BAYTRAIL
	default y if INTEL_BRASWELL
	default y if INTEL_BROADWELL
	default y if NORTHBRIDGE_INTEL_IVYBRIDGE
	default y if INTEL_QUARK
	default y if INTEL_QUEENSBAY
	help
	  Define this if you have a SPI Flash memory device which you
	  want to use for the environment.

	  - CONFIG_ENV_OFFSET:
	  - CONFIG_ENV_SIZE:

	  These two #defines specify the offset and size of the
	  environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
	  aligned to an erase sector boundary.

	  - CONFIG_ENV_SECT_SIZE:

	  Define the SPI flash's sector size.

	  - CONFIG_ENV_OFFSET_REDUND (optional):

	  This setting describes a second storage area of CONFIG_ENV_SIZE
	  size used to hold a redundant copy of the environment data, so
	  that there is a valid backup copy in case there is a power failure
	  during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
	  aligned to an erase sector boundary.

	  - CONFIG_ENV_SPI_BUS (optional):
	  - CONFIG_ENV_SPI_CS (optional):

	  Define the SPI bus and chip select. If not defined they will be 0.

	  - CONFIG_ENV_SPI_MAX_HZ (optional):

	  Define the SPI max work clock. If not defined then use 1MHz.

	  - CONFIG_ENV_SPI_MODE (optional):

	  Define the SPI work mode. If not defined then use SPI_MODE_3.

config ENV_IS_IN_UBI
	bool "Environment in a UBI volume"
	depends on !CHAIN_OF_TRUST
	help
	  Define this if you have an UBI volume that you want to use for the
	  environment.  This has the benefit of wear-leveling the environment
	  accesses, which is important on NAND.

	  - CONFIG_ENV_UBI_PART:

	  Define this to a string that is the mtd partition containing the UBI.

	  - CONFIG_ENV_UBI_VOLUME:

	  Define this to the name of the volume that you want to store the
	  environment in.

	  - CONFIG_ENV_UBI_VOLUME_REDUND:

	  Define this to the name of another volume to store a second copy of
	  the environment in.  This will enable redundant environments in UBI.
	  It is assumed that both volumes are in the same MTD partition.

config ENV_FAT_INTERFACE
	string "Name of the block device for the environment"
	depends on ENV_IS_IN_FAT
	default "mmc" if ARCH_SUNXI
	default "mmc" if TI_COMMON_CMD_OPTIONS || ARCH_ZYNQMP || ARCH_AT91
	help
	  Define this to a string that is the name of the block device.

config ENV_FAT_DEVICE_AND_PART
	string "Device and partition for where to store the environemt in FAT"
	depends on ENV_IS_IN_FAT
	default "0:1" if TI_COMMON_CMD_OPTIONS
	default "0:auto" if ARCH_ZYNQMP
	default "0:auto" if ARCH_SUNXI && MMC_SUNXI_SLOT_EXTRA = -1
	default "1:auto" if ARCH_SUNXI && MMC_SUNXI_SLOT_EXTRA != -1
	default "0" if ARCH_AT91
	help
	  Define this to a string to specify the partition of the device. It can
	  be as following:

	    "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
	       - "D:P": device D partition P. Error occurs if device D has no
	                partition table.
	       - "D:0": device D.
	       - "D" or "D:": device D partition 1 if device D has partition
	                      table, or the whole device D if has no partition
	                      table.
	       - "D:auto": first partition in device D with bootable flag set.
	                   If none, first valid partition in device D. If no
	                   partition table then means device D.

config ENV_FAT_FILE
	string "Name of the FAT file to use for the environemnt"
	depends on ENV_IS_IN_FAT
	default "uboot.env"
	help
	  It's a string of the FAT file name. This file use to store the
	  environment.

config ENV_EXT4_INTERFACE
	string "Name of the block device for the environment"
	depends on ENV_IS_IN_EXT4
	help
	  Define this to a string that is the name of the block device.

config ENV_EXT4_DEVICE_AND_PART
	string "Device and partition for where to store the environemt in EXT4"
	depends on ENV_IS_IN_EXT4
	help
	  Define this to a string to specify the partition of the device. It can
	  be as following:

	    "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
	       - "D:P": device D partition P. Error occurs if device D has no
	                partition table.
	       - "D:0": device D.
	       - "D" or "D:": device D partition 1 if device D has partition
	                      table, or the whole device D if has no partition
	                      table.
	       - "D:auto": first partition in device D with bootable flag set.
	                   If none, first valid partition in device D. If no
	                   partition table then means device D.

config ENV_EXT4_FILE
	string "Name of the EXT4 file to use for the environemnt"
	depends on ENV_IS_IN_EXT4
	default "uboot.env"
	help
	  It's a string of the EXT4 file name. This file use to store the
	  environment (explicit path to the file)

if ARCH_SUNXI

config ENV_OFFSET
	hex "Environment Offset"
	depends on !ENV_IS_IN_UBI
	depends on !ENV_IS_NOWHERE
	default 0x88000 if ARCH_SUNXI
	help
	  Offset from the start of the device (or partition)

config ENV_SIZE
	hex "Environment Size"
	depends on !ENV_IS_NOWHERE
	default 0x20000 if ARCH_SUNXI
	help
	  Size of the environment storage area

config ENV_UBI_PART
	string "UBI partition name"
	depends on ENV_IS_IN_UBI
	help
	  MTD partition containing the UBI device

config ENV_UBI_VOLUME
	string "UBI volume name"
	depends on ENV_IS_IN_UBI
	help
	  Name of the volume that you want to store the environment in.

endif

if ARCH_ROCKCHIP

config ENV_OFFSET
	hex
	depends on !ENV_IS_IN_UBI
	depends on !ENV_IS_NOWHERE
	default 0x3f8000
	help
	  Offset from the start of the device (or partition)

config ENV_SIZE
	hex
	default 0x8000
	help
	  Size of the environment storage area

endif

endmenu
Commit	Line	Data
0649cd0d SG	1	menu "Environment"
0649cd0d SG	2
c1c3fe23 SG	3	config ENV_IS_NOWHERE
c1c3fe23 SG	4	bool "Environment is not stored"
fb69464e MR	5	depends on !ENV_IS_IN_EEPROM
	6	depends on !ENV_IS_IN_FAT
	7	depends on !ENV_IS_IN_FLASH
	8	depends on !ENV_IS_IN_MMC
	9	depends on !ENV_IS_IN_NAND
	10	depends on !ENV_IS_IN_NVRAM
	11	depends on !ENV_IS_IN_ONENAND
	12	depends on !ENV_IS_IN_REMOTE
	13	depends on !ENV_IS_IN_SPI_FLASH
	14	depends on !ENV_IS_IN_UBI
	15	default y
c1c3fe23 SG	16	help
	17	Define this if you don't want to or can't have an environment stored
	18	on a storage medium. In this case the environemnt will still exist
	19	while U-Boot is running, but once U-Boot exits it will not be
	20	stored. U-Boot will therefore always start up with a default
	21	environment.
	22
0649cd0d SG	23	config ENV_IS_IN_EEPROM
	24	bool "Environment in EEPROM"
	25	depends on !CHAIN_OF_TRUST
	26	help
	27	Use this if you have an EEPROM or similar serial access
	28	device and a driver for it.
	29
	30	- CONFIG_ENV_OFFSET:
	31	- CONFIG_ENV_SIZE:
	32
	33	These two #defines specify the offset and size of the
	34	environment area within the total memory of your EEPROM.
	35
0649cd0d SG	36	Note that we consider the length of the address field to
	37	still be one byte because the extra address bits are hidden
	38	in the chip address.
	39
0649cd0d SG	40	- CONFIG_ENV_EEPROM_IS_ON_I2C
	41	define this, if you have I2C and SPI activated, and your
	42	EEPROM, which holds the environment, is on the I2C bus.
	43
	44	- CONFIG_I2C_ENV_EEPROM_BUS
	45	if you have an Environment on an EEPROM reached over
	46	I2C muxes, you can define here, how to reach this
	47	EEPROM. For example:
	48
	49	#define CONFIG_I2C_ENV_EEPROM_BUS 1
	50
	51	EEPROM which holds the environment, is reached over
	52	a pca9547 i2c mux with address 0x70, channel 3.
	53
	54	config ENV_IS_IN_FAT
	55	bool "Environment is in a FAT filesystem"
	56	depends on !CHAIN_OF_TRUST
fb69464e	57	default y if ARCH_BCM283X
0163c918	58	default y if ARCH_SUNXI && MMC
fb69464e	59	default y if MMC_OMAP_HS && TI_COMMON_CMD_OPTIONS
3cd084d3	60	select FS_FAT
0649cd0d SG	61	select FAT_WRITE
0649cd0d SG	62	help
91d3aa05	63	Define this if you want to use the FAT file system for the environment.
0649cd0d	64
1087a794 JRO	65	config ENV_IS_IN_EXT4
	66	bool "Environment is in a EXT4 filesystem"
	67	depends on !CHAIN_OF_TRUST
	68	select EXT4_WRITE
	69	help
	70	Define this if you want to use the EXT4 file system for the environment.
	71
0649cd0d SG	72	config ENV_IS_IN_FLASH
	73	bool "Environment in flash memory"
	74	depends on !CHAIN_OF_TRUST
fb69464e MR	75	default y if ARCH_CINTEGRATOR
	76	default y if ARCH_INTEGRATOR_CP
	77	default y if M548x \|\| M547x \|\| M5282 \|\| MCF547x_8x
	78	default y if MCF532x \|\| MCF52x2
	79	default y if MPC86xx \|\| MPC83xx
	80	default y if ARCH_MPC8572 \|\| ARCH_MPC8548 \|\| ARCH_MPC8641
	81	default y if SH && !CPU_SH4
0649cd0d SG	82	help
	83	Define this if you have a flash device which you want to use for the
	84	environment.
	85
	86	a) The environment occupies one whole flash sector, which is
	87	"embedded" in the text segment with the U-Boot code. This
	88	happens usually with "bottom boot sector" or "top boot
	89	sector" type flash chips, which have several smaller
	90	sectors at the start or the end. For instance, such a
	91	layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
	92	such a case you would place the environment in one of the
	93	4 kB sectors - with U-Boot code before and after it. With
	94	"top boot sector" type flash chips, you would put the
	95	environment in one of the last sectors, leaving a gap
	96	between U-Boot and the environment.
	97
	98	CONFIG_ENV_OFFSET:
	99
	100	Offset of environment data (variable area) to the
	101	beginning of flash memory; for instance, with bottom boot
	102	type flash chips the second sector can be used: the offset
	103	for this sector is given here.
	104
	105	CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
	106
	107	CONFIG_ENV_ADDR:
	108
	109	This is just another way to specify the start address of
	110	the flash sector containing the environment (instead of
	111	CONFIG_ENV_OFFSET).
	112
	113	CONFIG_ENV_SECT_SIZE:
	114
	115	Size of the sector containing the environment.
	116
	117
	118	b) Sometimes flash chips have few, equal sized, BIG sectors.
	119	In such a case you don't want to spend a whole sector for
	120	the environment.
	121
	122	CONFIG_ENV_SIZE:
	123
	124	If you use this in combination with CONFIG_ENV_IS_IN_FLASH
	125	and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
	126	of this flash sector for the environment. This saves
	127	memory for the RAM copy of the environment.
	128
	129	It may also save flash memory if you decide to use this
	130	when your environment is "embedded" within U-Boot code,
	131	since then the remainder of the flash sector could be used
	132	for U-Boot code. It should be pointed out that this is
	133	STRONGLY DISCOURAGED from a robustness point of view:
	134	updating the environment in flash makes it always
	135	necessary to erase the WHOLE sector. If something goes
	136	wrong before the contents has been restored from a copy in
	137	RAM, your target system will be dead.
	138
	139	CONFIG_ENV_ADDR_REDUND
	140	CONFIG_ENV_SIZE_REDUND
	141
	142	These settings describe a second storage area used to hold
	143	a redundant copy of the environment data, so that there is
	144	a valid backup copy in case there is a power failure during
	145	a "saveenv" operation.
146
147	BE CAREFUL! Any changes to the flash layout, and some changes to the
148	source code will make it necessary to adapt <board>/u-boot.lds*
149	accordingly!
150
151	config ENV_IS_IN_MMC
152	bool "Environment in an MMC device"
153	depends on !CHAIN_OF_TRUST
d282a1db	154	depends on MMC
fb69464e MR	155	default y if ARCH_EXYNOS4
	156	default y if MX6SX \|\| MX7D
	157	default y if TEGRA30 \|\| TEGRA124
	158	default y if TEGRA_ARMV8_COMMON
0649cd0d SG	159	help
	160	Define this if you have an MMC device which you want to use for the
	161	environment.
	162
	163	CONFIG_SYS_MMC_ENV_DEV:
	164
	165	Specifies which MMC device the environment is stored in.
	166
	167	CONFIG_SYS_MMC_ENV_PART (optional):
	168
	169	Specifies which MMC partition the environment is stored in. If not
	170	set, defaults to partition 0, the user area. Common values might be
	171	1 (first MMC boot partition), 2 (second MMC boot partition).
	172
	173	CONFIG_ENV_OFFSET:
	174	CONFIG_ENV_SIZE:
	175
	176	These two #defines specify the offset and size of the environment
	177	area within the specified MMC device.
	178
	179	If offset is positive (the usual case), it is treated as relative to
	180	the start of the MMC partition. If offset is negative, it is treated
	181	as relative to the end of the MMC partition. This can be useful if
	182	your board may be fitted with different MMC devices, which have
	183	different sizes for the MMC partitions, and you always want the
	184	environment placed at the very end of the partition, to leave the
	185	maximum possible space before it, to store other data.
	186
	187	These two values are in units of bytes, but must be aligned to an
	188	MMC sector boundary.
	189
	190	CONFIG_ENV_OFFSET_REDUND (optional):
	191
	192	Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
	193	hold a redundant copy of the environment data. This provides a
	194	valid backup copy in case the other copy is corrupted, e.g. due
	195	to a power failure during a "saveenv" operation.
	196
	197	This value may also be positive or negative; this is handled in the
	198	same way as CONFIG_ENV_OFFSET.
	199
	200	This value is also in units of bytes, but must also be aligned to
	201	an MMC sector boundary.
	202
	203	CONFIG_ENV_SIZE_REDUND (optional):
	204
	205	This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
	206	set. If this value is set, it must be set to the same value as
	207	CONFIG_ENV_SIZE.
	208
	209	config ENV_IS_IN_NAND
	210	bool "Environment in a NAND device"
	211	depends on !CHAIN_OF_TRUST
	212	help
	213	Define this if you have a NAND device which you want to use for the
	214	environment.
	215
	216	- CONFIG_ENV_OFFSET:
	217	- CONFIG_ENV_SIZE:
	218
	219	These two #defines specify the offset and size of the environment
	220	area within the first NAND device. CONFIG_ENV_OFFSET must be
	221	aligned to an erase block boundary.
	222
223	- CONFIG_ENV_OFFSET_REDUND (optional):
224
225	This setting describes a second storage area of CONFIG_ENV_SIZE
226	size used to hold a redundant copy of the environment data, so
227	that there is a valid backup copy in case there is a power failure
228	during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
229	aligned to an erase block boundary.
230
231	- CONFIG_ENV_RANGE (optional):
232
233	Specifies the length of the region in which the environment
234	can be written. This should be a multiple of the NAND device's
235	block size. Specifying a range with more erase blocks than
236	are needed to hold CONFIG_ENV_SIZE allows bad blocks within
237	the range to be avoided.
238
239	- CONFIG_ENV_OFFSET_OOB (optional):
240
241	Enables support for dynamically retrieving the offset of the
242	environment from block zero's out-of-band data. The
243	"nand env.oob" command can be used to record this offset.
244	Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
245	using CONFIG_ENV_OFFSET_OOB.
246
247	config ENV_IS_IN_NVRAM
248	bool "Environment in a non-volatile RAM"
249	depends on !CHAIN_OF_TRUST
250	help
251	Define this if you have some non-volatile memory device
252	(NVRAM, battery buffered SRAM) which you want to use for the
253	environment.
254
255	- CONFIG_ENV_ADDR:
256	- CONFIG_ENV_SIZE:
257
258	These two #defines are used to determine the memory area you
259	want to use for environment. It is assumed that this memory
260	can just be read and written to, without any special
261	provision.
262
263	config ENV_IS_IN_ONENAND
264	bool "Environment is in OneNAND"
265	depends on !CHAIN_OF_TRUST
266	help
267	Define this if you want to put your local device's environment in
268	OneNAND.
269
270	- CONFIG_ENV_ADDR:
271	- CONFIG_ENV_SIZE:
272
273	These two #defines are used to determine the device range you
274	want to use for environment. It is assumed that this memory
275	can just be read and written to, without any special
276	provision.
277
278	config ENV_IS_IN_REMOTE
279	bool "Environment is in remove memory space"
280	depends on !CHAIN_OF_TRUST
281	help
282	Define this if you have a remote memory space which you
283	want to use for the local device's environment.
284
285	- CONFIG_ENV_ADDR:
286	- CONFIG_ENV_SIZE:
287
288	These two #defines specify the address and size of the
289	environment area within the remote memory space. The
290	local device can get the environment from remote memory
291	space by SRIO or PCIE links.
292
293	config ENV_IS_IN_SPI_FLASH
294	bool "Environment is in SPI flash"
295	depends on !CHAIN_OF_TRUST
fb69464e MR	296	default y if ARMADA_XP
	297	default y if INTEL_BAYTRAIL
	298	default y if INTEL_BRASWELL
	299	default y if INTEL_BROADWELL
	300	default y if NORTHBRIDGE_INTEL_IVYBRIDGE
	301	default y if INTEL_QUARK
	302	default y if INTEL_QUEENSBAY
0649cd0d SG	303	help
	304	Define this if you have a SPI Flash memory device which you
	305	want to use for the environment.
	306
	307	- CONFIG_ENV_OFFSET:
	308	- CONFIG_ENV_SIZE:
	309
	310	These two #defines specify the offset and size of the
	311	environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
	312	aligned to an erase sector boundary.
	313
	314	- CONFIG_ENV_SECT_SIZE:
	315
	316	Define the SPI flash's sector size.
	317
	318	- CONFIG_ENV_OFFSET_REDUND (optional):
	319
	320	This setting describes a second storage area of CONFIG_ENV_SIZE
	321	size used to hold a redundant copy of the environment data, so
	322	that there is a valid backup copy in case there is a power failure
	323	during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
	324	aligned to an erase sector boundary.
	325
	326	- CONFIG_ENV_SPI_BUS (optional):
	327	- CONFIG_ENV_SPI_CS (optional):
	328
	329	Define the SPI bus and chip select. If not defined they will be 0.
	330
	331	- CONFIG_ENV_SPI_MAX_HZ (optional):
	332
	333	Define the SPI max work clock. If not defined then use 1MHz.
	334
	335	- CONFIG_ENV_SPI_MODE (optional):
	336
	337	Define the SPI work mode. If not defined then use SPI_MODE_3.
	338
	339	config ENV_IS_IN_UBI
	340	bool "Environment in a UBI volume"
	341	depends on !CHAIN_OF_TRUST
	342	help
	343	Define this if you have an UBI volume that you want to use for the
	344	environment. This has the benefit of wear-leveling the environment
	345	accesses, which is important on NAND.
	346
	347	- CONFIG_ENV_UBI_PART:
	348
	349	Define this to a string that is the mtd partition containing the UBI.
	350
	351	- CONFIG_ENV_UBI_VOLUME:
	352
	353	Define this to the name of the volume that you want to store the
	354	environment in.
	355
	356	- CONFIG_ENV_UBI_VOLUME_REDUND:
	357
	358	Define this to the name of another volume to store a second copy of
	359	the environment in. This will enable redundant environments in UBI.
	360	It is assumed that both volumes are in the same MTD partition.
	361
0649cd0d SG	362	config ENV_FAT_INTERFACE
	363	string "Name of the block device for the environment"
	364	depends on ENV_IS_IN_FAT
0163c918	365	default "mmc" if ARCH_SUNXI
0649cd0d SG	366	default "mmc" if TI_COMMON_CMD_OPTIONS \|\| ARCH_ZYNQMP \|\| ARCH_AT91
	367	help
	368	Define this to a string that is the name of the block device.
	369
	370	config ENV_FAT_DEVICE_AND_PART
	371	string "Device and partition for where to store the environemt in FAT"
	372	depends on ENV_IS_IN_FAT
	373	default "0:1" if TI_COMMON_CMD_OPTIONS
	374	default "0:auto" if ARCH_ZYNQMP
0163c918 MR	375	default "0:auto" if ARCH_SUNXI && MMC_SUNXI_SLOT_EXTRA = -1
0163c918 MR	376	default "1:auto" if ARCH_SUNXI && MMC_SUNXI_SLOT_EXTRA != -1
0649cd0d SG	377	default "0" if ARCH_AT91
	378	help
	379	Define this to a string to specify the partition of the device. It can
	380	be as following:
	381
	382	"D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
	383	- "D:P": device D partition P. Error occurs if device D has no
	384	partition table.
	385	- "D:0": device D.
	386	- "D" or "D:": device D partition 1 if device D has partition
	387	table, or the whole device D if has no partition
	388	table.
	389	- "D:auto": first partition in device D with bootable flag set.
	390	If none, first valid partition in device D. If no
	391	partition table then means device D.
	392
	393	config ENV_FAT_FILE
	394	string "Name of the FAT file to use for the environemnt"
	395	depends on ENV_IS_IN_FAT
	396	default "uboot.env"
	397	help
	398	It's a string of the FAT file name. This file use to store the
	399	environment.
	400
1087a794 JRO	401	config ENV_EXT4_INTERFACE
	402	string "Name of the block device for the environment"
	403	depends on ENV_IS_IN_EXT4
	404	help
	405	Define this to a string that is the name of the block device.
	406
	407	config ENV_EXT4_DEVICE_AND_PART
	408	string "Device and partition for where to store the environemt in EXT4"
	409	depends on ENV_IS_IN_EXT4
	410	help
	411	Define this to a string to specify the partition of the device. It can
	412	be as following:
	413
	414	"D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
	415	- "D:P": device D partition P. Error occurs if device D has no
	416	partition table.
	417	- "D:0": device D.
	418	- "D" or "D:": device D partition 1 if device D has partition
	419	table, or the whole device D if has no partition
	420	table.
	421	- "D:auto": first partition in device D with bootable flag set.
	422	If none, first valid partition in device D. If no
	423	partition table then means device D.
	424
	425	config ENV_EXT4_FILE
	426	string "Name of the EXT4 file to use for the environemnt"
	427	depends on ENV_IS_IN_EXT4
	428	default "uboot.env"
	429	help
	430	It's a string of the EXT4 file name. This file use to store the
	431	environment (explicit path to the file)
	432
0649cd0d SG	433	if ARCH_SUNXI
	434
	435	config ENV_OFFSET
	436	hex "Environment Offset"
	437	depends on !ENV_IS_IN_UBI
	438	depends on !ENV_IS_NOWHERE
	439	default 0x88000 if ARCH_SUNXI
	440	help
	441	Offset from the start of the device (or partition)
	442
	443	config ENV_SIZE
	444	hex "Environment Size"
	445	depends on !ENV_IS_NOWHERE
	446	default 0x20000 if ARCH_SUNXI
	447	help
	448	Size of the environment storage area
	449
	450	config ENV_UBI_PART
	451	string "UBI partition name"
	452	depends on ENV_IS_IN_UBI
	453	help
	454	MTD partition containing the UBI device
	455
	456	config ENV_UBI_VOLUME
	457	string "UBI volume name"
	458	depends on ENV_IS_IN_UBI
	459	help
	460	Name of the volume that you want to store the environment in.
	461
	462	endif
	463
81f53b0d KG	464	if ARCH_ROCKCHIP
	465
	466	config ENV_OFFSET
	467	hex
	468	depends on !ENV_IS_IN_UBI
	469	depends on !ENV_IS_NOWHERE
	470	default 0x3f8000
	471	help
	472	Offset from the start of the device (or partition)
	473
	474	config ENV_SIZE
	475	hex
	476	default 0x8000
	477	help
	478	Size of the environment storage area
	479
	480	endif
	481
0649cd0d	482	endmenu